• Progress in Superconductivity and Cryogenics
• /
• v.14 no.2
• /
• pp.32-35
• /
• 2012

The objective of the present work is to develop a precise instrument for measuring the thermal property of insulating material over a temperature range from 30 K to near room temperature by utilizing a cryocooler. The instrument consists of two thermal links, a test sample, heat sink, heat source and vacuum vessel. The cold head of the cryocooler as a heat sink is thermally anchored to the thermal link and used to bring the apparatus to a desired temperature in a vacuum chamber. An electric heater as a heat source is placed in the middle of test sample for generating uniform heat flux. The entire apparatus is covered by thermal shields and wrapped in multi-layer insulation to minimize thermal radiation in a vacuum chamber. For a supplied heat flux the temperature distribution in the insulating material is measured in steady and transient state. The thermal conductivity of insulating material is measured from temperature difference for a given heat flux. In addition, the specific heat of insulating material is obtained by solving one-dimensional heat diffusion equation.

• Nuclear Engineering and Technology
• /
• v.31 no.1
• /
• pp.116-132
• /
• 1999

This study is intended to analyze the requirements of a buffer material that is one of the major components of the engineered barriers in a high-level radioactive waste repository. The characteristics of potential materials for the buffer in the repository were analyzed and a candidate material was selected. And, based on the current knowledge and the information from various sources, the requirements of a buffer material were evaluated. Finally its quantitative functional criteria on the generic viewpoint has been recommended to be supplied as a guideline for the development of the reference disposal concept and the related buffer material in Korea. The criteria are composed of seven major items, such as hydraulic conductivity, retardation capacity, swelling potential and swelling pressure, thermal conductivity, longevity, organic matter content, and mechanical properties.

• Tribology and Lubricants
• /
• v.36 no.3
• /
• pp.153-160
• /
• 2020

In this paper, we present a hydrostatic bearing design and rotordynamic analysis of a pump-and-drive turbine module for a 250-kW supercritical CO₂ cycle application. The pump-and-drive turbine module consists of the pump and turbine wheel, assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 21,000 rpm and the rated power is 143 kW. For the bearing operation, we use high-pressure CO₂ as the lubricant, which is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various orifice diameters, and then select the diameter that provides the maximum bearing stiffness. We also conduct a rotordynamic analysis based on the design parameters of the pump-and-drive turbine module. The predicted Campbell diagram shows that there is no critical speed below the rated speed, owing to the high stiffness of the bearings. Furthermore, the predicted damping ratio indicates that there is no unstable mode. We conduct the operating tests for the pump and drive turbine modules within the supercritical CO₂ cycle test loop. The pressurized CO₂, at a temperature of 136℃, is supplied to the turbine and we monitor the shaft vibration during the test. The test results show that there is no critical speed below the rated speed, and the shaft vibration is controlled to below 3 ㎛.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.155-160
• /
• 2018

The materials used for 3D printing are mainly plastic and metal. These materials are usually used in the powdered form. In order to improve the surface roughness of a manufactured product, these powders should consist of small uniform spherical particles. However, the powdered forms are sold at a considerably higher price than bulk or wired materials. When a wire-type material is used instead of a powder, we can supply a relatively large amount of the material at one time as well as reduce the cost. Moreover, the use of this form of the material will increase the process efficiency. This paper deals with the technology required to feed a wire material in front of the tool movement and discusses the examples used for the verification.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.11-20
• /
• 2001

This laboratory study examined the impact of free chlorine residual and pipe material on the formation of biofilm in drinking water distribution pipe surfaces. Result of heterotrophic plate counts(HPC) of the biofilm in the tap water-supplied reactor averaged $2.17{\times}10^5CFU/cm^2$ on PVC and $2.43{\times}10^5CFU/cm^2$ on STS 316, respectively. HPCs on the surface exposed to the tap water containing 0.2mg/L of free chlorinne residual averaged $4.24{\times}10^4CFU/cm^2$ on PVC and $6.54{\times}10^4CFU/cm^2$ on STS 316, respectively. Average of HPC/Total direct counts in the tap water-supplied reactor ranged from 1.08%(PVC) to 1.26%(STS 316) and from 0.38%(PVC) to 0.65%(STS 316) in the reactor supplemented with disinfectant, respectively. No correlation was observed between disinfectant addition and biofilm density. With regard to the biofilm formation, little difference existed between PVC and STS 316. Yellow and red pigmented bacteria were the dominant expressions in bulk fluid, whereas non-pigmented bacteria were found dominant in the biofilm. Pink/red pigmented bacteria were found to be facultative anaerobic, while yellow pigmented bacteria and non-pigmented bacteria were found to be obligate aerobic.

• Tribology and Lubricants
• /
• v.40 no.2
• /
• pp.39-46
• /
• 2024

The Morton effect (ME) is an instability phenomenon occurring in rotating machineries supported by fluid film bearings and is induced by the thermal deformation of the overhung mass, which is a part of the rotating shaft. Herein, we describe the ME during the high-speed balancing test of a 20 MW class steam turbine. Additionally, to predict the rotating speed at which the ME occurs, we apply the sensitivity vector theory for the steam turbine. During the operation of the steam turbine, we observe a continuous increase in vibration and hysteresis near the rated speed, which is typical of the ME. Increasing the temperature of the lubricating oil supplied to the bearings from 40 to 60℃ suppresses the occurrence of the ME. The rotordynamic analysis for the steam turbine suggests the existence of a mode in which the overhung mass undergoes significant deformation near the rated speed, and we presume that such a mode will increase the occurrence of the ME. The predicted rotating speed of ME occurrence, obtained through the sensitivity vector method, correlates with the test results. Moreover, increasing the temperature of the supplied lubricating oil mitigates the occurrence of ME by reducing the sensitivity between the temperature deviation vector and unbalance mass vector.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.643-644
• /
• 2005

New methods of nano-sized material and composite coating preparations have been considered on the base of mathematical model of abrasion-reaction interaction of milling and grinding bodies in planetary centrifugal mill. The essence of the method is the abrasive and oxidative wear of the milling bodies and amorphous (better inert) additives. Interactions between them has been supplied the necessary impulse of pressure and temperature on the impact-frictional contacts and promoted chemical processes. The offered method can find application for such processing as sintering and geological minerals opening.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.141-144
• /
• 2004

A QVGA active-matrix backplane is produced on a 25${\mu}m$ thin plastic substrate. A 4-mask photolithographic process is used. The insulator layer and the semiconductor layer are organic material processed from solution. This backplane is combined with the electrophoretic display effect supplied by SiPix and E ink, resulting in an electronic paper display with a thickness of only 100${\mu}m$. This is world's thinnest active-matrix display ever made.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.456-466
• /
• 1996

Electrostatic spraying is needed for today's sustainable farming. An electrostatic spraying nozzle was developed and its spraying performance was evaluated. High voltages of 15㎸, 20㎸, and 25㎸ were supplied for the electrostatic electrode. Artificial and real apple targets were used for the spraying experiments. Insulated material was used around the electrode to protect the loss of electrostatic effect. Three angles (0, 45, 90 degree) of spraying direction were used for the spraying test. The performance of electrostatic spraying was improved from 204.5% upto 429.2% on the apple targets.

• Journal of the Korean Chemical Society
• /
• v.38 no.10
• /
• pp.726-733
• /
• 1994

Supercritical fluid extraction (SFE) followed by gas chromatographic separation and mass spectrometric (MS) detection were used in rapid analysis of polycyclic aromatic hydrocarbons (PAH's) in air particulate material extracted for 30 min with 10 ml of supercritical $N_2O$ without another sample preparation step. Two samples, urban dust in Seoul area and a certified air particulate reference material 1649 supplied by the NBS (National Bureau of Standards), were processed for the purpose of evaluating extraction and analysis methods. As a result, the quantitative recovery of PAH's in the SFE method was relatively lower than conventional organic solvent extraction methods, but reproducibility was resonable, and analysis time was reduced remarkably. The method has proved to be suitable for monitoring of PAH's in air particulate material.