• 한국위성정보통신학회논문지
• /
• 제9권3호
• /
• pp.104-108
• /
• 2014

한국형발사체의 표면에 장착되는 UHF-대역 안테나의 표면에 발생하는 결빙을 모델링하고, 이러한 결빙이 안테나의 공진주파수, 반사손실 및 방사패턴 등의 주요 특성에 미치는 영향을 분석하였다. 안테나 표면결빙을 모델링하기 위해 $-180^{\circ}C$의 얼음층에 대한 비유전율을 추출하였고 추출된 비유전율을 이용하여 안테나 표면결빙 모델을 제안하였다. 중심주파수가 UHF-대역인 안테나 표면에 1mm의 결빙이 되었을 경우의 표면결빙 모델을 적용하여 시뮬레이션 한 결과, 표면결빙에 의해 안테나의 공진주파수가 21MHz 하향 되었고, 방사패턴도 전 방향에 대해 전체적으로 10dB 이상의 성능저하가 발생되었다. 따라서 실제 안테나 표면에 결빙이 발생할 경우 안테나 성능에 심각한 영향을 미칠 것으로 판단된다.

• 한국의류학회지
• /
• 제33권1호
• /
• pp.68-79
• /
• 2009

It is inevitable to have cutting line to get the 2D pattern from 3D body surface. In this paper the efficiency of curvature plot as a cutting line in the process of flattening 3D surface was investigated. As reference, basic clothing construction line was adopted to divide the 3D surface into small blocks to make the flattening process easy. Female dummy as well as human body were scanned and surface of the upper body was segmented using curvature plot and basic constructing line. 2D tight-fit pattern was developed using three software, the RapidForm 2004, 2C-AN and Yuka CAD. Gap between clothes and body, and the clothing pressure on the body was observed to determine the fit of the clothes. As results, clothes constructed with blocks divided by curvature plot displayed a similar level of tight fit as compared with those by basic construction line. It was found that curvature plot is effective method as a segmentation of the 3D surface even for the actual body which does not have any previous reference line. It is expected that application of curvature plot will be expanded in 3D apparel technology.

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.24-31
• /
• 2004

The objective of this work is to suggest a mastless pattern fabrication technique using the combination of machining by Nanoindenter(equation omitted) XP and HF wet etching. Sample line patterns were machined on a borosilicate surface by constant load scratch (CLS) of the Nanoindenter(equation omitted) XP with a Berkovich diamond tip, and they were etched in HF solution to investigate chemical characteristics of the machined borosilicate surface. All morphological data of scratch traces were scanned using atomic force microscope (AFM).

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.267-272
• /
• 2001

The effect of characteristic of surface roughness and roughness patterns on frictioin was studied experimentally in boundary lubrication with reciprocating tribometer. Roughness was changed from Ra=0.2 $\mu\textrm{m}$ to Ra=1.2 $\mu\textrm{m}$. Three roughness patterns-transverse, oblique, longitudinal- were tested for various load. Ra=1.0 $\mu\textrm{m}$ roughness showed lower friction coefficient and transversal pattern showed lower friction and high scuffing load in the test conditions.

• 한국의류학회지
• /
• 제41권4호
• /
• pp.646-660
• /
• 2017

This study provides basic data to develop a brassiere pattern that can cover the big breast of breast enlargement patients. In this study, we also showed areas of the brassiere cup pattern and the body surface of the breast on a breast enlargement patient. The results of the study are as follows. Correlation analysis was obtained between volume and body surface area and breast detail dimensions. After the correction process, we proposed a research bra pattern for breast augmentation patients. The cup-boundary in bra patterns of breast enlargement surgery patients is longer than the bra patterns of the general breast; therefore, the height of the inner and outer edges of the upper cups is higher. Also, it is necessary to set the new breast upper point when measuring the upper length in patients with breast augmentation surgery because the points of circumference of the breast are marked higher than chest circumference.

• International Journal of Oral Biology
• /
• 제38권4호
• /
• pp.161-167
• /
• 2013

Human dental pulp stem cells (DPSCs) are multi-potent mesenchymal stem cells that have several differentiation potentials. An understanding of thetissues that differentiate from these cells can provide insights for future regenerative therapeutics and tissue engineering strategies. The mesiodens is the most frequent form of supernumerary tooth from which DPSCs can differentiate into several lineages similar to cells from normal deciduous teeth. Recently, it has been shown that nanoscale structures can affect stem cell differentiation. In our presentstudy, we investigated the effects of a 250-nm nanoscale ridge/groove pattern array on the osteogenic and adipogenic differentiation of dental pulp cells from mesiodenscontaining human DPSCs. To this end, the expression of lineage specific markers after differentiation induction was analyzed by lineage specific staining and RT-PCR. The nanoscale pattern arrayed surface showed apositive effect on the adipogenic differentiation of DPSCs. There was no difference between nanoscale pattern arrayed surface and conventional surface groups onosteogenic differentiation. In conclusion, the nanoscale ridge/groove pattern arrayed surface can be used to enhance the adipogenic differentiation of DPSCs derived from mesiodens. This finding provides an improved understanding of the effects of topography on cell differentiation as well as the potential use of supernumerary tooth in regenerative dental medicine.

• 한국기계가공학회지
• /
• 제20권2호
• /
• pp.51-57
• /
• 2021

The quality of the ceramic sintered coating on a metal surface through laser surface treatment is affected by the laser irradiation pattern. Depending on the laser irradiation pattern, the amount of residual stress and heat applied or accumulated on the surface increases or decreases, affecting the thickness attained in the ceramic sintering area. When the heat energy accumulated in the sintering area is high, the ceramic and the metal alloy melt and sufficiently mix to form a homogeneous and thick bonding interface. In this study, the thermal energy accumulation in the region sintered with zirconia was controlled using four types of laser processing patterns. The thickness of the diffusion region is analyzed by laser-induced breakdown spectroscopy of Mg-ZrO2 generated by laser sintering zirconia powder on the magnesium alloy surface. On the basis of the analysis of the Mg and Zr present in the sintered region through LIBS, the effect of the irradiation pattern on the sintering quality is confirmed by comparing and analyzing the heat and mass transfer tendency of the diffusion layer and the degree of diffusion according to the irradiation pattern. The derived diffusion coefficients differed by up to 9.8 times for each laser scanning pattern.

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.64-72
• /
• 1994

Zinc Phosphate Cement hand been used for about more than 100 years in luting of cast gold inlay. But many scientists had been trying to develop the new form of luting agent because the ZPC hand shown the lack of adhesiveness on the tooth structure and the toxicity to the pulp tissue. Recently many researches about the surface treatment of the cast body are being done to increase the adhesion of cement to it. The conventional Class I gold inlays were fabricated in the 20 permanent molars. After the internal surface of the cast body was sandblasted with $Al_2O_3$ particles and was tin-plated, the inlays were cemented with adhesive cement [G I cement and resin cement(Super-Bond & $Panavia_{EX}$)] and the evaluation on the adhesion pattern, adhesive strength and the fracture pattern of the adhesive cast gold inlay was compared to that of the cast gold inlay cemented conventionally with ZPC. The results were as follows : 1. The surface roughness of the cast body was increased significantly after sandblasting with the $Al_2O_3$ particles and the tin oxide layer, which was consisted of round particles, came into being. 2. The bond strength was in the order of Super-Bond, ZPC, Fuji I, $Panavia_{EX}$ group. The group cemented with Super-Bond showed statistically greater strength than the other groups(p<0.05). 3. The group cemented with ZPC was fallen apart by principal adhesion failure and that with Fuji I was by complete adhesion failure. But the group with Super-Bond showed pricncipal cohesive failure pattern and in the group with $Panavia_{EX}$, complete cohesive fracture pattern was shown and small protion of tooth structure was fractured out with cast body and the fractured surface showed the figure just as the enamel prism. 4. Various gaps were shown at the pulpal side regardless of little gap at the side walls of the cavity in all groups. Only the Super-Bond was attached to the tooth structure and the other cements were detached from both the tooth and the cast body.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.397-401
• /
• 1995

ESPI(Electronic Speckle Pattern Interfermetry) is an optical technique to measure surface deforamtion of engineering components and materials in industrial ares. This optical method is capable of providing full-field results with high spatial resolution, high speed and is the non-contact technique. One of important application aspects using electronic speckle pattern interferometry is to generate contours of a diffuse object in order to provide data for 3-D shape analysis and topography measurement. The contouring method by modified dual-beam speckle pattern interferometry is proposed. We introduce a shift of the illumination beams through optical fiber in order to obtain the contour fringe patterns. The speckle pattern correlation technique is suitable for providing measurement range from millimeters to several centimeters. The complete geometric analysis of the contoretical and experimental results are obtained.

• 소성∙가공
• /
• 제15권1호
• /
• pp.71-75
• /
• 2006

In recent, various shapes of pattern in micron or nano scale are adapted in many applications due to their good mechanical or optical properties. Light guide panel (LGP) of the LCD is one of important applications for micro pattern and micro prism shape is one of the typical patterns. The size of the surface patterns in most applications is decreasing to the order of micron or even under micron. On the other hand, the area to be patterned keeps enlarging. These two trends in patterned products require tooling micro patterns on large surface, which has still many technical problems to be solved mainly due to pattern size and the tooling area. In this study, we fabricated prism shape of patterns using diamond cutting tool on some metal core and plastic core like PMMA. Some cutting conditions were investigated including cutting force, cutting depth and speed for different core materials.