• Corrosion Science and Technology
• /
• v.22 no.3
• /
• pp.201-213
• /
• 2023

Corrosion management of an aircraft and its engine relies on rinsing and cleaning using tap water. Few studies have reported effects of tap water species on corrosion behaviors of structural materials. In this study, a series of experiments were conducted based on the design of experiment. Solutions with different levels of chloride and sulfate ions were prepared using a full factorial design. Two structural materials (aluminum alloy and steel) were used for an alternate immersion test. Weight loss was then measured. In addition, a silver specimen was utilized as a sensor for chloride deposition measurement. The silver specimen was examined using the electrochemical reduction method, XPS, and SEM-EDS. Surface analysis revealed that levels of chloride and sulfate ions were sufficient for the formation of silver chloride and silver surface. Statistical analysis of weight loss and chloride deposition rate showed significant differences in measured values. Concentration of chloride ions greatly affected corrosion behaviors of structural materials. Sulfate ion hindered the adsorption reaction. These results emphasize the importance of controlling ion concentration of tap water used for cleaning and rinsing an aircraft.

• Geomechanics and Engineering
• /
• v.16 no.4
• /
• pp.375-384
• /
• 2018

Unconfined compressive strength (UCS) of high plasticity clayey soil mixed with 5 and 10 % of Portland cement and four chemical agents such as sodium hexametaphosphate, aluminum sulfate, sodium carbonate, and sodium silicate with 0, 5, 10, and 20% concentrations was comparatively evaluated. The individual and combined effects of the cement and chemical agents on the UCS of the soil mixture were investigated. The strength of the soil-cement mixture generally increases with increasing the cement content. However, if the chemical agent is added to the mixture, the strength of the cement-chemical agent-soil mixture tends to vary depending on the type and the amount of the chemical agent. At low concentrations of 5% of aluminum sulfate and 5% and 10% of sodium carbonate, the average UCS of the cement-chemical agent-soil mixture slightly increased compared to pure clay due to increasing the flocculation of the clay in the mixture. However, at high concentrations (20%) of all chemical agents, the UCS significantly decreased compared to the pure clay and clay-cement mixtures. In the case of high cement content, the rate of UCS reduction is the highest among all cement-chemical agent-soil mixtures, which is more than three times higher in comparison to the soil-chemical agent mixtures without cement. Therefore, in the mixture with high cement (> 10%), the reduction of the USC is very sensitive when the chemical agent is added.

• Korean Journal of Environmental Agriculture
• /
• v.26 no.2
• /
• pp.131-140
• /
• 2007

Phospho-gypsum a primary waste by-product in phosphate fertilizer manufacturing industry and a potential source of electron acceptors, such as mainly of sulfate and a trace amount of iron and manganese oxides, was selected as soil amendment for reducing methane $(CH_4)$ emissions during rice cultivation. The selected amendment was added into potted soils at the rate of 0, 2, 10, and 20 Mg $ha^{-1}$ before rice transplanting. $CH_4$ flux from the potted soil with rice plant was measured along with soil Eh and floodwater pH during the rice cultivation period. $CH_4$ emission rates measured by closed chamber method decreased with increasing levels of phospho-gypsum application, but rice yield markedly increased up to 10 Mg $ha^{-1}$ of the amendment. At this amendment level, total $CH_4$ emissions were reduced by 24% along with 15% rice grain yield increment over the control. The decrease in total $CH_4$ emission may be attributed due to shifting of electron flow from methanogenesis to sulfate reduction under anaerobic soil conditions.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.15 no.4
• /
• pp.131-137
• /
• 2007

In this study, the biodegradation test on lignocellulose under sulfate reducing conditions was carried out. In particular, the interaction between cellulose and lignin was investigated with various g-cellulose/g-lignin (C/L) ratios: 42.15, 4.59, 2.51, 1.14 and 0.7. It was shown that the rate of cellulose degradation decreased in proportion to the lignin content. Assuming first order degradation kinetics, the consequences of competitive inhibition were graphically shown for different C/L ratios. The relation between cellulose reduction rate and C/L ratio was expressed by logarithm function with a determination coefficient of 0.97. Lignocellulose reduction rate was also described as a logarithm function of C/L ratio showing a inhibition effect by lignin. In the mean time, the rate of lignin decomposition was higher at C/L ratio of 2.51 and 1.14 compared with C/L ratios of 4.59 and 0.7, indicating that excessive extra carbon source is not appropriate for lignin biodegradation.

• Journal of the Mineralogical Society of Korea
• /
• v.24 no.3
• /
• pp.217-224
• /
• 2011

Removal of dissolved selenium by D. michiganensis, a iron-reducing bacterium, and effects of dissolved metal elements such as iron, sulfate, and copper were investigated. Selenide that was reduced from selenite (2 mM) by D. michiganensis was gradually removed from the aqueous medium. As the reduced selenide was combined with aqueous iron, it was precipitated as a nanoparticulate iron-selenide. Sulfate and copper negatively affected the microbial selenite reduction, and the copper was especially toxic to the bacterium, inhibiting a microbial removal of dissolved selenite. These results show that it should be carefully biotreated for a selenium-contaminated site considering in situ sulfate or copper distribution and concentration. Consequently, the formation of iron-selenide by bacteria will be an important measure for preventing a long-distance migration of selenium in the subsurface environments.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.415-423
• /
• 1996

Hydrogen reduction technique was used to form the nickel layer onto alumina powders in nickel sulfate solutions. The reduction rate and precipitation states of nickel ions were investigated at various experimental conditions such as hydrogen pressure, temperature, $PdCl_{2}$ addition, particle size, and so on. Uniformly nickel coated alumina composite powders were obtained at such condition as reduction temperature of $165^{\circ}C$, hydrogen pressure of 300 psi, and $PdCl_{2}$ amount of $2\;mg/\ell$.

• Journal of Powder Materials
• /
• v.26 no.4
• /
• pp.340-344
• /
• 2019

Due to the rapid development of electricity, electronics, information communication, and biotechnology in recent years, studies are actively being conducted on nanopowders as it is required not only for high strengthening but also for high-function powder with electric, magnetic, and optical properties. Nonetheless, studies on nickel nanopowders are rare. In this study of the synthesis of nickel nanoparticles from $LiNiO_2$ (LNO), which is a cathode active material, we have synthesized the nanosized nickel powder by the liquid reduction process of $NiSO_4$ obtained through the leaching and purification of LNO. Moreover, we have studied the reduction reaction rate according to the temperature change of liquid phase reduction and the change of particle size as a function of NaOH addition amount using hydrazine monohydrate ($N_2H_4{\cdot}H_2O$) and NaOH.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.6
• /
• pp.434-441
• /
• 2009

The effect of varying sulfate concentration on continuous fermentative hydrogen production was studied using enriched mixed microflora in continuously fed reactor. Glucose was used as a model substrate for carbohydrates, and hydraulic retention time (HRT) was maintained at 1, 0.5, 0.25 day, respectively. Sulfate concentration was 0${\sim}$20,000 mg/L and the operating pH was maintained at 5.5. The experimental results indicate that hydrogen production is not affected by high sulfate concentration and shorter HRT of 0.25 day enhance hydrogen production. At HRT 1, 0.5, 0.25 day, the hydrogen production rate and hydrogen yield were 2.6, 4.6, 9.4 L/day, and 2.0, 1.8, 1.6 mol $H_2$/mol glucose, respectively. Residual sulfate content was 96${\sim}$98, 95${\sim}$97, and 94${\sim}$97% at HRT 1, 0.5, 0.25 day which show that no sulfate reduction occurred in the reactor during the experiments. Results of Fluorescence In Situ Hybridization (FISH) may indicate the presence of HPB (hydrogen producing bacteria) under all experimental conditions. However, SRB (sulfate reducing bacteria) were not found.

• Journal of Microbiology and Biotechnology
• /
• v.6 no.4
• /
• pp.232-237
• /
• 1996

Growth yield of Desulfovibrio desulfuricans M6 was measured using different substrates. The cell yield of fermentative growth on pyruvate was 6.22 g cell $mol^{-l}$ pyruvate. Since 1 ATP is available from substrate-level phosphorylation from the oxidation of pyruvate to acetate, $Y_{ATP}$ of the bacterium should be the same as $Y_{pyruvate}$ (6.22 g cell $mol^{-l}$ ATP). The cell yields of the bacterium on different electron donors were measured with sulfate as the electron acceptor. Cell yields on lactate, pyruvate and $H_2$ were 9.39, 13.76 and 8.45 g cell $mol^{-l}$ substrate, respectively. From these figures ATP available from electron-transport phosphorylation (ETP) of the electron donors used was calculated. ATP produced by ETP of each electron donnor were 1.71 from pyruvate, 1.51 from lactate and 1.76 from $H_2$. These values show that electrons from the oxidation of lactate to pyruvate are consumed to reduce sulfate through a reverse electron transport mechanism requiring 0.2 ATP for each pair of electrons. Based on these results, discussions are made on the electron transport mechanism in the bacterium.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.3
• /
• pp.59-65
• /
• 2005

There are accumulations of remained chemical additives and contaminants in the process water of semi-closed linerboard mill. High temperature of the process water aggravates the anaerobic digestion of contaminated process water and causes the generation of hazardous gases, which are from the biological reaction of varied additives and contaminants. The hydrogen sulfide in the gases easily combine with moisture in the air, and become sulfuric acid, which causes corrosion of paper machinery. This hydrogen sulfide is from the reduction of sulfate ions in the process water, and the sulfate ions are mostly from the alum. We changed the alum to PAC (Poly Aluminum Chloride). The results were preventing generation of hydrogen sulfide, and equivalent sizing effect by the use of PAC.