• 대한기계학회논문집B
• /
• 제23권1호
• /
• pp.92-103
• /
• 1999

The fuel spray behavior in the intake port of an electronic control port irijection gasoline engine has a strong influence on engine performance, exhaust emission and fuel consumption. Thus, in this study, fuel spray behavior and flow characteristics of the air assist gasoline spray injected into a suction flow in a simulated rectangular intake port have boon investigated. Macro-behavior of spray characteristics was investigated by means of visualization and the measurements of SMD and velocity were made by PDPA. For analysis the flow field with droplets size, droplets are classified five droplets size groups. As a result, the normal distance of suction flow increasing, the relatively large droplets distribution and SMD increase because small droplets easily follow suction flow. Near impinging wail, after impinging against the wall, secondary atomized small droplets of D < $30{\mu}m$ bound from the wall. And the increasement of suction flow progress to the large droplets of D > $100{\mu}m$ distribution. Therefore, SMD are apparently increased near impinging wall, Z/d = 9.0.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.63-74
• /
• 1999

When a fuel was injected with opening the intake valve of a port fuel injection engine, the spray atomization and flow characteristics in the intake port have a strong influence on the mixture formation of a combustion chamber. Thus , this study was to clarify the spray flow characteristics of the air-assist gasoline spray with fine dropkets across the suction air stream in model intake port. For the simulated opening intake valve in port, suction air stream was varied to 10m/s ∼30m/s. And fuel pressur ewas fixed to 300kPa, but air assist pressure was varied to 0∼25kPa for a vairable spray conditions. Spray flow trajectory was investigated by means of laser sheet visualization and the measurements of droplet sizes and velocities were made by PDPA system. Measured droplets within the spray flow field were subdivided into five size groups and then, the flow characteristics of droplet size groups were investigated to the spray across a suction air stream.

• Journal of Mechanical Science and Technology
• /
• 제14권12호
• /
• pp.1376-1385
• /
• 2000

This study investigates spray characteristics before and after wall impingingment of gasoline spray in suction air flow. For this study, a rectangular model intake port was made of acrylic glass, and suction air was generated by using the forced air blower contrariwise. The injector for this study was a pintle-type port gasoline injector in which an air-assist adaptor is installed to supply assisted air. A PDPA system was employed to simultaneously measure the size and velocity of droplets near the wall. Measured droplets are divided into "pre-impinging droplets"with positive normal velocity and "post-impinging droplets"were negative normal velocity for the suction flow. The velocities, size distributions and Sauter mean diameter(SMD) of pre-and post-impinging droplets for varions injection angles and air-assists are comparatively analyzed.

• 대한기계학회논문집B
• /
• 제28권4호
• /
• pp.406-414
• /
• 2004

In Gerotor pump, the pressure pulsations which occur due to the pump geometry result in vibration and noise of pump elements as well as cavitation in hydraulic system when the chambers of gerotor enter the delivery port and leave the suction port. Therefore it is important to study on the pressure pulsations before design and analysis of characteristics in Gerotor pump. In this paper, to reduce the unnecessary pressure pulsations, the port plate of Gerotor pump is designed based on the notch of the vane pumps and the relief grove of the piston pumps. The theoretical analysis of the pressure pulsations is performed in consideration of design parameters of the port plate which include each port positions and groove width and operating conditions which include rotational velocity and delivery pressure.

• 한국항해항만학회지
• /
• 제46권2호
• /
• pp.82-91
• /
• 2022

When a ship moves in the proximity of the lateral bank, bank suction forces are generated due to bank effects. Thus, hydrodynamic forces can significantly impact the ship's maneuverability and navigation safety. In this study, model tests were performed to investigate the hydrodynamic forces exerted on a ship, especially suction forces caused by bank effects, using captive model and bank effect tests. A low-speed condition was selected in this study, because of the perilous situation as the ship moves close to the bank. The accuracy of the hydrodynamic forces exerted on the hull was verified, by comparing the results of the static drift test with the results obtained from other institutes at design speed. The straight simulation caused by bank effects was then implemented using estimated hydrodynamic coefficients.

• 한국항공우주학회지
• /
• 제47권1호
• /
• pp.17-25
• /
• 2019

항공기의 Intake는 공간적 제약 또는 생존성 확보의 이유로 S형태의 곡률을 갖는 덕트를 가진다. 그러나 덕트의 곡률은 2차유동과 유동박리의 발생을 야기하며 불균일한 압력분포 생성의 원인이 된다. 본 연구에서는 RAE M 2129 S-Duct의 형상에 보조 Duct를 적용하여 경계층 흡입을 수행하였다. 경계층 흡입의 위치와 각도를 설계변수로 설정하였으며, 흡입면에서 동일 유량을 흡입하는 조건을 부여하였다. S-Duct의 전산해석 타당성을 검증하기 위하여 Port Side와 Starboard Side의 무차원 압력 분포를 ARA 실험값, 전산해석 값과 각각 비교하여 확인하였다. 본 연구에서는 유동 왜곡을 판단하는 공기역학적 성능인자로 유동 왜곡 계수를 사용 하였으며, 경계층 흡입에 의한 유동박리, 와류, 유량 분포 및 압력 분포를 비교 분석 하였다. 그 결과 경계층 흡입 적용 이전과 비교하여 최대 26.14%의 유동 왜곡 계수 저감 효과를 확인하였다.

• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1285-1293
• /
• 2000

In port fuel injection system of SI engines, injected fuel is impinged onto the surface of intake valves and port-wall, and then formed the wall flow under the cold start operation. Wall flows entrained into the cylinder result in the unsteady and nonuniform mixture formation. Therefore, the spray impingement to the wall is considered as having negative influences such as lowering combustion efficiency and causing unburned hydrocarbon emissions. This study investigates the spray characteristics of the wall impinging air-assist spray in suction air flow. A PDPA was used to analyze the flow characteristics under the different conditions such as impingement angle and supplied air. Experimental data concerning the impinging sprays has been obtained in the vicinity of the wall. Measured droplets divided into the pre-impinging droplets which denote as the positive normal velocities and post-impinging droplets that describe as the negative normal velocities for the suction flow. Their velocities, size distributions and SMD are comparatively analyzed before and after the impingement.

• 설비공학논문집
• /
• 제23권8호
• /
• pp.549-555
• /
• 2011

For a $CO_2$ one-stage twin rotary compressor, a T-shaped suction port was used to effectively supply the suction gas stream into two individual suction chambers of the twin cylinders. Suction gas pulsations were observed in the pressure sensor signals and these were simulated by using the acoustic modeling of Helmholz resonators in parallel. The module of acoustic modeling was combined to a computer simulation program for the compressor performance. Validation of the simulation program has been carried out for a bench model compressor in a compressor calorimeter. Cooling capacity and the compressor input power were reasonably well compared between the simulation and the calorimeter test. Particularly, good agreement on P-V diagram between the simulation and the test was obtained.

• 전기학회논문지P
• /
• 제65권4호
• /
• pp.262-267
• /
• 2016

This paper describes a design of a hair drier to improve its performance. the performance of the hair drier can be improved by increasing the wind velocity of its discharge port. the design of the hair drier is accomplished by using the CFD. the validity of design results were verified by comparison with the dry change of the hair drier. In this paper, the initial condition of the applied hair drier is as follows, the number of the blade is 9, the diameter of the suction port is 40[mm], the tip clearance is 12.5[mm], the con angle is $28.5^{\circ}$ and the fan angle is 27.5R. From design results, the enhanced condition of the hair drier can be obtained as follows, the number of the blade is 3, the diameter of the suction port is 50[mm], the tip clearance is 10.5[mm], the con angle is $21.5^{\circ}$ and the fan angle is 75R. At the enhanced condition of the hair drier, the wind velocity of the hair drier is 29[%] increase, and the dry time is 40[%] increase compare to the initial condition of the hair drier.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.12-16
• /
• 2002

Soil, ground water and sea bed are exposed to continuous accumulation of polluted materials causing serious environmental damage. It has been reported that such pollution causes a massive mortality of fish stock in rivers by the resuspension of toxic chemicals during strong wind conditions. Therefore, it becomes apparent that there is an immediate demand for the restoration treatment of polluted river bed (or sea bed) sediment layers. Pollution levels of major rivers and ports such as Pal-dang, Kyung-an rivers, Ma-san port are becoming public concern and are posing a serious environmental threat. In particular, the pollution of Shi-hwa river has become a nation wide issue for last few years. In spite of such public concern, the pollution level of such rivers or port are getting worse everyday. In this study, an environmentally sound engineering package is introduced which helps to restore the polluted river bed or sea bed sediments. This engineering package is consisted of a suction facility followed by a series of mechanical, chemical as well as biological treatment units. The suction facility is designed to minimize the secondary pollution due to the resuspension of toxic materials during suction. The sea bed cleaning engineering package is designed to be installed on the top of a floating barge. Such combination of environmental plant and shipbuilding technology provides a cost-effective solution, minimizing the cost involved in the transportation between suction and treatment facilities.