• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.390-390
• /
• 2010

Superconducting proximity effects of Nb/Si(111) were investigated with scanning tunneling microscopy(STM) and scanning tunneling spectroscopy(STS). A highly-doped($0.002\;{\omega}{\diamondsuit}cm$) Si wafer pieces were used as substrate and Nb source was thermally evaporated onto the atomically clean silicon substrate. The temperature of the silicon sample was held at $600^{\circ}C$ during the niobium deposition. And the sample was annealed at $600^{\circ}C$ for 30 minutes additionally. Volmer-Weber growth mode is preferred in Nb/Si(111) at the sample temperature of $600^{\circ}C$. With proper temperature and annealing time, we can obtain Nb islands of lateral size larger than Nb coherence length(~38nm). And outside of the islands, bare Si($7{\times}7$) reconstructed surface is exposed due to the Volmer-Weber Growth mode. STS measurement at 5.6K showed that Nb island have BCS-like superconducting gap of about 2mV around the Fermi level and the critical temperature is calculated to be as low as 6.1K, which is lower than that of bulk niobium, 9.5K. This reduced value of superconducting energy gap indicates suppression of superconductivity in nanostructures. Moreover, the superconducting state is extended out of the Nb island, over to bare Si surface, due to the superconducting proximity effect. Spatially-resolved scanning tunneling spectroscopy(SR-STS) data taken over the inside and outside of the niobium island shows gradually reduced superconducting gap.

• Progress in Superconductivity
• /
• 제13권2호
• /
• pp.122-126
• /
• 2011

Superconducting $MgB_2$ thin films were fabricated by using a novel aerosol deposition technique wherein the pre-reacted powder is directly transformed into respective thin film. The formed thin films were characterized by X-ray diffraction technique and FE-SEM to understand its structure and morphology and the superconducting behavior has been characterized with the four probe resistivity measurement. The as-deposited thin films were formed into the frustrated amorphous structure, which were relaxed on the further heat treatment at $900^{\circ}C$ for 3 hrs. The relaxed amorphous $MgB_2$ thin films showed a comparatively high superconducting onset at about 38 K.

• 분석과학
• /
• 제5권2호
• /
• pp.223-228
• /
• 1992

초산염(acetate)을 출발원료로 하여 $Bi_2Sr_2Ca_2Cu_3Oy$계 단일상 고온초전도체를 합성하려 하였으며 그 초전도상의 형성과정을 초전도전이온도 $T_c$ 및 전하나르게 농도와의 상관관계로부터 설명하고자 하였다. 초전도전이온도 $T_c$는 전기저항밀도 및 자화율을 측정하여 결정하였다. 시료로는 상기의 초전도체 출발조성물의 하소분말에 대해 $850^{\circ}C$, $860^{\circ}C$, 그리고 $870^{\circ}C$에서 40시간 동안 공기 중 열처리한 것을 이용하였다. 전하나르게농도는 홀계수를 측정하여 구하였다. 열처리과정 중의 초전도체 형성과정을 세라믹벌크내에 형성된 초전도체의 양 및 전하나르게농도 분포의 상관관계로부터 설명하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권6호
• /
• pp.286-290
• /
• 2003

The high temperature superconducting bulk can be used as the bearing of induction motors. This paper presents the fabrication and test results of an induction motor with superconducting bearings using HTS bulks. The bearing had eight hexahedron type YBCO bulks. Height, width and thickness of the HTS bulk were 30mm, 30mm and 10mm, respectively. Single phase induction motor was used to drive the shaft made of aluminum and the rotor of a conventional induction motor. To estimate the performance of the HTS bulk magnetic bearing, no load test, load test and Impact test were carried out. Load tests were performed by using air resistance caused by the shaft-mounted thin cylinder with buckets. Impact tests by axial direction and vertical direction impact showed that the vibration of the shaft gradually decayed. The induction motor with HTS bulk magnetic bearing rotated silently and smoothly throughout the tests. According to the test results, conventional bearings can be replaced with superconducting magnetic bearings made of HTS bulks.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권1호
• /
• pp.1-5
• /
• 2004

Long length of Bi-2223/Ag superconducting wives were fabricated by stacking and drawing process with advanced heat-treatment schedules. Intermediate annealing was carried out to increase the homogeneity and uniformity of the superconducting filaments embedded in the silver matrix. Phase modification from tetragonal to orthorhombic Bi-2212 by pre heat treatment(PHT) was executed to improve the texture and phase transformation of Bi-2223. Drawing stress was measured to predict the sausaging and stress limit. Rolling Parameters such as thickness. width and winding tension were investigated to roll the tape with uniformity. 1 km length of Bi-2223/Ag superconducting wires were fabricated without any breakage. Critical current (Je) of 270 m length of superconducting tapes was measured over than $70 A/cm^2$ continuously after final sintering.

• Bulletin of the Korean Chemical Society
• /
• 제23권9호
• /
• pp.1304-1323
• /
• 2002

Superconducting BiSrCaCu(Ni)O ceramicss have been prepared by the gel method using an aqueous solution containing a tartaric acid. The aqueous solution of metal salts was concentrated without precipitation. The precursor so prepared was homogeneou s and calcined at $825^{\circ}C$ for 24 h to produce superconducting phase. The thermal decomposition of gels, the formation of superconducting phase, and their ceramic microstructure were studied using IR, TGA, XRD, resistance measurements, and SEM. This method is highly reproducible and leads to powders with excellent homogeneity and small particle size for easy sinterability. The nickel dopant substituting for Cu gives rise to the gradual decrease of the Tc. Phase pure 2212 ceramics were obtained at 825 $^{\circ}C$ for 24 h. SEM pictures showed that liquid phase was formed when the samples were sintered temperatures higher than 825 $^{\circ}C$.

• 한국전기전자재료학회논문지
• /
• 제29권10호
• /
• pp.630-634
• /
• 2016

In this paper, we analyzed the power consumption and the accumulated energy in HTSC (high-TC superconducting elements) according to the resistance of HTSC element and the winding current of transformer type SFCL (superconducting fault current limiter) using double quench. For the analysis, two different inductances of the one secondary winding among two secondary windings comprising the transformer type SFCL were selected and the short-circuit tests were carried out. The consumed power and the accumulated energy in HTSC element connected into the secondary winding with larger inductance were analyzed to be larger compared to the one connected into the secondary winding with lower inductance.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권6호
• /
• pp.368-371
• /
• 2004

The quench current characteristics of the superconducting solenoids with large diameter were experimentally investigated. Three solenoids with inside diameter of 450mm were fabricated with different tensions and different types of epoxy applications. The quench current of each solenoid was measured according to the various ramping rates of current. The highest quench current was obtained in the solenoid impregnated with epoxy after winding with tension of 20 percents of the yield strength of the superconducting wire. It was found that the quench currents were almost independent of the ramp rate of current. From the results, although the training effect in the solenoid appeared with epoxy impregnation, the quench current of solenoid impregnated with epoxy was higher than that without epoxy impregnated The test results are presented and discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.329-331
• /
• 1995

Laser ablation was used to fabricate superconducting $YBa_2Cu_3O_{7-x}$ (YBCO) thin films on metallic substrates with an YSZ buffer layer. An ArF excimer laser with an wavelength of 193 nm was used to deposit both YSZ buffer layer and superconducting thin film. The characterizations of thin films were performed and compared. With a 200 nm YSZ buffer layer, c-axis orientation and $T_c$=85 K were obtained for a 200 nm-thick YBCO film.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 하계학술대회 논문집
• /
• pp.36-40
• /
• 1990

According to the rapid growth of transmission power, fault current level approaches to the maximum capacity of circuit breaker. This paper has been proposed a superconducting current limiter (SCL) to reduce the fault current to appropriate level. Superconductor for SCL has been examined and design criterion of each triggering method has been shown. Superconducting current limiter was fabricated using thin film and switching characteristics were shown, where thermal and current triggering were adopted.