• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2013.06a
• /
• pp.134-135
• /
• 2013

In this study, the physical properties and antifouling were investigated to make the Marine growth antifouling coatings by blending of synthesized silicone resin and pigment with a low surface tension. To examine the film properties and foul release of the prepared coatings, film specimens were prepared with the prepared coatings and anti corrosion coatings. The test results showed that the silicone type antifouling coatings had very excellent antifouling properties rather than any other coatings because of the coating films had followed the low surface tension and elasticity, and prevention of adhesion for marine growth and mechanical adhesions.

• Journal of Welding and Joining
• /
• v.14 no.3
• /
• pp.66-74
• /
• 1996

In this study, friction and wear properties of flame sprayed specimens and hard Cr plating specimens were tested, and their properties were compared each other in dry and lubrication condition. Ni-Cr powder and steel powder were used as the spray powder and sprayed on the steel(S45C) substrate by flame sprayed method. Each wear surface was observed with SEM after friction and wear test. The friction coefficient of the as-forged steel specimens was the highest among surface treatment specimens, and the other specimens appeared in order as follows ; hard Cr-plating specimens, Ni-Cr powder sprayed specimens, steel powder sprayed specimens. Comparing the wear volumes in dry condition, as forged steel specimens appeared the greatest wear volume, and the other specimens appeared wear volume in order as follows ; Ni-Cr powder sprayed specimens, steel powder sprayed specimens, hard Cr plating specimens. In friction and wear test, the hard Cr plating specimens were worn by the abrasive phenomenon, involving the cracks. The wear volume of steel powder sprayed specimens was lower than that of Ni-Cr powder sprayed specimens. Comparing the tensile strength of both sprayed coating layers, the steel powder sprayed coating layer was better than Ni-Cr powder sprayed coating layer.

• Journal of Surface Science and Engineering
• /
• v.47 no.3
• /
• pp.137-146
• /
• 2014

The important drawback of epoxy electrodeposition(ED) coatings is the lack of the weathering resistance caused by the structure of bisphenol A. To improve this yellowing phenomena, acryl ED coatings have been developed. Compared with the epoxy ED coatings, however, acryl ED coatings are relatively weak in the corrosion resistance and mechanical properties. The purpose of this study is complemented their drawbacks by mixing epoxy and acryl ED paints. The salt spray, accelerated weathering test(QUV) and cupping, bending, impact test were employed to investigate the corrosion resistance, weathering resistance, and mechanical properties of ED coatings. When the ratio of acryl to epoxy resin of ED coating is 0.33, the weathering resistances are appropriately improved in condition maintaining the corrosion resistance. It was shown that the weathering resistance for epoxy ED coating was adjusted by optimally mixing acryl ED paint.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.2
• /
• pp.90-95
• /
• 2006

Nitriding or carburizing of carbon steels results in good mechanical properties such as high surface hardness and wear resistance but it has no affection on the corrosion resistance. Corrosion properties of nitriding and carburizing steels could be deteriorated. So, recently, there have been great demand for oxi-nitriding to enhance both mechanical properties and corrosion resistance. In this study, the corrosion resistance of carbon steel, S35C, and free cutting steel, SUM222, are prepared by vacuum nitriding and vacuum post-oxidation were compared with those treated by nitriding. After vacuum post-oxidation, $5{\mu}m$ oxide layer was formed on the nitride layer with $20{\sim}30{\mu}m$ depth. Potentio-dynamic polarization curve in corrosion test showed that the corrosion potential after post oxidation was increased from 200 mV to 800 mV in S35C and from 600 mV to 1200 mV in SUM222. SEM analyses showed that pores was increased and surface roughness became rougher with post oxidation. However, the formation of $Fe_3O_4$ resulted in the enhanced corrosion resistance of steels.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.304-309
• /
• 2009

Quenchable boron steel is a new type of high strength steel to reduce the weight of automobiles and maintain the safety conditions. Quenchable blanks can be hot-stamped and hardened in a water-cooled tool to achieve high strength. In this paper, new alloy for hot stamping is designed based on requirement of mechanical properties and two types of surface coating are investigated in viewpoints of oxidization and exfoliation. An automotive part of center pillar is manufactured by hot-stamping using Al-Si coated sheet. The performance of developed part is compared by static compression test and side impact crash test.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.1
• /
• pp.167-170
• /
• 2012

A test-area molecular dynamics simulation method for the vapor-liquid interface of argon through a Lennard-Jones intermolecular potential is presented in this paper as a primary study of interfacial systems. We found that the calculated density profile along the z-direction normal to the interface is not changed with time after equilibration and that the values of surface tension computed from this test-area method are fully consistent with the experimental data. We compared the thermodynamic properties of vapor argon, liquid argon, and argon in the vapor-liquid interface. Comparisons are made with kinetic and potential energies, diffusion coefficient, and viscosity.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.206-212
• /
• 2009

Chemical behaviors of each surface material for interior facilities affect to fire initiation and growth in general fire situation. These chemical behaviors were characterized by thermal properties (Heat release rate, Pyrolysis rate, specific heat, etc) which could be derived from experimental test. Especially, Heat release rate which indicates aspect of fire size is one of the most important property to asses fire hazard and protection needs. The cone calorimeter test (ISO 5660) has recently assumed to a dominant role in bench scale fire testing to obtain the Heat release rate of materials. This value could be calculated by the 'Oxygen Consumption Method' under various producing irradiances to each surface of materials. In this study, Process of the cone calorimeter test was simulated by Pyrolysis model of FDS (Fire Dynamics Simulator by NIST) base on the ISO 5660 international standard. Then, we could estimate the simulation method of FDS in case of single materials through the comparative study with test results.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.360.1-360.1
• /
• 2016

Hydroxyapatite (Ca10(PO4)6(OH)2, HAP) particles have attracted a great deal of attention in biomedical fields due to their good biocompatibility, bioactivity and fairly broad applications as drug delivery, dental implant, bone cement, and etc. Thus, many researchers have made an effort to add new functionalities such as luminescence, drug delivery, and bone regeneration properties up to HAP powders by controlling their nanostructure as well as composition. In this research, the mesoporous strontium substituted HAP (Sr-HAP) microspheres were synthesized using a hydrothermal method. In this synthesis, aspartic acid monomers were utilized to form microsphere by controlling surface energy of HAP particles and Sr ions were substituted into Ca ion sites, which induced luminescence property in HAP powders. Moreover, the change in the amount of Sr substitution was found to influence the particle size, morphology, and concurrently surface area, which led to changing drug loading as well as drug release property. The amount of Sr influences the morphology, luminescent properties, particle size, surface area cell viability and drug loading property, which are investigated by SEM, TEM, XRD, FTIR, BET, XPS and in vitro test such as MTT assay and drug release test. In particular, the multifunctional Sr-HAP with molar ratios of 0.25 (Sr/(Ca+Sr)) possessed the strongest luminescent property as well as the superior drug loading and sustained release properties that were correspondent with large surface area and pore size. Our study indicates that the fabricated multifunctional Sr-HAP microspheres are quite useful for bone regeneration and drug delivery.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.9
• /
• pp.19-26
• /
• 2018

The focus of this study was centered around 15 common injection type water leakage repair materials (3 different types for each; synthetic polymer, cementitious, acrylic, epoxy, urethane) used in concrete structures of Korea and analyzing their wet surface adhesion performance in accordance to the ISO TS 16774 Test Method for Repair Materials for Water-leakage Cracks in Underground Concrete Structures, Part 4: Test Method for Adhesion on Wet Concrete Surface, and the results of this study was taken to be place under a comparative analysis with the results of the preceeding study on response to substrate movement performance study. The results of this comparative study showed that other than 1 specimen of 1 type of the acrylic and 3 specimens of 1 type of the synthetic polymer type materials, all of the 93% of the specimens used in this study showed stable adhesion on wet substrate surface, and we were able to determine that materials that have proper response properties against substrate movement are highly flexible and have high adhesion properties, but their adhesion properties on wet substrate would change based on their viscosity.

• Tribology and Lubricants
• /
• v.38 no.4
• /
• pp.170-178
• /
• 2022

Mechanical surface treatment is an excellent approach widely used to modulate and improve the performance and service life of bearings, gears, and frictional joints. The main purpose of this study is to investigate and compare the effect of ultrasonic nanocrystal surface modification (UNSM) and wonder process craft (WPC) on the surface and tribological properties of SUJ2 bearing steel. The surface roughness and hardness of the untreated and treated (UNSM- and WPC-treated) specimens were measured and compared. Their tribological properties were evaluated using a micro-tribometer under grease-lubricated and dry conditions against itself. Surface hardness measurement results revealed that both the UNSM- and WPC-treated specimens had a higher hardness than that of the untreated specimen. The surface roughness of the untreated specimen was reduced after UNSM and WPC treatments. Abrasive wear mode was observed on the surface of the specimens worn under grease-lubricated conditions, while adhesive wear mode was found on the surface of the specimens worn in dry conditions. According to the tribological test results, the friction coefficient and wear rate of the untreated specimens were reduced by the application of both the UNSM and WPC treatments under grease-lubricated and dry conditions.