• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.725-729
• /
• 2000

This paper presented a new model of NC verification in ball end milling. The model verifies the over cut the under cut and the surface roughness using NC file generated from CAM and cutting condition. The model uses Z-map model to verify workpiece. In this paper, the model used the velocities of x, y and z direction and obtained a center point of a ball end mill for modeling Z-map of workpiece. To investigate the performance of the model simulation study was carried out. As the results, the model gave geometry accuracy of workpiece, the surface roughness and the chip loads in finish cutting that can predict tool chipping.

• International Journal of Internet, Broadcasting and Communication
• /
• 제14권2호
• /
• pp.136-146
• /
• 2022

Some surface defects make the weak quality of steel materials. To limit these defects, we advocate a one-stage detector model RetinaNet among diverse detection algorithms in deep learning. There are several backbones in the RetinaNet model. We acknowledged two backbones, which are ResNet50 and VGG19. To validate our model, we compared and analyzed several traditional models, one-stage models like YOLO and SSD models and two-stage models like Faster-RCNN, EDDN, and Xception models, with simulations based on steel individual classes. We also performed the correlation of the time factor between one-stage and two-stage models. Comparative analysis shows that the proposed model achieves excellent results on the dataset of the Northeastern University surface defect detection dataset. We would like to work on different backbones to check the efficiency of the model for real world, increasing the datasets through augmentation and focus on improving our limitation.

• 한국환경과학회:학술대회논문집
• /
• 한국환경과학회 2003년도 International Symposium on Clean Environment
• /
• pp.19-26
• /
• 2003

The dispersion of recycled particulates in the complex coastal terrain containing Kangnung city, Korea was investigated using a three-dimensional non-hydrostatic numerical model and lagrangian particle model (or random walk model). The results show that particulates at the surface of the city that float to the top of thermal internal boundary layer (TIBL) are then transported along the eastern slope of the mountains with the passage of sea breeze and nearly reach the top of the mountains. Those particulates then disperse eastward at this upper level over the coastal sea and finally spread out over the open sea. Total suspended particulate (TSP) concentration near the surface of Kangnung city is very low. At night, synoptic scale westerly winds intensify due to the combined effect of the synoptic scale wind and land breeze descending the eastern slope of the mountains toward the coast and further seaward. This increase in speed causes development of internal gravity waves and a hydraulic jump up to a height of about 1km above the surface over the city. Particulate matter near the top of the mountains also descends the eastern slope of the mountains during the day, reaching the central city area and merges near the surface inside the nocturnal surface inversion layer (NSIL) with a maximum ground level concentration of TSP occurring at 0300 LST. Some particulates were dispersed following the propagation area of internal gravity waves and others in the NSIL are transported eastward to the coastal sea surface, aided by the land breeze. The following morning, particulates dispersed over the coastal sea from the previous night, tend to return to the coastal city of Kangnung with the sea breeze, developing a recycling process and combine with emitted surface particulates during the morning. These processes result in much higher TSP concentration. In the late morning, those particulates float to the top of the TIBL by the intrusion of the sea breeze and the ground level TSP concentration in the city subsequently decreases.

• 대한전자공학회논문지SD
• /
• 제41권2호
• /
• pp.9-15
• /
• 2004

본 논문에서는 부분공핍(partially-depleted : PD) 영역과 완전공핍(fully-depleted : FD) 영역을 나누는 임계 전면 게이트 전압 V/sub c/의 해석적 표현을 이용해서 PD 영역과 FD 영역의 천이를 정확히 설명하는 해석적 표면전위 모델(analytical surface potential model)을 소개한다. 이 모델은 모든 동작영역(subthreshold에서 strong inversion까지)에서 유효하고 반복 계산 절차 (iteration procedure)인 수치 해석적 방법보다 훨씬 짧은 계산시간이 걸린다. 이 모델에 기초한 charge sheet 모델이 모는 동작영역에 유효한 드레인 전류의 단일 공식을 유도하는데 사용된다. 대부분의 secondary 효과들이 charge sheet 모델에 쉽게 포함되고 그 모델의 결과들은 수치해석 결과와 실험 결과를 비교적 정확히 일치한다. 세 가지의 smoothing 함수가 사용될지 라도 표면전위 미분 값은 연속이다 더욱 중요한 점은 smoothing 함수에 사용된 파라미터들은 공정 파라미터들에 크게 의존하지 않는다.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권1호
• /
• pp.101-108
• /
• 2016

The RCS characteristics of stealth modified three-surface aircraft are analyzed in this paper. Prototype A is built with CATIA software and the three-dimensional digital models of modified stealth three-surface B and C are also designed based on carrier-based aircraft Su-33; the numerical simulation of RCS characteristics of three-surface aircraft is conducted with RCSAnsys software based on physical optics method and the method of equivalent currents; The following results are obtained by comparative analysis and mathematical statistics: (1) by the use of physical optics method and equivalent electromagnetic current method, the scattering intensity for each part of the model and RCS characteristic of the aircraft can be analyzed efficiently and accurately; (2) compared with model A, the mean RCS value of model B is reduced to 14.1% in forward direction and 48.1% in lateral direction; (3) compared with model A, the mean RCS value of model C decreases to 11.4% in forward direction and 21.6% in lateral direction. The results are expected to provide theoretical basis and technical support to the conceptual design of aircraft and stealth technology research.

• 한국산학기술학회논문지
• /
• 제4권3호
• /
• pp.296-300
• /
• 2003

다성분 양이온 교환을 위한 평형과 동역학 데이터는 질량 작용 법칙과 표면 착화 모델을 이용하여 수행 및 평가하였다. 양이온 흡착의 평형과 칼럼 실험은 양이온 교환 합성 수지 IRN 77로 H/sup +/, Li/sup +/, Na/sup +/, NH₄/sup +/, Mg²/sup +/ 이용하여 2, 3, 4, 5 성분 양이온 교환을 수행하였다. 질량 작용 법칙과 표면 착화 모델은 이온 선택도와 경쟁적 양이온 교환을 조사하기 위하여 데이터에 대해 시험하였다. 표면 착화 모델은 질량 작용 모델보다 평형과 동역학 실험 데이터를 정확히 예측하였다.

• 한국측량학회지
• /
• 제40권4호
• /
• pp.305-313
• /
• 2022

The evolution of the GNSS (Global Navigation Satellite System) technology has enhanced positioning performance in terms of positioning accuracy and time efficiency. The technology makes it possible to determine orthometric heights at a few centimeter accuracies by transforming accurate ellipsoid heights if an accurate geoid model has been employed. This study aims to generate a correction surface using GNSS/leveling co-points and a local geoid model, Thailand Geoid Model 2017 (TGM2017), through the Kriging interpolation method in a small local area. Combining the surface and TGM2017 significantly improves height transformation with the 1-cm RMSE (Root Mean Square Error) fit of 10 GNSS/leveling reference points and a mean offset of +0.1 cm. The evaluation of the correction surface at 5 GNSS/leveling checkpoints shows the RMSE of 1.0 cm, which is 82.6 percent of accuracy improvements. The GNSS leveling method can possibly be used to replace a conventional leveling technique at a few centimeter uncertainties in the case of small areas with clear-sky and high satellite visibility environments.

• Geomechanics and Engineering
• /
• 제11권3호
• /
• pp.325-343
• /
• 2016

A total stress-based bounding surface model is developed to predict the undrained behaviour of saturated soft clays under cyclic loads based on the anisotropic hardening modulus field and bounding-surface theories. A new hardening rule is developed based on a new interpolation function of the hardening modulus that has simple mathematic expression and fewer model parameters. The evolution of hardening modulus field is described in the deviatoric stress space. It is assumed that the stress reverse points are the mapping centre points and the mapping centre moves with the variation of loading and unloading paths to describe the cyclic stress-strain hysteresis curve. In addition, by introducing a model parameter that reflects the accumulation rate and level of shear strain to the interpolation function, the cyclic shakedown and failure behaviour of soil elements with different combinations of initial and cyclic stresses can be captured. The methods to determine the model parameters using cyclic triaxial compression tests are also studied. Finally, the cyclic triaxial extension and torsional shear tests are performed. By comparing the predictions with the test results, the model can be used to describe undrained cyclic stress-strain responses of elements with different stress states for the tested clays.

• 한국농공학회지
• /
• 제34권1호
• /
• pp.87-99
• /
• 1992

A mathematical model, UNSATR which predicts the seepage flow through the body of dike especially under the tidal fluctuation has been developed. This model has been revised from UNSAT2 model which was developed on the basis of the saturated-unsaturated theory by Neuman. UNSATR has been verified and applied to the hydraulic model in order to estimated the seepage quantity, the formation of free water surface etc. The results lead to the following conclusions : 1. Seepage rates between the mathematical model and hydraulic model experiment are very similar to each other both in constant and transient water level conditions. 2. The lapsed time to be steady state of the free water surface becomes late as the tidal levels are relatively low mainly due to the seepage flow from the unsaturated zone of the body of dike. 3. Under the transient state of water levels, owing to the flow from the unsaturated domain, streamlines crossing to the free water surface are found and time lag during a falling tide may allow the free water surface inside the body of dike to stand at a high level than the outside water level. 4. The utility and validity of UNSATR model are convinced when the analyses on seepage problems through the porous embankment of the soil structures on the conditions of the steady and unsteady states are carried out.

• 대한치과교정학회지
• /
• 제44권5호
• /
• pp.229-235
• /
• 2014

Objective: The aim of this study was to assess artifacts induced by metallic restorations in three-dimensional (3D) dental surface models derived by cone-beam computed tomography (CBCT). Methods: Fifteen specimens, each with four extracted human premolars and molars embedded in a plaster block, were scanned by CBCT before and after the cavitated second premolars were restored with dental amalgam. Five consecutive surface models of each specimen were created according to increasing restoration size: no restoration (control) and small occlusal, large occlusal, disto-occlusal, and mesio-occluso-distal restorations. After registering each restored model with the control model, maximum linear discrepancy, area, and intensity of the artifacts were measured and compared. Results: Artifacts developed mostly on the buccal and lingual surfaces. They occurred not only on the second premolar but also on the first premolar and first molar. The parametric values increased significantly with increasing restoration size. Conclusions: Metallic restorations induce considerable artifacts in 3D dental surface models. Artifact reduction should be taken into consideration for a proper diagnosis and treatment planning when using 3D surface model derived by CBCT in dentofacial deformity patients.