• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.361-365
• /
• 2002

Advancements in silicon phase control (SCR) technologies provide an arc welding power supply that has the capability to allow the alteration of the Alternating Current (AC) welding output. These technologies provide a square wave output involving sixteen frequency selections and multiple balance selections. While an AC out put is known to minimize magnetic disturbances associate with Direct Current (DC), the potentials of a non-sinusoidal waveform have not been explored. The focus of the paper is to determine the effects that the frequency and balance of an AC wave form output will have upon a high speed Submerge Arc (SAW) application. The test matrix of the project includes welding .250" steel plate. Joint type is square groove with a travel speed of 65 IPM. Each of the weld parameters was held constant, only the frequency and/or balance were altered between welds. Each frequency/balance combination involved three-gap spacing. Upon completion of the welds the bead profiles were measured and recorded. A relationships/trends were observed with various frequency and balance values. Optimum frequency and balance values were found for the .250" square groove application which permit consistent weld sizing, ease of slag removal, and minimal plate distortion.

• Journal of Welding and Joining
• /
• v.32 no.4
• /
• pp.1-9
• /
• 2014

A quantitative understanding on the effect of the welding conditions on weld joint dimensions and weld thermal cycle is difficult through experimental studies alone. The experimental realization of temperature distribution in the weld pool is proved to be extremely difficult due to the small size of welds, high peak temperature and steep temperature gradients in weld pool. This review deals with the heat transfer and fluid flow analysis to understand the parametric influence of a single wire submerged arc welding (SAW) and multi-wire SAW processes on the weld bead dimensions, temperature and fluid flow distribution in the weldment.

• Journal of Korean Society for Quality Management
• /
• v.21 no.2
• /
• pp.242-253
• /
• 1993

The interpretation of the reaction mechanism is significant to produce the high quality welds and understand the welding processes. This investigation is important for the design of welding consumables and the selection of welding process parameters to develop the high quality welds. The objective of this study is to investigate the effect of electrochemical reactions on the transfer of alloy elements between slag and weld metal during submerged arc welding During submerged arc welding weld metal composition is shown to be controlled by two reaction mechanisms in four reaction zones. The responsible reaction mechanisms are thermochemical and electrochemical reactions. The possible reaction sites are the melted electrode tip, the detached droplet, the hot weld pool immediately below the moving electrode, and the cooling and solidifying weld pool behind the moving electrode. The possible reactions in submerged arc welding at different zones of the process is schematically shown in Figure 1.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.1-10
• /
• 2014

The efficient application of any welding process depends on the understanding of associated process parameters influence on the weld quality. The weld quality includes the weld bead dimensions, temperature distribution, metallurgical phases and the mechanical properties. A detailed review on the experimental and numerical approaches to understand the parametric influence of a single wire submerged arc welding (SAW) and multi-wire SAW processes on the final weld quality is reported in two parts. The first part deals with the experimental approaches which explain the parametric influence on the weld bead dimensions, metallurgical phases and the mechanical properties of the SAW weldment. Furthermore, the studies related to statistical modeling of the present welding process are also discussed. The second part deals with the numerical approaches which focus on the conduction based, and heat transfer and fluid flow analysis based studies in the present welding process. The present paper is the first part.

• Journal of Welding and Joining
• /
• v.11 no.4
• /
• pp.79-90
• /
• 1993

Shielded metal arc welding, one-ploe and two-pole submerged arc welding were accomplished to investigate microstructure changes on phase transformation behavior in $60kg/mm^2$ quenched and tempered high strength steel. Microstructures were examined by optical micrograph and TEM. In shielded metal arc welding (oxygen 250ppm), the inclusions were small size (0.3-0.5$\mu\textrm{m}$)and small in number. In submerged arc welding (oxygen 430-529ppm), the inclusions were larger(0.7-2$\mu\textrm{m}$) than that of shielded metal arc welding and large in number. Microstructure mainly depends on number and distribution of inclusions in fusion zone of weld metal. It was noticed that a limited number of inclusions favors the formation of acicular ferrite.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.336-341
• /
• 2002

Recent developments in sensor hardware and in advanced software have made it feasible to consider automating some of the most difficult welding operations. This paper describes some techniques used to automate successfully multipass submerged arc welding operations typically used in pressure vessel manufacture, shipbuilding, production of offshore structures and in pipe mills.

• Journal of Welding and Joining
• /
• v.22 no.5
• /
• pp.26-31
• /
• 2004

In order to propose the optimum welding condition for field application, the effects of welding heat input and cooling rate at PWHT on the mechanical properties were investigated. Submerged arc welding of 1.25Cr-0.5Mo steel for pressure vessel was conducted at welding heat inputs of 15.2kJ/cm, 30.9kJ/cm, and 44.8kJ/cm, and cooling rates of 184$^{\circ}C$/hr, 55$^{\circ}C$/hr, and 2$0^{\circ}C$/hr at PWHT. From the test results, as the welding heat input increase up to 30.9kJ/cm, the changes of microstructure and impact toughness were small. At the heat input of 44.8kJ/cm, however, toughness decreased obviously due to the coarsening of coarse-grained HAZ and formation of ferrite at bainite grainboundary of weld metal. On the other hand, cooling rates at PWHT did not effect on the changes in microstructure and mechanical properties. Even though tensile strength and impact toughness at all welding conditions of this study were above the minimum specification requirement, it was confirmed that heat input of 30.9kJ/cm was the optimum welding condition to improve welding performance by higher heat input.

• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.363-365
• /
• 2001

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.589-595
• /
• 2013

This paper was to study the effect to Yongrak phenomenon of I groove submerged arc welding depending on the plasma cutting surface characteristics, and how to reduce the causes and characteristics Yongrak phenomenon. Shipbuilding and marine structures is designed to use the thick plates and welded by high current to obtain deep penetration. Yongrak phenomenon has been occurred frequently depending on the quality of cutting surface and it makes degrade of the welding quality and modification of the welding. As a result, it was confirmed that I Groove plasma cutting characteristics get bevel form of 2 to 4 degrees to one side direction from the vertical position with Yongrak phenomenon. This is the main reason of Yongrak phenomenon in butt joint welding and 4 degree reverse bevel on the upper surface of base metal by submerged arc welding brought the effect of significant reduction of Yongrak phenomenon.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.139-149
• /
• 1995

Many pressure vessels for the power plants are fabricated from low alloy ferritic steels. The inner sides of the pressure vessels are commonly weld_cladded with austenitic stainless steels to minimize problems of corrosive attack. The submerged-arc welding(SAW) process is now used in preference to other processes because of the possibilities open to automation to reduce the overaII welding times. The most reliable way to avoid underclad cracks(UCC) which are often detected at the overlap of the clad beads is to use nonsusceptible steels such as SA508 class 3. At present domestically developed forging steel of SA508 cl.S is now being cladded with single layer by using 90mm wide strip, which transfers higher heat input into the base metal compared to the conventional two layers strip cladding which has been in wide use with 30-60 mm wide strip. But the current indices for the influence of heat input on crack susceptibility are not accurate enough to express the subtle difference in crack susceptibility of the steel. Therefore, the purpose of this present study is: l) To determine UCC susceptibility on domestic forging steel, SA508 cl.S cladded with single layer by using submerged arc 90mm strip and, 2) To optimize heat input range by which the crack susceptibility could be eliminated.