• 한국가스학회지
• /
• 제26권2호
• /
• pp.9-13
• /
• 2022

벨트나 체인을 이용한 감속기는 간단한 장치이긴 하지만 공간을 많이 차지하여 공간상의 제약이 있기 때문에 전동휠체어 구동부에는 부적합하다. 하지만 유성기어형태의 감속기는 동일 축에서 감속이 이루어지기 때문에 부피를 작게 할 수 있어 공간의 제약이 벨트나 체인형태의 감속기보다 덜하다. 따라서 본 연구에서는 수·전동전환이 가능한 휠체어의 구동부에 대한 연구를 통하여 유성기어형태를 이용한 감속기로 큰 추진력을 얻을 수 있는 구동부를 개발하였다. 그에 따라 감속기에 적용되는 유성기어의 치형을 Kisssoft 프로그램을 이용하여 설계를 진행하였다. 또한 기존 휠체어 바퀴에 적용 가능하도록 구동부의 설계를 진행하였고, 구동부의 수·전동 전환원리 및 작동원리에 대한 메커니즘의 최적화를 진행하였다. 연구내용을 토대로 하나의 선기어와 2개의 유성기어, 하나의 링기어를 갖는 유성기어 형태의 휠체어 감속기 구동부의 최종 설계 및 제작을 진행하였다.

• International journal of advanced smart convergence
• /
• 제9권3호
• /
• pp.199-206
• /
• 2020

A wheelchair is an essential rehabilitation assistant device for the movement of paraplegia patients and generally paralyzed patients who cannot walk normally. In particular, the applicability of the manual/motorized wheelchair is gradually increasing. Until now, decelerators using belt, chain and worm gears, etc have been widely used. However, a decelerator takes a large space although it is a simple device and thus is not ideal for the driving part of manual/motorized wheelchair. For these reasons, in this study we developed a driving part producing a large driving force through a decelerator using planetary gears rather than conventional worm gear-based decelerator. We designed the tooth profile of the planetary gears for decelerator using Kisssoft program, In addition, we designed the driving part so as to apply it to the wheels of conventional wheelchairs, and then optimized the mechanism for the principles of manual/motorized transposition of the driving part and the operational principles. Based on the results of this study, we finally designed and manufactured a driving part for wheelchair decelerator in the form of planetary gears with 1 sun gear, 2 planetary gears and 1 ring gear.

• 한국소음진동공학회논문집
• /
• 제25권7호
• /
• pp.470-480
• /
• 2015

As the railway noise guideline of the Ministry of Environment after 2017 is strictly enforced, the noise level at stationary condition of urban railway is demanding the reduction about 2 dB(A). And the noise level at running condition is reduced by 6 dB(A) at 80 km/h. Therefore, the devices that causes noise shall arrange for the improvement plan of noise reduction for each device. In this paper, we carried out a technical review of the driving gear used to drive the vehicle from a variety of noise-induced equipment of a urban railway. Analyze the causes of the current noise levels and noise cause about the driving gear used in current urban railway and this study analyzes the noise level and noise cause the drive gear being used in the current urban railway. Finally, in this paper proposes a scheme for reducing the noise that can be designed to reduce the noise with considering the noise cause analysis.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.605-609
• /
• 2010

본 논문은 유성기어를 적용한 터보펌프의 개념설계에 대하여 기술하였다. 발사체시스템에서는 무게가 가장 중요한 설계인자 중 하나이다. 케로신 혹은 메탄을 연료로 사용하는 터보펌프의 경우 통상 시스템의 간단성 때문에 1축(혹은 동축) 형식이 사용된다. 이 경우 단점은 산화제펌프와 연료펌프의 회전수가 서로 최적이 아닌 상태에서 작동하게 되는 것이다. 각 펌프가 최적 회전수에서 작동하고 또한 증가된 회전속도로 부터 부품의 효율 증대와 무게이득을 최대화하기 위해서는 터보펌프에 유성기어를 적용하는 것이 최선의 방법이 아닐까 판단된다. 본 논문에서는 유성기어를 도입한 터보펌프의 개념설계와 가능성에 대해 제안하였다.

• 한국추진공학회지
• /
• 제15권3호
• /
• pp.58-63
• /
• 2011

본 논문은 유성기어를 적용한 터보펌프의 개념설계에 대하여 기술하였다. 발사체시스템에서는 무게가 가장 중요한 설계인자 중 하나이다. 케로신 혹은 메탄을 연료로 사용하는 터보펌프의 경우 통상 시스템의 간단성 때문에 1축(혹은 동축) 형식이 사용된다. 이 경우 단점은 산화제펌프와 연료펌프의 회전수가 서로 최적이 아닌 상태에서 작동하게 되는 것이다. 각 펌프가 최적 회전수에서 작동하고 또한 증가된 회전속도로 부터 부품의 효율 증대와 무게이득을 최대화하기 위해서는 터보펌프에 유성기어를 적용하는 것이 최선의 방법으로 판단된다. 본 논문에서는 유성기어를 도입한 터보펌프의 개념설계를 수행하여 유성기어의 적용가능성을 제시하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.15-21
• /
• 2019

In this study, the maximum system efficiency of the electro-hydrostatic actuators was experimentally investigated, where small size external gear pumps with volumetric displacement under 1.3 cc/rev were combined with a 400W servomotor as the prime mover. Since the efficiency data of the servomotor, gear pumps and hydraulic cylinder were not provided by the suppliers, experimental apparatuses for their efficiency measurement were extra built up. When a gear pump with a volumetric displacement of 1.27cc/rev was used on an electro-hydrostatic actuator system, the maximum system efficiency was not higher than 70%. This was because the most effective operation ranges of the motor and pump did not coincide each other. In order to match their operation ranges as one of the most crucial design factors, a speed reduction mechanism can be used, such as a timing belt. It was shown in the study that the maximum system efficiency could be increased from 70% to 76% in that way.

• 농업과학연구
• /
• 제43권4호
• /
• pp.650-655
• /
• 2016

Gears are components of transmission which transmit the power of an engine to a machine and offer numerous speed ratios, a compact structure, and high efficiency of power transmission. Gear train design in the automotive industry uses simulation software. However, PTO (Power Take-Off) gear design for agricultural applications uses the empirical method because of the wide range of load fluctuations in agricultural fields. The PTO is an important part of agricultural tractors which transmits the power to various tractor implements. Therefore, a simulation was essential to the optimal design of the PTO. When the PTO gear is optimally designed, there are many advantages such as low cost, reduced size, and light weight. In this study, we conducted the bending and contact safety factor simulation for the PTO gear of an agricultural tractor. The bending and contact safety factors were calculated on ISO 6336 : 2006 by decreasing the face widths of the PTO pinion and wheel gear from 18 mm at an interval of 1 mm. The safety factor of the PTO gear decreased as the face width decreased. The contact safety factors of the pinion and wheel gear were 1.45 and 1.53, respectively, when the face width was 18 mm. The simulation results showed that the face width of the PTO gear should be greater than 9 mm to maintain the bending and contact safety factors higher than 1. It would be possible to reduce the weight of the PTO gear for different uses and working conditions. This study suggests that the possibility of designing an optimal PTO gear decreases as its face width decreases.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.712-717
• /
• 2007

This study deals with the TE(Transmission Error) of gear tooth profile by modifying a profile and lead of a surface of tooth. First, we experimentally confirmed that the TE is a synthesis of the sliding velocity between both gears. Since various types of TE appear in the experiments, we introduced definition of transmission error and the optimism design by modifying a surface parameters. The test stand's performance is then evaluated through a series of multiple torque transmission error tests. Comparisons are made between data recorded before and after the test stand's redesign, and subsequently repeatability studies are performed to verify the veracity of the measured data. Finally, the experimental results are compared to the analytical predictions of two different gear analysis programs.

• 대한기계학회논문집A
• /
• 제27권9호
• /
• pp.1597-1606
• /
• 2003

Static analysis using hybrid finite element(FE) method has been applied to characterize the influence of position, runout and thickness errors of the sun, ring and planet on the bearing forces and critical tooth stress. Some guidelines for tolerance control to manage critical stress and bearing forces are deduced from the results. Carrier indexing error planet assembly and planet tooth thickness error are most critical to reduce planet bearing force and maximize load sharing as well as to reduce critical stresses. Sun and carrier bearing forces due to errors increase several times more than those of normal condition.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권11호
• /
• pp.646-654
• /
• 1999

This paper deals with PWM patterns for harmonic reduction in inverter fed traction motors and the gear changing techniques for the variable speed drive of traction motor. GTOs are used as switching device of inverter because traction motor is a large load. To derive PWM rattern which can minimize the harmonics with the limited switching frequency, the output current and torque characteristic of SPWM and SHE PWM was analyzed. GTO inverter used for traction motor drive includes harmonics in the output current and torque by the limitation of switching frequency. However, the hybrid PWM method that adopt SPWM in the range of low frequency and SHE PWM in upper frequency range can achieve less harmonic characteristics in GTO inverters. If the traction motor is driven in variable speed by the proposed PWM pattern, 7 times of gear changing is needed. At the instant of the mode change, magnetic flux and torque may be altered and the large current flow. To reduce such an undesirable transient behavior, it is also presented the technique for the gear changing of inverter fed traction motor drive operated with the hybrid PWM. The results are verified by simulations and experiments.