In this study, Mitigation of Potential-induced degradation (PID) for PERC solar cells using SiO2 Structure of ARC layer. The conventional PID test was conducted with a cell-level test based on the IEC-62804 test standard, but a copper PID test device was manufactured to increase the PID detection rate. The accelerated aging test was conducted by maintaining 96 hours with a potential difference of 1000 V at a temperature of 60℃. As a result, the PERC solar cell of SiO2-Free ARC structure decreased 22.11% compared to the initial efficiency, and the PERC solar cell of the Upper-SiO2 ARC structure decreased 30.78% of the initial efficiency and the PID reliability was not good. However, the PERC solar cell with the lower-SiO2 ARC structure reduced only 2.44%, effectively mitigating the degradation of PID. Na+ ions in the cover glass generate PID on the surface of the PERC solar cell. In order to prevent PID, the structure of SiNx and SiO2 thin films of the ARC layer is important. SiO2 thin film must be deposited on bottom of ARC layer and the surface of the PERC solar cell N-type emitter to prevent surface recombination and stacking fault defects of the PERC solar cell and mitigated PID degradation.
MMC(Modular Multilevel Converter)형 STATCOM 개발을 위해서는 시스템을 이루는 핵심 구성 요소인 Valve의 설계 및 신뢰성 검증이 매우 중요하다. Valve란 다수의 Sub-module을 직렬로 연결, 조합한 것이며 시스템의 용량에 따라 모듈의 직렬 개수가 정해진다. 그러므로 Valve의 최적 설계 및 제어가 시스템의 성능을 개선할 수 있는 주요 항목으로 작용한다. 본 논문에서는 이러한 Valve를 제작한 내용과 시험 설비를 통해 수행된 제품의 운전 특성에 대해서 기술하였다.
무연솔더에 Fe 입자를 첨가하여 Cu3Sn 금속간화합물 성장을 억제하고 취성파괴를 방지하는 연구는 보고된 바 있으나 이러한 복합솔더를 TLP(transient liquid phase) 본딩에 적용한 경우는 아직 없다. 본 연구에서는 Sn계 무연솔더 내부에 Fe 입자의 함량을 적절히 조절하여 Sn-3.5Ag-15.0Fe 복합솔더를 제작하고 TLP 본딩에 적용하여 접합부 전체를 Sn-Fe 금속간화합물로 변화시킴으로써 고온 솔더로서의 적용 가능성을 탐색하였다. 접합공정 중에 형성되는 FeSn2 금속간화합물은 513℃의 고융점을 가지므로 사용 중 온도가 280℃까지 상승하는 전력반도체용 파워모듈에 안정적으로 적용이 가능하다. 칩과 기판에 ENIG(electroless nickel-immersion gold) 표면처리를 적용한 결과 접합부에 Ni3Sn4/FeSn2/Ni3Sn4의 다층 금속간화합물 구조를 형성하였으며 전단시험시 파괴경로는 Ni3Sn4/FeSn2 계면에서 균열이 진전하다가 FeSn2 내부로 전파되는 양상을 보였다. TLP 접합공정 2시간 이후에는 30 MPa 이상의 전단강도를 얻었고 특히 200℃ 전단시험에서도 강도 저하가 전혀 없었다. 본 연구결과는 최근 활발히 연구되고 있는 전기자동차용 파워모듈에 적용할 수 있는 소재 및 공정으로 기대할 수 있다.
Purpose. The purpose of this study was to investigate effects of preclinical OSCE(Objective Structured Clinical Evaluation) on knowledge, confidence in their Core fundamental nursing skills and self-efficacy in nursing students. Method. The research design was a one group pretest-posttest design and it was done to assess changes in knowledge, confidence in core fundamental nursing skills and self-efficacy from pre to the post-test which was given after the OSCE. Data were collected from March 5 to April 7, 2016 from 37 nursing students who were taking the 15-hours using OSCE learning module at one Gyeongbuk-do, P-city. This practicum was composed of 4 core fundamental nursing skills and 5 other fundamental nursing skills. The knowledge consisted of a 10-item by researchers and the confidence of core fundamental nursing skills consisted of an 9-item NRS and the self-efficacy consisted of a 17-item 5-point scale and measured in both the pretest and posttest. The collected data were analyzed with SPSS IBM 20.0 program for the frequency, percentage, x2-test, and paired t-test. Rusult. The results showed that although scores of knowledge of OSCE learning module were significanlty increased from 5.22 to 7.03(t=5.30, p<.001). There were significantly increased in scores of confidence in core fundamental nursing skills from 5.13 to 7.27(t=10.01, p<.001), In the sub-scales of each core fundamental nursing skills was scored the highest. otherwise, there was no significant difference in self-efficacy(t=1.42, p=.161). Conclusions. Based on the results, this study suggests that OSCE module development activities for nursing students in nursing education-learning in order to improve nursing skills.
본 논문에서는 Bare-die Chip 형태의 Drive amplifier를 Ajinomoto Build-up Film (ABF)와 FR-4로 구성된 PCB에 내장함으로써 28 GHz 대역 모듈에서 적용될 수 있는 내장형 능동소자 모듈을 구현하였다. 내장형 모듈에 사용된 유전체 ABF는 유전율 3.2, 유전손실 0.016의 특성을 가지고 있으며, Cavity가 형성되어 Drive amplifier가 내장되는 FR4는 유전율 3.5, 유전손실 0.02의 특성을 가진다. 제안된 내장형 Drive amplifier는 총 2가지 구조로 공정하였으며 측정을 통해 각각의 S-Parameter특성을 확인하였다. 공정을 진행한 2가지 구조는 Bare-die Chip의 패드가 위를 향하는 Face-up 내장 구조와 Bare-die Chip의 패드가 아래를 향하는 Face-down내장 구조이다. 구현한 내장형 모듈은 Taconic 사의 TLY-5A(유전율 2.17, 유전손실 0.0002)를 이용한 테스트 보드에 실장 하여 측정을 진행하였다. Face-down 구조로 내장한 모듈은 Face-up 구조에 비해 Bare-die chip의 RF signal패드에서부터 형성된 패턴까지의 배선 길이가 짧아 이득 성능이 좋을 것이라 예상하였지만, Bare-die chip에 위치한 Ground가 Through via를 통해 접지되는 만큼 Drive amplifier에 Ground가 확보되지 않아 발진이 발생한다는 것을 확인하였다. 반면 Bare-die chip의 G round가 부착되는 PCB의 패턴에 직접적으로 접지되는 Face-up 구조는 25 GHz에서부터 30 GHz까지 약 10 dB 이상의 안정적인 이득 특성을 냈으며 목표주파수 대역인 28 GHz에서의 이득은 12.32 dB이다. Face-up 구조로 내장한 모듈의 출력 특성은 신호 발생기와 신호분석기를 사용하여 측정하였다. 신호 발생기의 입력전력(Pin)을 -10 dBm에서 20 dBm까지 인가하여 측정하였을 때, 구현한 내장형 모듈의 이득압축점(P1dB)는 20.38 dB으로 특성을 확인할 수 있었다. 측정을 통해 본 논문에서 사용한 Drive amplifier와 같은 Bare-die chip을 PCB에 내장할 때 Ground 접지 방식에 따라 발진이 개선된다는 것을 검증하였으며, 이를 통해 Chip Face-up 구조로 Drive amplifier를 내장한 모듈은 밀리미터파 대역의 통신 모듈에 충분히 적용될 수 있을 것이라고 판단된다.
대한원격탐사학회 2002년도 Proceedings of International Symposium on Remote Sensing
/
pp.229-234
/
2002
Under the hostile influence of the extreme space environmental conditions due to the deep space and direct solar flux, the thermal control in space applications is especially of major importance. There are tight temperature range restrictions for electro-optical elements while on the other hand there are low power consumption requirements due to the limited energy sources on the spacecraft. So, we usually have strong requirement of thermal and power control module in space applications. In this paper, the design concept of a thermal and power control module in the MSC(Multi-Spectral Camera) system which will be a payload on KOMPSATII is described in terms of H/W & S/W. This thermal and power control module, called THTM(Thermal and Telemetry Module) in MSC, resides inside the PMU(Payload Management Unit) which is responsible for the proper management of the MSC payload for controlling and monitoring the temperature insides the EOS(Electro-Optic System) and gathering all the analog telemetry from all the MSC sub-units, etc. Particularly, the designed heater controller has the special mode of "duty cycle" in addition to normal closed loop control mode as usual. THTM controls heaters in open loop according to on/off set time designed through analysis in duty cycle mode in case of all thermistor failure whereas it controls heaters by comparing the thermistor value to temperature based on closed loop in normal mode. And a designed THTM provides a checking and protection method against the failure in thermal control command using the test pulse in command itself.
본 연구에서는 중공사형 지지체막을 폴리술폰(polysulfone, PSf) 고분자를 이용하여 비용매 상분리법(non solvent induced phase separation, NIPS)에 의해 제조하였다. 제조된 중공사 지지체막을 PDMS와 Pebax를 코팅하여 중공사형 복합막을 제조하고 CO2, H2, O2 그리고 N2에 대한 순수 투과도(permeance)와 선택도를 측정하였다. 제조된 복합막 모듈 중에서 선택도(CO2/H2)가 가장 높은 모듈을 선정하여 모사가스를 사용하여 스테이지컷(stage cut, SC)의 변화에 따라 분리성능을 측정하였다. 이때 사용된 모사가스는 PSA에서 버려지는 off gas의 농도인 CO2 70% : H2 30%인 것을 사용하였다. 1단 실험에서는 H2 농도 약 60%, H2 회수율 12%의 값을 얻을 수 있었다. 낮은 H2 농도와 회수율을 극복하기 위해 2단 직렬 테스트를 수행하였으며, 이를 통해 H2 농도 약 70%, H2 회수율 70%를 달성할 수 있었으며, 이를 통해 CO2/H2 분리에 대하여 분리 공정 구성을 도출할 수 있었다.
This study proposes a new test circuit and control method for the submodules of modular multilevel converter (MMC)-based HVDC systems. The test current of conventional submodule test circuits cannot provide the DC offset components or may have some distortion in the linearized current with the DC offset. The proposed scheme can provide not only the DC component but also linearized current without distortion. Therefore, the submodule test current waveform is relatively similar to that of a real submodule consisting of an MMC-based HVDC system. The validity of the proposed circuit and control method is verified through a simulation and experiment.
This paper presents the thermohydrodynamic analysis of tilting journal pad bearings supporting a power turbine rotor applied to a 250 kW super-critical $CO_2$ cycle. In the analysis, the generalized Reynolds equation and 3D energy equation are solved to predict oil film temperature and the 3D heat conduction equation is solved for pad temperature. The power turbine rotor is supported by two tilting pad bearings consisting of five pads with an oil supply block between the pads. Copper backing pads with higher thermal conductivity compared to steel backing pads are adopted to improve thermal management. The predicted maximum pad temperature is around $55^{\circ}C$ which is approximately $15^{\circ}C$ higher than oil supply temperature. In addition, the predicted minimum film thickness is 50 mm at a rotating speed of 5,000 rpm. These results indicate that there is no issue in the thermal behavior of the bearing. An operation test is performed with a power turbine module consisting of a power turbine, a reduction gear and a generator. Thermocouples are installed at the 75% position from the leading edge of the pad to monitor pad temperature. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation. The steady state pad temperatures measured in the test show good agreement with the predicted temperatures.
e-4WD(Electric-4WD) system is a 4WD(4-Wheel Drive) System that can transform a car into a Hybrid System. e-4WD consists of a Motor, Inverter, Speed reducer and Clutch. The Motor, Speed reducer and Clutch are installed on the rear sub-frame as a chassis module type. The inverter is installed separately. Compared to a mechanical 4WD, the e-4WD system has many advantages. For example, the reduced number of drivetrain components makes better use of the space. Driving with a motor only at low speed improves fuel economy and reduces exhaust gas. Engine downsizing is available because the motor assists the engine. The performance of a conventional HEV(Hybrid Electric Vehicle) system can also be maintained. This paper proposes the specifications of components and the control logic for an e-4WD System. And the effect of the e-4WD system is proven using a test vehicle equipped with components under various test conditions.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.