• Textile Coloration and Finishing
• /
• v.24 no.2
• /
• pp.131-137
• /
• 2012

para-Aramid fibers were treated by low-temperature plasma to improve the adhesion. The surface of para-aramid fibers were treated with gaseous plasma of several discharge power and treatment time in oxygen gas at 1Torr pressure. The treated fibers at low-temperature plasma were taken oxygen-containing functional groups and micro-crator on the surface. The modified fibers were measured by dynamic contact angle analyzer and XPS(X-ray photoelectron spectroscopy). The Interfacial adhesion properties of aramid fabric and polyurethane resin were determined by T-peel test. The surface of aramid fibers were observed by FE-SEM photographs. It was found that surface modification and chemical component ratio of the aramid fibers were improved wettability and adhesion characterization.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.1
• /
• pp.121-128
• /
• 2014

Superfinishing is essential for mirror surfaces, because among mechanical components cylindrical workpieces such as spindles must maintain precision and reliability with respect to functional characteristics. However, research on standardization of polishing film application combination to obtain mirror surfaces is insufficient. Consequently, this has been a factor in rising costs of mechanical components. Therefore, in this study, experiments have been conducted to determine efficient polishing film application combination for mirror surfaces ranging from ductile materials such as SM45C, brass, aluminium 7075, and titanium to brittle materials such as $Al_20_3$, SiC, $Si_3N_4$, and $ZrO_2$. From the experimental results, efficient polishing film application combination for metallic materials and ceramic materials is confirmed.

• Textile Coloration and Finishing
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2008

The study has attempted to introduce a new coating than the conventional standardized method of spray, padding and roll coating. The study has focused on finding condition for separating water and organic layer in marble bath and surface effects according to kind of raw hide. It was found that dyestuff-free was to be used in water layer and the input amount of initial insoluble pigment to be added in marble bath should be adjusted following the change of surface area of the marble bath in order to get efficient marble effect while preventing coagulation of water and organic layers. Eventually, amorphous high value-added leather could be obtained treated in process other than the conventional standardized method. Even raw hides of low grades($C{\sim}E$ grades) could be processed into amorphous marble effect that could conceal or shield surface scratches by the colorant, which eventually eliminated necessity of using excessive amount of chemicals in the coating process leading to achieving high quality marble leather of natural look.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.10
• /
• pp.52-59
• /
• 2006

Micro electrical discharge machining (EDM) and micro electrochemical machining (ECM) were studied for the fabrication of micro structures. Micro EDM has been used to machine micro structures from metals. However, since the tool wear is inevitable during the machining, the tool wear is drawback for the precision machining. Micro ECM is also used for micro machining and produces better surface quality than that of micro EDM. Moreover, since tool electrodes are not worn out, micro ECM is suitable for the precision micro machining. However, the machining rate is lower than that of micro EDM. In this paper, therefore, the hybrid machining process which uses micro EDM as roughing and micro ECM as finishing is introduced. By using this hybrid machining, a hemisphere with $100\;{\mu}m$ radius was fabricated and the efficiency of the process was investigated experimentally.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.1-8
• /
• 2017

This paper concerns the possibility of 3D printing reverse idle gears for tractor transmission. For the purposes of this experiment, idle gears were manufactured using a SLA 3D printer, FDM 3D printer, and through machining. The accuracy of the idle gears produced in these three different ways were evaluated by the properties of their outer diameter, inner diameter, roundness, concentricity, parallelism, span, backlash, and gear grade. The tooth characteristics of the idle gears were evaluated by their profile, lead, and the pitch of the gears. The results of this experiment determined that the surface conditions created by the finishing process had a significant impact on the dimensional accuracy of the gears and the characteristics of their teeth.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.493-497
• /
• 2002

In the part industry, pipe has required high accuracy in surface roughness and size. Especially, when producing the high frequency welding pipe, cutting process is very important as the finishing process that remove the hot welding bead. The objective of this paper is to investigate the hot machining high frequency welded pipe by simulation and experimental tests. To test the cutting process as hot machining, all cutting environment is reproduced in turning with heating system, and the test is accomplished by comparing with room temperature machining and hot machining in consideration of cutting force, tool wear and cutting temperature.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.4
• /
• pp.40-46
• /
• 2013

When impeller machining needs to be machined over a length in order to avoid interference with neighboring surfaces between material and tool, there are no databases about cutting condition according to tool slenderness ratio. So selection and machining of cutting condition depends on expert's experience. Therefore, the purpose of this paper is deciding cutting condition in roughing and finishing process of impeller according to slenderness ratio of AL7075's end-mill that is the most commonly used for impeller. We have tested for about relation between Slenderness ration and fluctuation width of the cutting force, surface roughness and depth of cut ratio to observe cutting characteristics according to slenderness ratio. The experiments of cutting characteristics and processing criteria are compared with AL5052 which is existing information.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.274-278
• /
• 2002

Surface finishing is still indispensable for most rapid prototyping (RP) processes because of the inherent stair-stepped surface and shrinkage of the parts. These problems can be minimized in the $VLM-_ST$ Process, because it uses expandable polystyrene foam sheets, each of which has a thickness of3.9 mm and a linear-interpolated side slope. The use of thick layers, however, limits the process capability of constructing fine details. This study focuses on the design of post-processing tool for fine details of $VLM-_ST$ parts and investigation of thermal characteristics during EPS foam cutting using the post-processing tool. To calculate the heat flux from the tool into the foam sheet, the tool was modeled as a heat source of radiation for finite element analysis. Results of the analysis agreed well with those of the experiment.

• Design & Manufacturing
• /
• v.13 no.1
• /
• pp.13-18
• /
• 2019

The size and prospects of the domestic semiconductor equipment market are increasing every year. In the case of various parts used inside semiconductor equipments, high durability such as high strength and abrasion resistance is demanded. Particularly, the gases used in semiconductor production processes are toxic. In order to prevent such toxic gas leakage, a precision processing technique and a surface treatment technique for preventing corrosion are required. Electro-polishing is an electro-chemical method of polishing a metal surface to make it smooth and polished. Electro-polishing is mainly used in the finishing process of metal surface. Unlike mechanical polishing, electro-polishing is used in many fields, such as fine chemical etching equipment, since no damaged layer or burr, fine polishing groove and particles are generated. However, in order to withstand the gas used in the semiconductor equipment, the parts must have high corrosion resistance. However, the surface hardness generally become lowered through electro-polishing. Therefore, in this study, surface hardness were experimentally observed before and after electro-polishing. Then, a method of improving hardness by preparing a nitrided layer by plasma ion nitriding treatment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.481-486
• /
• 2010

ENIG (electroless Ni immersion gold) is one of surface finishing which has been most widely used in fine pitch SMT (surface mount technology) and BGA (ball grid array) packaging process. The reliability for package bondability is mainly affected by interfacial reaction between solder and surface finishing. Since the behavior of IMC (intermetallic compound), or the interfacial reaction between Ni and solder, affects to some product reliabilities such as solderability and bondability, understanding behavior of IMC should be important issue. Thus, we studied the properties of ENIG with P contents (9 wt% and 13 wt%), where the P contents is one of main factors in formation of IMC layer. The effect of P content was discussed using the results obtained from FE-SEM(field-emission scanning electron microscope), EPMA(electron probe micro analyzer), EDS(energy dispersive spectroscopy) and Dual-FIB(focused ion beam). Especially, we observed needle type irregular IMC layer with decreasing Ni contents under high P contents (13 wt%). Also, we found how IMC layer affects to bondability with forming continuous Kirkendall voids and thick P-rich layer.