• 설비공학논문집
• /
• 제5권3호
• /
• pp.157-168
• /
• 1993

Pipe network of hot water heat supply system in an apartment house was analyzed. Flowrate and supply heat capacity of each household in which constant flowrate balancing valve is installed in a single zone system were calculated and the results were investigated. In the existing piping system, the non-uniformity of heat supply with floors due to the static pressure and temperature difference between supply main and return main can not be avoided and this tendency get intense with the increase of the height of building. The non-uniformity of heat supply can be prevented by the installation of balancing valve at each household, however if the performance of supply pump is not sufficient to overcome the energy loss due to the installation of balancing valve for constant flow rate or if the selection of the valve capacity is not adequate, the valves will may lose their controllability.

• 드라이브 ㆍ 컨트롤
• /
• 제13권4호
• /
• pp.7-13
• /
• 2016

This paper presents the meter-out and meter-in speed control characteristics of a pneumatic cylinder with relief valve type cushion device. The piston displacement and velocity are measured to investigate high speed driving performance with variation of the pressure setting in relief valve, air supply pressure, load mass, the supply and exhaust flow rate from the cylinder. Also, the internal pressures and temperatures driving pressure and cushion chamber are measured. The piston displacements and velocities of meter-out and meter-in control are compared experimentally determined data. A comparison experimental data meter-out and meter-in control show that a relief valve type cushion device is suitable for high speed pneumatic cylinders. The desired response characteristics of piston displacement and velocity are satisfactory adjust the pressure setting of a relief valve with varying system parameters such as air supply pressure, load mass and controlled flow rate.

• 한국재난정보학회 논문집
• /
• 제16권1호
• /
• pp.144-154
• /
• 2020

연구목적: 본 논문은 밸브의 누수 상태를 확인하기 위한 모니터링 시스템을 위하여 개발된 스마트 볼트의 적용성에 대한 기초 연구이다. 연구방법: 스마트 볼트에 내장된 변형률 센서와 가속도 센서를 이용하여 모의 누수 탐지 실험을 실시하였다. 연구결과: 스마트 볼트는 볼트 조임토크 기준에 부합하였으며 허용인장응력 범위 내에서 거동을 하여 상수도 체결부 적용에 부합되는 것으로 나타났다. 그리고 모의 누수 실험결과 밸브 누수 지점에선 60Hz 대역의 누수 신호가 탐지 되었으며, 메인관 누수에서는 상대적으로 고주파수 대역의 누수 신호도 탐지되었다. 결론: 모의 배관이 구속되지 않은 상태에서 전체적으로 연성진동이 이뤄진 것으로 보인다. 스마트 볼트를 통해 밸브 누수 신호의 감지에 대한 가능성을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제18권3호
• /
• pp.348-355
• /
• 2007

To grasp a feasibility of back fire control by valve overlap period, back fire limit equivalence ratio was estimated with valve overlap period which has the same supply energy and positive intake pressure as valve overlap period $300^{\circ}\;CA$. As the result, it was shown that the smaller valve overlap period has the higher back fire limit equivalence ratio under valve overlap period $300^{\circ}\;CA$ as well as VOP $0^{\circ}\;CA$. This result means that expansion of back fire equivalence ratio by decreasing valve overlap period was caused by decrease of back flow duration of flame from in-cylinder to intake port than decrease of lower supply energy.

• 한국수소및신에너지학회논문집
• /
• 제34권6호
• /
• pp.689-697
• /
• 2023

The high-pressure hydrogen valve is intended to supply hydrogen charged at high pressure in the hydrogen tank to the fuel cell stack, which decompresses high-pressure hydrogen gas to low pressure and primarily limits the excessive flow. It consists of a pilot valve, a main valve, and a excessive flow valve to operate in a wide pressure range from 2 to 70 MPa of charging pressure. The opening characteristics of the valve were confirmed by computation fluid dynamics applying the moving grid technique. The behavior of the valve was predicted by predicting the force acting on the valve over time. In addition, the difference in behavior according to supply pressure was compared.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.849-851
• /
• 2010

본 논문에서는 화초를 전문으로 관리하는 대규모 화훼단지 또는 사무실이나 가정 등에서 취미생활로 소량의 화초를 관리하고 있는 경우에, 화초에 물을 제때 공급해주지 않아서 화초가 말라죽는 것을 사전에 방지하기위한 물 공급 도우미를 제안 한다. 제안하는 시스템은 초기 연구단계로서 2개 이하의 화초에 대해서 적용한다. 습도센서를 사용해서 흙속에 존재하는 수분의 양을 측정하고, 수분의 양이 특정한 값 이하로 떨어지면 물 공급 시스템의 밸브를 자동으로 열어서 일정한 물이 공급되게 한다.

• 한국수자원학회논문집
• /
• 제52권10호
• /
• pp.719-728
• /
• 2019

상수도 관망 밸브는 평상시 관로의 유향을 변경하는 역할을 하지만, 관로 파손, 수질 문제 등 사고 발생 시 해당 구역을 격리하는데에도 이용된다. 밸브조작에 의한 구역 단수는 주변 지역의 압력 및 물 공급 성능 저하를 유발한다. 최근 안정적인 상수도 관망 물 공급을 위협하는 사고가 다양하고 빈번하게 발생하고 있으며, 이에 따라 다양한 시나리오를 고려하여 밸브 위치 결정을 하는 것이 필요하다고 할 수 있다. 따라서 본 연구에서는 밸브의 개수, 구역격리 시 물 부족량, 수리학적 거리 인자(Hydraulic Geodesic Index, HGI)를 통합한 목적함수를 개발하고, 다양한 물 부족 시나리오에 기반한 밸브 최적 위치 결정 방법론을 제안한다. 제안한 방법론은 페스카라 관망에 적용되었으며, 시나리오별로 도출된 최적 밸브 설계안의 차이점을 분석하였다. 최적 밸브 위치 탐색 과정 중 수행된 관망 수리해석은 압력 기반(Pressure Driven Analysis, PDA)으로 수행하였다. 개발된 방법론으로 도출한 최적 밸브 설계안은 기존 설계안 대비 밸브 개수가 최대 19개나 적었고, 세그먼트 격리 시 물 공급 부족량 또한 상대적으로 작았다. 수원 수두가 낮은 시나리오를 고려할수록 더 많은 밸브가 설치되었는데, 밸브 추가 설치에 따른 비용증가는 다양한 시나리오에서 물 공급 성능 향상으로 이어짐을 확인하였다. 또한, 세그먼트 격리 상황 모의를 압력 및 유량 기반 해석으로 수행한 결과를 비교하여, 밸브 최적 위치 설계 수행 시 압력 기반 해석이 필요함을 확인하였다.

• 설비공학논문집
• /
• 제26권5호
• /
• pp.218-223
• /
• 2014

Korea District heating corp. recently give an attention to combine the district heating and supply pipes as a two pipe system that are in the present system separated with room heating and warm water supply pipe, and the two pipe system is commonly applied for heating service in European countries. In the new two pipe system, only one heat source is supplied to a house and partitioned into room heating and warm water supply by household substation. So the effective distribution of supplied heat source in accordance to user intention is very important. This paper presents the development and performance test of three-way proportional control valve for a combined heat source system in district heating. The proposed valve is controlled to partition heat source into two different directions : hot water distributor for space heating and household substation for warm water supply in response to the pressure drops of tap water caused by the user. The performance investigation is shown within 3% of error compared to the theoretical model of the three-way proportional valve and its controllability is verified.

• 유공압시스템학회논문집
• /
• 제5권4호
• /
• pp.10-16
• /
• 2008

In this paper, the authors benchmark a servo valve model for the fuel supply system of Auxiliary Power Unit (APU) in the KHP helicopter. This valve is directly driven with a torque motor, and the size of small gap controlled by a flapper can make change of flow rate under given pressure drop between inlet and outlet. CFD analyses using a commercial code, ANSYS-CFX 10 are performed for the series of three-dimensional models at various openness conditions. The computational results on simplified models show that CFD can play a fine roll in the design of flow path as well as in the estimation of flow force due to its precision and good repeatability. Consequently, the CFD analysis helps valve designers to understand its flow characteristics from the basis of physical fundamentals.

• 대한기계학회논문집
• /
• 제1권2호
• /
• pp.65-72
• /
• 1977

Major problems in the design and use of refief valve are (a) chattering because of instability, (b) excessive pressure differential which makes the valves crack far below maximum pressure diminishing useful flow in the system. In this study, A magnet-coupled relief valve is investigated theoretically and experimentally in order to improve the performance of a conventional direct type reliefvalve. A theory is developed to predict the performance, response, and stability of the magnet-coupled valve taking into account the delivery line response. In the experiment, a typical magnet-coupled relief valve is designed on the basis of the analytical results; the discharge rates are measured varying the supply pressure, and both the pressure-time curves and valve displacament-time curves are recorded providing the supply pressures greater than the setting pressure. The measured override characteristic curves are then compared with those of conventional pilot type and direct type releif valves. It is showm that the excessive pressure differential of a magnet-coupled relief valve becomes less than that of a conventional direct type valve. It is also shown that the most important chatacteristic of a magnet-coupled relief valve is to eliminate valve chattering due to instability regardless of the magnitude of setting pressures and discharge rates, which suggests wide applications of the idea of the use of a magnet in the design of hydraulic valves.