• Journal of Mechanical Science and Technology
• /
• 제18권6호
• /
• pp.1019-1025
• /
• 2004

Pressure variation is one of the major sources on noise emission in the axial type oil piston pumps. Therefore, it is necessary that the pressure variation characteristics of the oil hydraulic piston pumps be clarified to reduce the pump noise. Pressure variations in a cylinder at the discharge region and the pump noise were simultaneously measured with discharge pressures and rotational speeds during the pump working. To investigate the effects of the pre-compression and the V-notch in the valve plate, we used the three types of valve plates. In this research, it is clear that the pressure variation characteristics of axial type oil piston pumps is deeply related to the pre-compression and to the V-notch design in valve plate. Therefore, we could reduce the pump noise by using the appropriate pre-compression angle and the notch design that are between the suction port and the discharge port in valve plate.

• Journal of Yeungnam Medical Science
• /
• 제21권1호
• /
• pp.108-113
• /
• 2004

A 23 years old single nulligravida woman underwent laparoscopic removal of a huge cystic adnexal mass that occupied her entire abdomen, giving the appearance of a full term pregnancy. After anesthesia, a vertical infra-umbilical incision, 1 cm long, was made and a telescope was introduced through the port to determine the status of the intra-abdomen and the surface contour of the mass. A needle tipped with a laparoscopic suction apparatus was inserted into the cyst through the infra-umbilical port, directly under the mass. Subsequently, 3,200 ml of cystic fluid was aspirated without spillage. A huge cyst, reaching to the level of the xyphoid process was effectively excised through the operative laparoscopy after prelaparoscopic drainage. Operation time was 140 minutes and hospital stay was 2 days. There were no complications during hospital stay and after discharge. It seems the size of the cyst is not a criteria for the contraindication of laparoscopic surgery.

• 설비공학논문집
• /
• 제19권1호
• /
• pp.19-27
• /
• 2007

Analytical investigation on the performance of a two stage twin rotary compressor for $CO_2$ heat pump water heater system has been carried out. A computer simulation program was made based on analytical models for gas compression in control volumes, leakages among neighboring volumes, and dynamics of moving elements of the compressor. Calculated cooling capacity, compressor input, and COP were well compared to those of experiments over the compressor speeds tested. For the operating condition of suction pressure of 3 MPa, and discharge pressure of 9 MPa, and compressor inlet temperature of $35^{\circ}C$, the compressor efficiency was calculated to be 80.2%: volumetric, adiabatic, and mechanical efficiencies were 88.3%, 93.2%, and 92.7%, respectively. For the present compressor model, volumetric and adiabatic efficiencies of the second stage cylinder were lower by about $6{\sim}7%$ than those of the first stage mainly due to the smaller discharge port at the second stage. Parametric study on the discharge port size showed that the compressor performance could be improved by 3.5% just by increasing the discharge port diameter by 20%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.91-91
• /
• 2011

This paper describes development procedure of the four types of fuel cell's blowers: pressurized fuel blower, selective oxidation air blower, cathode air blower, and burner air blower. Diaphragm blowers having two heads are selected to maintain force balance when the rotating arms are moving by the driving motor. Dimensions of a diaphragm cavity is designed according to the optimal design procedure using numerical simulation and experimental measurement. Experimental apparatus is designed by considering the bower characteristics having low flow rate and high pressure. Test blower is operated by a diaphragm, which has suction and discharge port on the top of the blower. For analyzing the internal flow of the blower, three-dimensional Navier-Stokes analysis is introduced in the present study. Throughout the optimal design of the blowers, blower performance is enhanced by reducing the unbalance motion of the rotating arm and loss region in the diaphragm cavity.

• 한국항해학회지
• /
• 제14권3호
• /
• pp.15-33
• /
• 1990

In recent years, propellers with various blade configurations such as highly skewed propellers are often fitted to ships from the viewpoint of reduction of vibration and noise. In the design of such propellers, design charts based on methodical series tests are to be complemented by theoretical calculations for accurate estimation of propeller open-water characteristics. The author intended to develop a method to estimate propeller open-water characteristics based on Quasi -Vortex - Lattice Method originally developed by Lan for solving planar thin wings, The Quasi - Vortex - Lattice Method has the simplicity and flexibility of Vortex - Lattice Method. Its accuracy is comparable to that of the Vortex - Lattice Method. Converged solution can be obtained with a small number of control points and further, leading edge suction force can be calculated directly. In the present paper, a numerical method to estimate propeller open-water characteristics based on the Quasi - Vortex - Lattice Method is reviewed and its application to marine propellers is described in detail. Comparison of propeller open-water characteristics obtained by the present method with experimental data showed good agreement for a wide variety of propellers including highly skewed propellers.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.329-334
• /
• 2003

Design of pre-compression region(trapping region) of the valve plate is an important element to minimize the pressure fluctuation in a cylinder and in discharge process, and pump noise. In this study, we tried to prove what the characteristics of the oil hydraulic pump would be according to the angle of the trapping region. Three kinds of asymmetrical valve plates were used. As a result, we found that by designing the trapping region, the slope of the pressure rise in the cylinder port from low-pressure suction region to high-pressure discharge region is relaxed and the pressure fluctuation width and the discharge pressure pulsation are reduced. Therefore, because the pump gets smooth pressure fluctuation and low fluid Impact, the pump noise is reduce.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.585-592
• /
• 2009

The performance of screw compressor depends on lots of design parameters of rotor profile, such as length of seal line, wrap angle, blow hole, suction and discharge port size, number of rotor lobe, etc. The optimum rotor profile makes it possible to increase the compression efficiency with low energy consumption, and to minimize the loss of power. In this research, a new rotor profile design and performance analysis are done by computer simulation. It is expected that the volumetric efficiency is improved because the internal leakage is reduced due to the minimization of blow hole and clearance, and the stiffness of rotors is increased due to the reduction of length to diameter ratio. Also, the specific power consumption will be secured for use ranging from low to high operation speed.

• 사물인터넷융복합논문지
• /
• 제3권1호
• /
• pp.25-31
• /
• 2017

미래형 신도시와 최신 아파트들이 건설되며 일반 가정 실내에도 IoT기술이 대거 접목되어 구축된다. 그중 사람들을 쾌적하게 해주는 공기순환기도 내장되어 건설되는데, 공기순환기의 공기를 흡입하는 흡입구와 배출하는 배출구는 실내 곳곳에 설치되어진다. 하지만 이는 중앙 스위치로 on / off 밖에 없기에 조절이 불가능하다. 또한 막심한 전기소모로 인한 다량의 전기세가 나오도록 하며 많은 전기소모는 결국 자원낭비로 이루어진다. 이를 보완하고자 실내 내장형 공기청정기에 미세먼지 감지 장치를 통하여 조절되며 구동되도록 만들어 전기를 절약하는 솔루션을 제안한다. 더불어 배출구는 실내 곳곳에 존재하기에 사람의 위치를 파악하여 홈 네트워크와 연결하여 편의성을 높여주거나 기체분석을 통하여 사용자의 건강을 체크하고 적절히 조절하는 헬스체크 솔루션을 함께 제안한다.

• 한국환경과학회지
• /
• 제19권12호
• /
• pp.1447-1454
• /
• 2010

In this study, the detection limits of lower fatty acids in air were investigated by using Dynamic SPME(Solid Phase Micro-Extraction), i.e. improved Head Space - SPME method(HS-SPME). This Dynamic SPME, called SPDE(Solid Phase Dynamic Extraction), is the analytical method for volatile compounds in air with the extraction by using a stainless steel needle of which inner surface is coated with adsorption material and following the gas chromatographic analysis by inserting the needle into a injection port of GC and subsequently, desorption of the volatile compounds into a gas-chromatographic column. Extraction was carried out by passing the sample air through the needle with a suction pump which has been used for a detection tube. The result of measurement for the 6 lower fatty acids showed that the detection limits ranged from 0.10 ppm to 0.44 ppm and the linear correlation coefficients were over 0.99. Relative standard deviations obtained from 5 analytical repetition of a ca. 1.6 ppm standard mixture were in the range of 1.87%~2.47%. This method has been shown to be a adequate for the measuring C2~C5 fatty acids in air in the concentrations of over several hundreds ppb.

• Journal of Biosystems Engineering
• /
• 제29권5호
• /
• pp.433-440
• /
• 2004

Worldwide consumption of vegetable soybean has been increasing recently, but in the process of vegetable soybean production, threshing and separation work accounts fur about $80\%$ of overall labor. Therefore, developing of the vegetable soybean thresher is necessary to reduce the cost of labor. The main objective of this study is to acquire the basic in-formations for design of the vegetable soybean thresher which is suitable for domestic circumstances. We made the experimental system to investigate the threshing and separating performance at the several speeds of threshing cylinder and separating blower according to the kinds of threshing tooth. The result are as follows; Threshing performance of vegetable soybean thresher was shown as the best in case the threshing tooth made of rubber which has the 80 of Shore hardness was used at the circumference speed of cylinder of 5.8$\~$8.1m/s. Also separating cleaning performance of vegetable soybean thresher was shown as the best at more than 1,300 rpm of blower speed and $60\~80\%$ of opening ratio of suction port.