• Journal of Microbiology and Biotechnology
• /
• v.24 no.12
• /
• pp.1622-1628
• /
• 2014

DagA, a ${\beta}$-agarase, was produced by cultivating a recombinant Streptomyces lividans in a glucose medium or a mixed-sugar medium simulating microalgae hydrolysate. The optimum composition of the glucose medium was identified as 25 g/l glucose, 10 g/l yeast extract, and $5g/l\;MgCl_2{\cdot}6H_2O$. With this, a DagA activity of 7.26 U/ml could be obtained. When a mixed-sugar medium containing 25 g/l of sugars was used, a DagA activity of 4.81 U/ml was obtained with very low substrate utilization efficiency owing to the catabolic repression of glucose against the other sugars. When glucose and galactose were removed from the medium, an unexpectedly high DagA activity of about 8.7 U/ml was obtained, even though a smaller amount of sugars was used. It is recommended for better substrate utilization and process economics that glucose and galactose be eliminated from the medium, by being consumed by some other useful applications, before the production of DagA.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.2
• /
• pp.206-212
• /
• 2011

The effect of process parameters on $H_2$ production from water vapor excited by HF ICP has been qualitatively examined for the first time. With the increase of ICP power, characteristics of $H_2$ production from $H_2O$ dissociation in plasma was divided into 3 regions according to both reaction mechanism and energy efficiency. At the edge of region (II) in the range of middle ICP power, energy effective hydrogen production from $H_2O$ plasma can be achieved. Furthermore, within the region (II) power condition, heating of substrate up to $500^{\circ}C$ shows additional increase of 70~80% in $H_2$ production compared to $H_2O$ plasma without substrate heating. This study have shown that combination of optimal plasma power (region II) and wall heating (around $500^{\circ}C$) is one of effective ways for $H_2$ production from $H_2O$.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.4
• /
• pp.93-100
• /
• 1998

Pyoelectric infrared detectors based on La-modified PbTiO3 (PLT) thin films have been fabricated by RF magnetron sputtering and micromachining technology. The detectors form Pb$_{1-x}$ La$_{x}$Ti$_{1-x}$ O$_{3}$ (x=0.05) thin film ferroelectric capacitors epitaxially grown by RF magnetron sputtering on Pt/MgO (100) substrate. The sputtered PLT thin film exhibits highly c-axis oriented crystal struture that no poling trealization for sensing applications is required. This is an essential factor to increase the yield for realization of an infrared image sensor. Micromachining technology is used to lower the thermal mass of the detector by giving maximum sensor efficiency. Polyimide is coated on top of the sensing elements to support the fragile structure and the backside of the MgO substrate is selectively eteched to reduce the heat loss. The sensing element exhibited a very high detectivity D* of 8.5*10$^{8}$ cm..root.Hz/W at room temperature and it is about 100 times higher than the case of micromachining technology is not used. a sensing system that detects the position as well as the existence of a human body is realized using the array sensor.sor.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.89-99
• /
• 1995

In this paper, we ecamined the effect that MCM-L technique influencess on the design and fabrication of multichip memory modules in increasing the packing desity of memory capacity and maximizing its electrical characteristics. For that purpose, we examined the effective methods of reducing the area of module layout and the wiring length with the variation of chip allocation and the number of wiring layers. We fabricated a 256K${\times}$8bit SRAM module with eight 32K${\times}$8bit SRAM chips. The routing experiment showed that we could optimize the area of module layout and wiring length by placing chips in a row, arranging module I/O pads parallel to chip I/O pads, and equalizing the number of terminal sides of module I/O's to that of chip I/O's. The routing was optimized when we used three wire layers in case of one sided chip mounting or five wire layers in case of double sided chip mounting. The fabricated modules showed 18.9 cm/cm$^{2}$ in wiring density, 65 % in substrate occupancy efficiency, and module substrate and functionally tested to find out the module working perfectly.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.7
• /
• pp.36-42
• /
• 2000

Some polarization characteristics of reflection type photopolymer are investigated. Photopolymer on a Mylar substrate alters an incoming linearly polarized laser beam to an elliptical polarization. Due to the rotation of the polarization, the recording gratings show different diffraction efficiencies. The rotation angle is of order of 10-50% for the tested samples. It is found that the polymer layer does not changes the polarization direction but the Mylar substrate alone distorts the incoming polarization to a comparable degree. As align the polarization states of photopolymers to be parallel with a laser using a He-Ne laser(633nm), which is not sensitive to that material, it was possible to make high diffraction efficiency gratings.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.469.2-469.2
• /
• 2014

All-solid-state solar cell based on Chloride doped organometallic halide perovskite, (CH3NH3)PbIxCl3-x, has achieved a highly power conversion efficiency (PCE) to over 15% [1] and further improvements are expected up to 20% [2]. In this way, solar cells using novel light absorbing perovskite material are actively being studied as a next generation solar cells. However, making solution-process require high temperature up to $500^{\circ}C$ to form compact hole blocking layer and sinter the mesoporous oxide scaffold layer. Because of this high temperature process, fabrication of flexible solar cells on plastic substrate is still troubleshooting. In this study, we fabricated highly efficient flexible perovskite solar cells with PCE in excess of 11%. Atomic layer deposition (ALD) is used to deposit dense $TiO_2$ as hole blocking layer on ITO/PEN substrate. The all fabrication process is done at low temperature below $150^{\circ}C$. This work shows that one of the important blueprint for commercial use of perovskite solar cells.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.2
• /
• pp.109-117
• /
• 1994

Effect of ultrasonic agitation on the contact properties was studied in Ni electroless plating and Pd activation. P-type Si bare wafers were used as substrate and DMAB was used as reducing agent due to its good electrical properties, solderability and compatibility to substrate. In activation, high density Pd nuclei of small size were formed during ultra-sonic agitation compared to that of no stirring. In electroless plating, the plating rate was enhanced by 30∼90% by using ultrasonic agitation. In elecrtoless plating, inhibitor is the most effective additives in ultrasonic agitation. In this experi-ment, thiourea was used as inhibitor. The less the amount of the inhibitor, the more ultrasonic agitation efficiency. It is confirmed by SEM that Ni-B films formed by ultrasonic were coarser, less porous, and denser than those of no stirring. In ultrasonic agitation, boron content of the films was more than those of no stirring. In this case, the more DMAB concentration, the higher the temperature, the less pH, the more boron content. Resistivity of the films formed by ultrasonic agitation was higher than that of no strirring. As the content of boron was increased, the resistivity of the films was increased exponentially.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.24-24
• /
• 1991

Cr-N films were deposited on low-carbon steel sheets by the reactive arc-induced ion plating (AIIP). The influence of the deposition conditions (nitrogen pressure and substrate bias voltage) on the crystal orientation, morphology and microhardness of the Cr-N films has been investigated using x-ray diffractometer and scanning electron microscope. The impurities and contaminations on the surface and at the interface, and the layer-by-layer compositions of the film have been analyzed using scanning Auger multiprobe (SAM) and glow discharge spectroscope (GDS). The mixed state of Cr and Cr2N turned out to have a fine fibrous structure. The Cr2N films were deposited at a wide range of nitrogen flow rates. The orientations of Cr2N films were mainly (110) and (111), and the intensity of the (111) peak increased as the substrate bias voltage increased. The micorstructure of the Cr2N film was dense and no columnar structure was observed. The films in the mixed state of Cr2N and CrN were also dense without columnar structure. The maximum microhardness of the Cr-N films was 2400 kg/$\textrm{mm}^2$ at 10gf load.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.99-106
• /
• 2010

Gas turbines operation for power generation increased rapidly since 1990 due to the high efficiency in combined cycle, relatively low construction cost and low emission. But the operation and maintenance cost for gas turbine is high because the expensive superalloy hot gas path parts should be repaired and replaced periodically This study analyzed the initiation and propagation of the crack at the gas turbine blades which are coated with MCrAIY as a bond coat and TBC as a top coat. The sample blades had been serviced at the actual gas turbines for power generation. Total 7 sets of blades were analyzed and they have different EOH(equivalent operation hour). Blades were sectioned and the cracking distribution were measured and analyzed utilizing SEM(scanning electron microscope) and optical microscope. The blades which had 52,000 EOH of operation had cracks at the substrate and the maximum depth was 0.2 mm. Most of the cracks initiated at the boundary layer between TBC and bond coat and propagated down to the bond coat. Once bond coat is cracked, the base metal is exposed to the oxidation condition and undergoes notch effect. Under this environment, the crack branched at the inter-diffusion layer and propagated to the substrate. Critical cracks affecting the blade life were analyzed as those on suction side and platform.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.1
• /
• pp.24-33
• /
• 1992

Cr-N films were deposited on low-carbon steel sheets by the reactive arc-induced ion plating (AIIP). The influence of the deposition conditions (nitrogen pressure and substrate bias voltage) on the crystal orientation, morphology and microhardness of the Cr-N films has been investigated using x-ray diffractometer and scanning electron microscope. The impurities and contaminations on the surface and at the interface, and the layer-by-layer compositions of the film have been analyzed using scanning Auger multiprobe (SAM) and glow discharge spectroscope (GDS). The mixed state of Cr and Cr₂N turned out to have a fine fibrous structure. The Cr₂N films were deposited at a wide range of nitrogen flow rates. The orientations of Cr₂N films were mainly (110) and (111), and the intensity of the (111) peak increased as the substrate bias voltage increased. The microstructure of the Cr₂N film was dense and no columnar structure was observed. The films in the mixed state of Cr₂N and CrN were also dense without columnar structure. The maximum microhardness of the Cr-N films was 2400 kg/㎟ at 10 gf load.