• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.6
• /
• pp.435-442
• /
• 2009

Three-dimensional heat transfer characteristics for natural convection flows are numerically investigated in the doubly-inclined cubical-cavity according to the variation of a newly defined orientation angle �� of the hot wall surface from horizontal plane at moderate Rayleigh numbers. Numerical simulations of laminar flows are conducted in the range of Rayleigh numbers($10^4{\leq}Ra{\leq}10^5$) and $0^{\circ}{\leq}{\alpha}90^{circ}$ with a solution code(PowerCFD) employing unstructured cell-centered method. Comparisons of the average Nusselt number at the cold face are made with benchmark solutions and experimental results found in the literature. It is found that the average Nusselt number at the cold wall has a maximum value around the specified orientation ${\alpha}$ at each Rayleigh number. Special attention is also paid to three-dimensional thermal characteristics in natural convection according to new orientation angles at Ra��= $1{\times}10^5$, in order to investigate a new additional heat transfer characteristic found in the range of above Ra = $6{\times}10^4$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.622-629
• /
• 1988

In order to improve the sensitivity of the wafer type heat flux sensor, some heat flux sensors were manufactured and examined by using thermoelectric semiconductor material (bismuth telluride) whose Seebck coefficient is much larger than those of metallic thermocouple materials. Because the thermoelectric element cannot be bended or welded, a peculiar sensor structure and manufacturing process were designed. As a result, it is revealed that the characteristic sensitivity of the manufactured sensor is about 10 times larger than that of marketed sensor even though there are some troubles in stiffness for reciprocal use. If we make this kind of sensors smaller and thinner, it will be a useful method to measure the local heat flux from the surface of complex configuration.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.2-31.2
• /
• 2009

In this research, single walled carbon nano-tube film was manufactured with spray coating method on glass for application as transparent heat element. SWNTs solution to be used for spraying is obtained by dispersion of 0.01 wt% purified SWNTs in dimethylformamide (DMF) solution through ultrasonification and centrifugation. The transmittance and sheet resistance of SWNTs film were determined by the number of spray injection. Manufactured SWNTs film will have sheet resistance range of $200\;\Omega/\square-900\;\Omega/\square$ at transmittance range of 70-90 %. Heat generation characteristic of SWNTs film was measured by applying constant DC voltage of 15V. The result confirmed that SWNTs film with sheet resistance of $200\;\Omega/\square$ reaches surface temperature of $80^{\circ}C$ within several seconds. In addition, PET coating film was coated on top of the SWNTs film by using laminator in order to solve weak adhesive property of the spray coated SWNTs film on the substrate as well as to maintain its electrical and optical properties.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.25 no.3
• /
• pp.1-16
• /
• 2022

Areas developed through land reclamation projects have huge economic advantages in terms of supplying lands that can be used for farmlands, urban areas and etc., however have relatively small areas of grasslands and densely located buildings compared to inland cities. Hence, an urban heat island is occurring in these areas due to this characteristic, and in particular, the urban heat island in Cheongna International City is getting serious. In this study, the urban heat island in Cheongna International City was evaluated and analyzed by classified into the three periods after the reclamation project: farmland(2001-2008), development(2009-2013) and artificial grassland(2014-2020). The land cover map and Landsat time-series imagery were utilized for measuring the differences of the land surface temperatures between the urbanized areas and the grassland/forest areas in Cheongna International City. The statistical results showed that the differences in the land surface temperature between these areas were calculated to be at most 0℃ during the period of farmland, at most 3.60℃ during the period of development, and at most 2.51℃ during the period of grassland. This study proved that the urban heat island phenomenon increased when the urbanized areas increased, and the urban heat island phenomenon decreased when the artificial grassland areas increased in Cheongna International City where the reclamation project was carried out. The statistical results derived through this research can be used as the reference data for identifying the urban heat island problem in urban planning and establishing the reduction plan.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1466-1473
• /
• 2012

Soft icecream is made by scraping an ice formed on the inside of the cylindrical evaporator, where R-404A is evaporating in the annulus. The heat transfer characteristics of the refrigerant evaporation and those during icecream formation were experimentally investigated. Results show that the refrigerant-side heat transfer coefficients are highly dependent on the location in the evaporator due to the complex annulus configuration. The heat transfer coefficient at the inlet is generally lower than those of other locations. The average heat transfer coefficient increases as heat flux increases or saturation temperature decreases. A correlation is developed to predict the refrigerant-side heat transfer coefficient. The icecream-side heat transfer coefficient oscillates continuously due to the periodic removal of ice formed on the surface. The average heat transfer coefficient during icecream formation is approximately 280 W/$m^2K$, and that during single-phase cooling increased from 150 W/$m^2K$ to 250 W/$m^2K$.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.9
• /
• pp.783-790
• /
• 2014

Railway wheels and axles are the most critical parts of the railway rolling stock. The wheel carry axle loads and guide the vehicles on the track. Therefore, the contact surface of wheel are subjected to wear and fatigue process. The wheel damage can be divided into three types; wear, contact fatigue failure and thermal crack due to braking. Therefore, in the contact surface between the wheel and the rail, the materials are heat treated to have a specific hardness. The manufacturing quality of the wheel have a considerable influence on the formation of tread wear and damage. Also, the residual stress on wheel is formed during the manufacturing process is one of the main sources of the damage. In this paper, the mechanical characteristic and the residual stress according to wheel material have been evaluated by applying finite element analysis and conducting mechanical tests.

• Journal of the Korean Chemical Society
• /
• v.8 no.2
• /
• pp.68-74
• /
• 1964

Water has the melting point, the boiling point, the heat of fusion, and the heat of vaporization all much higher than would be normally expected from the hydrogen compounds of the other members of the oxygen family. Another unique characteristic of ice-Ⅰ is its volume decrease which takes place in its melting. A number of significant efforts have been made in the past to explain these properties quantitatively. The authors, reasoning from the unusually great free surface energy of water and the characteristic volume change on melting, propose the structural model of liquid water as follows. On melting, fluidized vacancies of a molecular size are introduced. Thereupon, for the unusually great surface energy density, molecules surrounding the vacancies become to have close packed arrangement. But molecules not in direct contact with vacancies should still possess the original structure i. e., ice-Ⅰ. When a molecule adjacent to a vacancy jumps into the vacancy, the molecule attains the gaslike degree of freedom. Using the above model, the authors had developed the liquid partition function of water by applying the theory of significant structures in liquids. Molar volume, vapor pressure, entropy of fusion and entropy of vaporization were calculated over a wide temperature range. The results show good agreement with experimental observations.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.33-38
• /
• 2006

The Dish/Stirling system with the Stirling engine is currently used to convert solar energy directly to electrical energy. Successful operation of dish/Stirling system is supported by hybrid system, which will allow continuous operation driven by solar and combustion heating. The hybrid Receiver has to be provided with an additional combustion system. The heat pipe receiver and conbustion system were manufactured and tested for thermal characteristics of receiver. Maximum temperature difference along the heat pipe surface is $200^{\circ}C$. Emission measurements showed low NOx values of 28 to 46 ppm and very high CO values of 18 to 201 ppm.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.3
• /
• pp.138-144
• /
• 2005

In order to select a new material for a heat exchanger, the frosting behavior of a thermally conductive plastic based on PBT was compared to the frosting behavior of aluminum and three types of plastics based on PTFE. The frosting behavior on the 1 mm thick PBT specimen was similar to that of the aluminum specimen but not that of the pure PTFE specimen. The properties of the frost formed on the specimens were affected by both the thermal conductivity and surface characteristics of the materials. The heat and mass transfer rates of the thermally conductive plastic were almost equivalent to those of the aluminum specimen.

• Archives of Metallurgy and Materials
• /
• v.64 no.3
• /
• pp.917-920
• /
• 2019

Usually porous metals are known as relatively excellent characteristic such as large surface area, light, lower heat capacity, high toughness and permeability for exhaust gas filter, hydrogen reformer catalyst support. The Ni alloys have high corrosion resistance, heat resistance and chemical stability for high temperature applications. In this study, the Ni-based porous metals have been developed with Hastelloy powder by gas atomization and water atomization in order to find the effects of powder shape on porous metal. Each Hastelloy powder is pressed on disk shape of 2 mm thickness with 12 tons using uniaxial press machine. The specimens are sintered at various temperatures in high vacuum condition. The pore properties were evaluated using Porometer and microstructures were observed with SEM.