• 대한화학회지
• /
• 제54권6호
• /
• pp.749-754
• /
• 2010

본 연구에서는 IR과 CR의 블렌딩을 통하여 물성 개선 및 내구 성능 개선을 목적으로 IR/CR의 비율을 다양하게 블렌딩하여 제조한 고무시료의 가교 특성, 물성 변화, Morphology의 변화 및 화학적 특성을 조사하였다. 한편으로 블렌딩 된 고무에 다양한 조건으로 염소 표면처리를 하였을 때 고무시료의 Morphology를 관찰하고 마찰 시험을 통해 염소의 표면처리가 마찰계수에 미치는 영향을 조사하였다. 고무의 가교특성에서는 CR의 함량이 증가할수록 가교 속도가 감소하였으나 가교밀도는 일정하였고,경도, 모듈러스가 증가하였는데 이것은 가교특성의 변화와 밀접한 관계가 있으며, 가교 반응의 활성화에 의한 결정화 영향으로 기계적 강도가 증가하는 것으로 나타났다. 노화 후 물성 변화는 IR/CR Blend가 상호 기계적 물성의 단점을 보완하여 노화에 의한 물성 변화를 감소시키는 역할을 하는 것으로 나타났다. 염소 표면처리 한 시료의 노화 전, 후 상태물성의 변화는 감소하였다. 현미경 사진 관찰 결과 CR 함량 증가에 따라 표면 분산도가 증가함을 알 수 있었다. 염소 표면처리된 고무의 표면은 일정한 방향으로 균일하게 표면처리되었고 매끄러움과 광택이 증가하였다. 고무 표면의 개질 정도는 표면염소잔류량으로 확인할 수 있었으며, 마찰계수는 고무와 결합된 염소함량에 의존하는 것으로 나타났다. CR 함량이 10 - 40 phr까지는 표면처리 초기단계에서 마찰계수가 급격히 감소하였으나, 처리용액의 염소농도가 증가할수록 마찰계수의 감소는 둔화되었고, CR 함량이 50 phr에서는 처리용액의 염소농도 변화에 따라 마찰계수의 감소가 둔화되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.663-667
• /
• 2005

Surface modified carbon nanotubes were applied into the epoxy composites to investigate its tribological property. Carbon nanotubes reinforced epoxy composites were fabricated by casting. Effects to the tribological property of loading concentrations and types of surface modification of carbon nanotubes were investigated under sliding condition using linear reciprocal sliding wear tester. The results show that the small amount of carbon nanotubes into the epoxy exhibited lower weight loss than the pure epoxy. It is concluded that the effect of an enormous aspect ratio of carbon nanotubes surface area which wider than conventional fillers that react as interface for stress transfer. As increased the contents of carbon nanotubes, the weight loss from the wear test was reduced. And the surface modified carbon nanotubes show better tribological property than as produced carbon nanotubes. It is due that a surface modification of carbon nanotubes increases the interfacial bonding between carbon nanotubes and epoxy matrix through chemical bonding. Changes in worn surface morphology are also observed by optical microscope and SEM for investigating wear behaviors. Carbon nanotubes in the epoxy matrix near the surface are exposed, because it becomes the lubricating working film on the worn surface. It reduces the friction and results in the lower surface roughness morphology in the epoxy matrix as increasing the contents of the carbon nanotubes.

• Corrosion Science and Technology
• /
• 제8권3호
• /
• pp.103-109
• /
• 2009

An epoxy coating was designed to give a hydrophobic property on its surface by modifying it with three types of Amino Terminated Polydimethylsiloxane (ATP), and then effects of the modification on the structure, surface hydrophobic tendency, water transport behavior and hence corrosion protectiveness of the modified epoxy coating were examined using FT-IR spectroscopy, hydrothermal cyclic test, and impedance test. The surface of epoxy coating was changed from hydrophilic to hydrophobic property due primarily to a phase separation tendency between epoxy and modifier by the modification. The phase separation tendency is more appreciable when modified by ATP with higher molecular weight ATP at higher content. Water transport behavior of the modified epoxy coating decreased more in that with higher hydrophobic surface property. The resistance to localized corrosion of the modified epoxy coated carbon steel was well agreed with its water transport behavior and hydrophobic tendency.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.782-785
• /
• 1997

In this study, the spectra was surface-treated using $Ar^+$ ion beam to improve the tensile property of spectra/vinylester composites. The effect of surface treatment on the tensile property of spectra/vinylester composites was investigated comparing tensile strength and stiffness of surface-treated spectra/vinylester composites with those of untreated spectra/vinylester composites. The results showed that the tensile strength and stiffness of surface-treated s spectra/vinylester composites were 12% and 22% higher than those of untreated spectra/vinylester composites.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.458-458
• /
• 2012

Fuel Cell is used stacking metal or polymer substrate. This hydro property of substrate surface is very important. Usually, surface property is hydrophilic. The surface oxidation of SUS is investigated through plasma treatments with an atmospheric-pressure dielectric barrier discharge (DBD) for increasing hydrophilic property. The plasma process makes an experiment under various operating conditions of the DBD, which operating conditions are treatment time, plasma gas mixture ratio, the plasma source supply frequency. Two kinds of SUS substrate, SUS-304 and SUS 316L, were used. Discharge frequency has a crucial impact on equipment performance and gas treatment. After the plasma treatment of a SUS plate, highly improved wettability was noted. But, when high oxygen supply, the substrate damaged seriously.

• Journal of Electrochemical Science and Technology
• /
• 제1권2호
• /
• pp.112-116
• /
• 2010

Fractal property of the passivated steel surface was investigated on the basis of scaling analysis with a special focus on its relationship with corrosion resistance. For this purpose, the surface of stainless steel was intentionally oxidized under a variety of passivation conditions and its scaling property was analyzed by a triangulation method. The morphology of the passivated steel surface was satisfactorily evaluated with fractal dimension. From the chronoamperometry and impedance measurement, it proved that lower fractal dimension leads to more enhanced corrosion resistance. The higher passivity of the steel surface with lower fractal dimension was discussed in terms of active area and structural imperfection.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.113-120
• /
• 2013

Purpose: This study was to observe surface property and bonding strength according to composition of Ni-Cr alloy for porcelain fused to metal crown. The two kinds of Ni-Cr alloy with different composition ratio of parent metal were observed general properties and chemical properties of each alloy surface and measured the shear bonding strength between ceramic and each alloys. The aim of study was to suggest the material for design of parent metal's composition ratio to development of alloy for porcelain fused to metal crown. Methods: The two kinds of alloy as test specimen was Ni(71wt.%)-Cr(12wt.%) and Ni(63wt.%)-Cr(23wt.%) alloy. The oxide on surface was observed by SEM and EDX. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{71}Cr_{12}$ alloy measured 12.74wt.%, but $Ni_{63}Cr_{23}$ alloy was measured 15.91wt.%. And the maximum shear bonding strength was measured 106.14MPa between $Ni_{71}Cr_{12}$ alloy and vintage halo (VV group). Conclusion: The surface property and oxide characteristic of $Ni_{71}Cr_{12}$ alloy was similar to $Ni_{63}Cr_{23}$ alloy. And VV group has the strongest shear bonding strength.

• 융복합기술연구소 논문집
• /
• 제5권1호
• /
• pp.13-17
• /
• 2015

In wafer level molding progress, the thermal releasing failure phenomenon is shown up as the important problem. This phenomenon can cause the problem including the warpage, crack of the molded wafer. The thermal releasing failure is due to the insufficiency of adhesion strength degradation of the molding tape. To solve this problem, we studied experimental method increasing the release property of the molding tape through the plasma surface treatment on the wafer substrate. In this research, the vacuum plasma treatment system is used for release property improvement of the molding tape and controls the operating condition of the hydrophilic($O_2$, 100kW, 10min) and hydrophobic($C_2F_6$, 200kW, 10min). In order to perform the peeling test for measuring the releasing force precisely, we remodel the micro scale material property evaluation system developed by Korea institute of industrial technology. In case of hydrophilic surface treatment on the wafer substrate, we can figure out the releasing property of molding tape increase. In order to grasp the effect that it reaches to the release property increase when repeating the hydrophilic treatment, we make an experiment with twice treatment and get the result to increase about 12%. We find out the hydrophilic surface treatment method using plasma can improve releasing property of molding tape in the wafer level molding process.

• 한국의류학회지
• /
• 제24권2호
• /
• pp.277-285
• /
• 2000

The purpose of this study was to quantify the relationship between the sense of touch and mechanical properties of man-made leather. The first was to develop the five conversion equations which convert mechanical properties of man-made leather into five factor scores, which express five factors of the sense of touch(surface property, stretchiness, thickness & weight, thermal property(warmth & coolness), and moisture property(sticky & clingy)). The second was to develop the conversion equation which converts five factor scores into score of the sense of touch. Five factor scores were predicted by the following mechanical properties; surface property factor by log2HB and (log2HB)2, stretchiness factor by logEM, thickness & weight factor by logT, log2HB, logW, thermal property factor by logT, logHB, logSMd, and moisture property factor by logMMD, RC, RC2, (logEM)2, RT2. Subsequently, these five factor scores were converted into score of the sense of touch. The predictive abilities of the developed equations were satisfied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1682-1684
• /
• 2004

In this study, the surface properties of PET film were analyzed after plasma surface treatment. After plasma treatment of surface roughness and XPS were evaluated to analyze the chemical property, while the surface potential decay and surface resistivity was measured to analyze the electrical characteristic. When plasma discharge treatment was conducted for less than 10 minutes, the electrical insulating property was found to be improved through evaporation of low molecular weight materials and cleaning of surface. However, when the treatment was conducted for more than 10 minutes, the insulating property was decreased due to excessive discharge energy. Analysis of chemical characteristics showed that 10-minute treatment resulted in increase of C-O and O=C-O. However, when treated for more than 10 minutes, they were relatively decreased.