• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.345-350
• /
• 2008

The magnitude of constraint effect $A_2$ value was experimentally estimated by using crack tip opening displacement(CTOD) between elastic and plastic regions near crack tip front for CT specimen with $25.4t{\ss}{\AE}$ SS400 steel. The constraint effect, $A_2$ was dependent on specimen configuration and on the measured positions of CTOD near crack front. $A_2$ should be estimated using the opening displacement calculated within crack front plastic region. If not, it's not reliable to evaluate of constraint effect at crack growth initiation in this paper.

• Korean Chemical Engineering Research
• /
• v.43 no.6
• /
• pp.740-744
• /
• 2005

Perovskite-type oxide $La_{1-x}Sr_xCo_{1-y}Fe_yO_{3-{\delta}}$ sols were prepared by sol-gel method using $La(NO_3)_3{\cdot}xH_2O$, $Sr(NO_3)_2$, $Co(NO_3)_2{\cdot}6H_2O$ and $Fe(NO_3)_3{\cdot}9H_2O$ as starting materials. The properties of the perovskite-type oxide sols were investigated by viscometer, FT-IR, TG-DTA and XRD. The prepared sols showed 1.16 cp in average viscosity, and a strong acidic condition of pH 0.5, irrespective of composition of the starting materials. The viscosity of sols at the same volume decreases, but the gelation time of sols, at which the sol viscosity increases rapidly, increases when increasing La concentration in composition of starting materials.

• Journal of Food Hygiene and Safety
• /
• v.36 no.3
• /
• pp.220-227
• /
• 2021

Fluoroimide is a fungicide and is also used as a pesticide for persimmons and potatoes. The established fluoroimide pesticide analysis method takes a long time to perform and uses benzene, a carcinogen. In addition, a lower limit of quantification is required due to enforcement of the Positive List System. Therefore, this study aimed to improve the analysis method for residual fluoroimide to resolve the problems associated with the current method. The analytical method was improved with reference to the increased stability of fluoroimide under acidic conditions. Fluoroimide was extracted under acidic conditions by hydrogen chloride (4 N) and acetic acid. MgSO₄ and NaCl were used with acetonitrile. C₁₈ (octadecylsilane) 500 mg and graphitized carbon black 40 mg were used in the purification process. The experiment was conducted with agricultural products (hulled rice, potato, soybean, mandarin, green pepper), and liquid chromatograph-tandem mass spectrometry was used for the instrumental analysis. Recovery of fluoroimide was 85.7-106.9% with relative standard deviations (RSDs) of less than 15.6%. This study reports an improved method for the analysis of fluoroimide that might contribute to safety by substituting the use of benzene, a harmful solvent. Furthermore, the use of QuEChERS increased the efficiency of the improved method. Finally, this research confirmed the precise limit of quantification and these results could be used to improve the analysis of other residual pesticides in agricultural products.

• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.406-412
• /
• 2020

SrMoO₄:RE³⁺ (RE=Dy, Sm, Tb, Eu, Dy/Sm) phosphors are prepared by co-precipitation method. The effects of the type and the molar ratio of activator ions on the structural, morphological, and optical properties of the phosphor particles are investigated. X-ray diffraction data reveal that all the phosphors have a tetragonal system with a main (112) diffraction peak. The emission spectra of the SrMoO₄ phosphors doped with several activator ions indicate different multicolor emissions: strong yellow-emitting light at 573 nm for Dy³⁺, red light at 643 nm for Sm³⁺, green light at 545 nm for Tb³⁺, and reddish orange light at 614 nm for Eu³⁺ activator ions. The Dy³⁺ singly-doped SrMoO₄ phosphor shows two dominant emission peaks at 479 and 573 nm corresponding to the ⁴F_9/2→⁶H_15/2 magnetic dipole transition and ⁴F_9/2→⁶H_13/2 electric dipole transition, respectively. For Dy³⁺ and Sm³⁺ doubly-doped SrMoO₄ phosphors, two kinds of emission peaks are observed. The two emission peaks at 479 and 573 nm are attributed to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions of Dy³⁺ and two emission bands centered at 599 and 643 nm are ascribed to ⁴G_5/2→⁶H_7/2 and ⁴G_5/2→⁶H_9/2 transitions of Sm³⁺. As the concentration of Sm³⁺ increases from 1 to 5 mol%, the intensities of the emission bands of Dy³⁺ gradually decrease; those of Sm³⁺ slowly increase and reach maxima at 5 mol% of Sm³⁺ ions, and then rapidly decrease with increasing molar ratio of Sm³⁺ ions due to the concentration quenching effect. Fluorescent security inks based on as-prepared phosphors are synthesized and designed to demonstrate an anti-counterfeiting application.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.175-183
• /
• 2008

Adsorption equilibria of the gases $CO_2$, CO, $CH_4$ and $H_2$ and their binary mixtures on Li-X zeolite (UOP) were obtained by static volumetric method in the pressure range of 0 to 20 bar at temperatures of 293.15, 303.15, and 313.15 K. Using the parameter obtained from single-component adsorption isotherm. Multicomponent adsorption equilibra could be predicted and compared with experimental data. Extended Langmuir isotherm, Extended Langmuir-Freundlich isotherm (L-F) and dual-site Langmuir isotherm (DSL) were used to predict the experimental results for binary adsorption equilibria of $H_2/CO_2$, $H_2/CO$, and $H_2/CH_4$ on Li-X Zeolite. Extended Langmuir-Freundlich isotherm predicted equilibria of $CH_4$ and $H_2$ better than any other isotherm. One the other hand DSL isotherm predicted equilibria of $CO_2$ and CO very well.

• Korean Journal of Materials Research
• /
• v.18 no.9
• /
• pp.457-462
• /
• 2008

Through the electrostatic interaction between the poly-diallydimethylammonium chloride (PDDA) modified Multi-walled carbon nanotube (MWNT) and $SnO_2$ suspension in 1mM $NaNo_3$ solution, MWNT-$SnO_2$ nanocomposites (MSC) for anode electrodes of a Li-ion battery were successfully fabricated by colloidal heterocoagulation method. TEM observation showed that most of the $SnO_2$ nanoparticles were uniformly deposited on the outside surface of the MWNT. Galvanostatic charge/discharge cycling tests showed that MSC anodes exhibited higher specific capacities than bare MWNT and better cyclability than unsupported nano-$SnO_2$ anodes. Also, after 20 cycles, the MSC anode fabricated by heterocoagulation method showed more stable cycle properties than the simply mixed MSC anode. These improved electrochemical properties are attributed to the MWNT, which adsorbs the mechanical stress induced from volume change and increasing electrical conductivity of the MSC anode, and suppresses the aggregation between the $SnO_2$ nanoparticles.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.590-597
• /
• 2010

HTGR using a TRISO coated particles as nuclear raw fuel material can be used to produce clean hydrogen gas and process heat for a next-generation energy source. For these purposes, a TRISO coated particle was prepared with 3 pyro-carbon (buffer, IPyC, and OPyC) layers and 1 silicone carbide (SiC) layer using a CVD technique on a spherical $UO_2$ kernel surface as a fissile material. In this study, a spherical $UO_2$ particle was prepared using a modified sol-gel method with a vibrating nozzle system, and TRISO coating fabrication was carried out using a fluidized bed reactor with coating gases, such as acetylene, propylene, and methyltrichlorosilane (MTS). As the results of this study, a spherical $UO_2$ kernel with a sphericity of 1+0.06 was obtained, and the main process parameters in the $UO_2$ kernel preparation were the well-formed nature of the spherical ADU liquid droplets and the suitable temperature control in the thermal treatment of intermediate compounds in the ADU, $UO_3$, and $UO_2$ conversions. Also, the important parameters for the TRISO coating procedure were the coating temperature and feed rate of the feeding gas in the PyC layer coating, the coating temperature, and the volume fraction of the reactant and inert gases in the SiC deposition.

• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.419-424
• /
• 2009

Congruent or stoichiometric $LiNbO_3$ fiber single crystals were grown by the $\mu$-PD method, and the grown fiber crystals have the several (2 or 3) ridges with a diameter of $1.35{\sim}1.5\;mm$ and a length of $40{\sim}100\;mm$. In this $\mu$-PD process, different growth rates ($10{\sim}60\;mm/h$) were applied. Pt wire or $LiNbO_3$ crystal was used as a seed. The properties of grown $LiNbO_3$ fiber single crystals having a-axis or c-axis according to seeds were effected by the grown conditions(Pt tube diameter, pulling speed, after heater etc.). Disk-type $LiNbO_3$ samples were poled in condition of DC 5 V/cm at 1050, 1075 or $1100^{\circ}C$. XRD, SEM, conoscope image through the polarized microscope, $T_C$ measuring apparatus, optical transmittance measuring instrument are used to identify the properties of $LiNbO_3$.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.6
• /
• pp.420-425
• /
• 1999

Time of flight diffraction(TOFD) method is used in nondestructive tests of piping and pressure vessels because of its advantages over a pulse echo technique: its speed, objectivity, repeatability and its insensitivity to specimen surface conditions and discontinuity orientation. But it is the one of weak points in TOFD method that it has the dead zone in sub-surface resolution induced by lateral waves. We solved the dead-zone problem near the sub-surface by using the deconvolution method and the developed ultrasonic testing system showed high performance.

• Journal of Sensor Science and Technology
• /
• v.18 no.6
• /
• pp.417-422
• /
• 2009

The problems associated with the synthesis, characterization and application of $SnO_2$-Au nanocomposites for the optimization of conductometric gas sensors have been discussed in this report. Nanocomposites have been synthesized on the surface of $SnO_2$ films using successive ionic layer deposition(SILD) method. It has been shown that the proposed approach to surface modification of metal oxide films is an excellent method for the optimization of the operating characteristics of $SnO_2$-based gas sensors, being developed for the detection of reducing gases as well as ozone.