• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.1
• /
• pp.46-53
• /
• 2023

In this paper, we evaluated the flexural performance of three types of reinforced concrete beams (SHCC-RB, SHCC-SB, SHCC-FRP) strengthened with ordinary steel rebar, very high strength (super strength) rebar, and FRP bars together with strain-hardening cement composite (SHCC). For this purpose, a series of beam specimens were manufactured and four-point load bending experiments were performed. As a result of the experiment, all specimens strengthened with SHCC exhibited tightly controlled flexural microcrakcs with the crack width of less than 100 ㎛. This is mostly due to the material properties of SHCC showing tensile strain hardening properties with multiple microcracks under uniaxial tension. The specimen SHCC-FRP showed lower initial cracking moment and yield flexural strength than SHCC-RB, whereas the maximum flexural strength of SHCC-FRP was superior to that of SHCC-RC. This is because the tensile strength of FRP bars is higher than that of ordinary steel reabr. The initial cracking moment of the beam specimen SHCC-SB was similar to that of SHCC-RB, but the yield flexural strength and maximum flexural strength of SHCC-SB were evaluated to be the highest.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.1
• /
• pp.25-33
• /
• 2015

In this study, initial crack index was evaluated by FEM analysis to find the crack propagation from hydration heat in precast concrete. As results, as the usage of hardening accelerator increased, initial compressive strength increased and setting time was shortened. Additionally, as amounts of hardening accelerators increased, the central temperature of concrete increased and the time to reach the highest temperature was shortened. It was demonstrated that the hardening accelerators accelerated the hydration reaction of cement, and caused the increase of hydration heat within the short period of time. Furthermore, the crack index for evaluating the heat level was performed by FEM. As results, there was no problem about the cracks, despite of the growth of initial high hydration heat. This is because of the increased tensile strength that is large enough to sustain the thermally induced-stress.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.5
• /
• pp.569-578
• /
• 2013

In a super-tall building construction, thick and large-sized embed plates are usually used to connect mega structural steel members to RC core wall or columns by welding a gusset plate on the face of the embed plate with T-shape. A large amount of heat input accumulated by weld passes causes the plates to expand or deform. In addition, the temperature of concrete around the plates also could be increased. Consequently, cracks and spalls occur on the concrete surface. In this study, the effect of weld heat on embed plates and 80MPa high strength concrete is investigated by considering weld position (2G and 3G position), edge distance, concrete curing time, etc. Measured temperature of the embed plates was compared with the transient thermal analysis results. Finally, push-out tests were performed to verify and compare the shear studs capacity of the embed plate with design requirement. Test result shows that the shear capacity of the plate is reduced by 14%-19% due to the weld heat effect and increased as the concrete curing time is longer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.269-275
• /
• 2019

As the national industry is developing gradually due to the expansion of the economic scale, the construction of large and super high-rise structures for building social infrastructure has been increasing, and studies have been conducted actively to transmit the large loads at the upper portion to the lower bedrock. In this study, the PHC was extended to an ultra-high strength PHC, which increased the concrete compressive strength of the PHC from the conventional 80 MPa to 110 MPa, and the PHC, which extended the tip of the pile. After construction with the driving method and injected pile method, the tendency of the bearing capacity was tested through a load test. Measurements of the bearing capacity of the extended PHC using the pile driving method revealed the main surface friction force to be smaller than that of the general PHC, and the stet-up effect was also insignificant. On the other hand, the effect of the friction force on the ground surface when the injected pile method was applied is expected to increase the bearing capacity when the gap between the main surface and the ground is wide and the cement paste is filled tightly. In addition, the ultrahigh strength PHC showed higher bearing capacity than the conventional PHC, and the permissible pile stress was less than 60%. Therefore, it is possible to reduce the number of piles and reduce the construction cost and effect of shortening the length of the pile by designing the tip of the pile on the ground with the intensity of soft rock as a method for utilizing the increased strength of the ultra-high strength PHC.

• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.323-331
• /
• 2012

This paper presents a new strengthening method on concrete column against seismic loads for structural performance tests. An X-bracing using high performance carbon fiber threads called the "Carbon fiber anchor X-bracing system" is used to connect RC frames internally. The carbon fiber sheet is wrapped around the column to fix the top and bottom of the column after Super anchor was installed by drilling hole on the column. The structural performance was evaluated experimentally and analytically. Two types of columns specimens were made; flexure fracture scaled model and shear fracture scaled model. For the performance evaluation, cyclic loading tests were conducted on moment and shear resisting columns with and without X bracing. Test results confirmed that the bracing system installed on RC columns enhanced the strength capacity and provided adequate ductility.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.1
• /
• pp.13-20
• /
• 2005

The effects of pectin on obesity was studied using 3T3-L1 pre-adipocytes and rats fed 20% high fat diets. The concentration of leptin released from 3T3-L1 adipocytes in the presence of pectin was significantly decreased by 85% compared to that of the control (p<0.05), however, glycerol concentration was not changed. These data indicate that pectin seems to inhibit lipids accumulation in the adipocytes rather than enhance the lipolytic activity. Forty Sprague Dawley rats were fed 20% high fat diet for 8 weeks to induce obesity and then divided equally into four groups. Experimental groups were normal diet group (ND), high fat diet group (HFD), HDF with 10% pectin group (HFP10), and HDF with 20% pectin group (HFP20). Diet for the each group was prepared to be iso-caloric following AIN-76 guideline. After obesity was induced, rats were placed on an restricted diet for 9 weeks. The body weight of HFD increased 50% (p<0.05) compared to the ND, while it was decreased by 12% and 16% for HFP10 and HFP20, respectively (p<0.05). The relative amount of visceral fats for HFDl0 and HFD20 were decreased by 45% and 59% compared to that of HDF (130%), respectively (p<0.05). Pectin seems to have a greater effect on reducing visceral fats accumulation than weight reduction. Significantly increased level of triglyceride, total cholesterol or LDL-cholesterol in the plasma of HFD was returned to the normal or even below the normal by pectin diet, while the level of HDL-cholesterol increased. Lipid lowering effect was also observed in the liver and heart. These effects of pectin were dosedependent. In conclusion, the beneficial effect of pectin on the obesity was observed from cell culture experiment and animal study in terms of inhibiting the accumulation of lipids in the adipocytes.