• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.45-48
• /
• 2008

Under earthquake loads, the columns on the lower stories carry large axial forces and horizontal forces as the earthquake loads are acting horizontally and vertically on the building. To distribute the energy entered into the building under earthquakes according to the plastic deformation of the members, it is safer and more economic to persuade plastic hinge to occur in the beams rather than on the columns. However, it is unavoidable to have plastic hinge occurring on the columns when it is applied on both of the main axes of the building, which results in high shear force on the column end, and reinforced concrete column may result in sudden brittle failure due to bending moment and shear force. To increase restriction of the reinforced concrete column on the horizontal forces, this study uses repetitive loading experiments with different amount of shear reinforcement, and analyzes and compares the structural safety and behaviour of the reinforced test materials.

• Culinary science and hospitality research
• /
• v.17 no.4
• /
• pp.153-168
• /
• 2011

This study investigated the relationship between consumers' knowledge and risk perception towards purchase intention of organic food. The data were collected from a sample of 311 housewives in Seoul and Ulsan. A structural equation modelling technique was used to test the causal model. The results indicated that subjective knowledge was significantly associated with purchasing organic food. Objective knowledge, in contrast, was only indirectly associated with purchasing organic food, through increased subjective knowledge and risk perception towards purchasing organic food. Risk perception towards organic food had a direct positive and relatively strong relationship with purchasing organic food. Implications of the results and limitations of the study were discussed.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.3
• /
• pp.123-128
• /
• 2020

Analysis of the 2016 Gyeongju earthquake and the 2017 Pohang earthquake showed the characteristics of a typical high-frequency earthquake with many high-frequency components, short time strong motion duration, and large peak ground acceleration relative to the magnitude of the earthquake. Domestic nuclear power plants were designed and evaluated based on NRC's Regulatory Guide 1.60 design response spectrum, which had a great deal of energy in the low-frequency range. Therefore, nuclear power plants should carry out seismic verification and seismic performance evaluation of systems, structures, and components by reflecting the domestic characteristics of earthquakes. In this study, high-frequency amplification factors that can be used for seismic verification and seismic performance evaluation of nuclear power plant systems, structures, and equipment were analyzed. In order to analyze the high-frequency amplification factor, five sets of seismic time history were generated, which were matched with the uniform hazard response spectrum to reflect the characteristics of domestic earthquake motion. The nuclear power plant was subjected to seismic analysis for the construction of the Korean standard nuclear power plant, OPR1000, which is a reactor building, an auxiliary building assembly, a component cooling water heat exchanger building, and an essential service water building. Based on the results of the seismic analysis, a high-frequency amplification factor was derived upon the calculation of the floor response spectrum of the important locations of nuclear power plants. The high-frequency amplification factor can be effectively used for the seismic verification and seismic performance evaluation of electric equipment which are sensitive to high-frequency earthquakes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.797-803
• /
• 2010

A vehicle door impact beam made of a thin sheet of steel has been constructed using hot stamping technology with the aim of ensuring occupant safety in the event of a side collision. This technology has been used to increase the strength of the vehicle body parts and to reduce the weight of the door impact beam as well as the number of work processes. Mechanical tests were performed to determine the material properties of the hot-stamped specimen and the results of the tests were used as input data in stamping and structural simulation in order to obtain the optimal design of door impact beam. The strength of the hot-stamped door impact beam increased to a value that was 102% higher than that of conventional pipe-shaped door impact beam. A weight reduction of 34% was also achieved.

• Geophysics and Geophysical Exploration
• /
• v.5 no.3
• /
• pp.185-192
• /
• 2002

We made a study of 3-D migration which could precisely image data of GPR (Ground Penetrating Radar) applied to NDT (Non-Destructive Test) field for the inspection of structural safety. In this study, we obtained 3-D migrated images of important targets in structuresurvey (e.g. steel pipes, cracks) by using 3-D Kirchhoff prestack depth migration scheme developed for seismic data processing. For a concrete model consisting of steel pipe and void, the targets have been well defined with opposite amplitude according to the parameters of the targets. And migrated images using Parallel-Broadside array (XX configuration) have shown higher resolution than those using Perpendicular-Broadside array (YY configuration) when steel pipes had different sizes. Therefore, it is required to analyze the migrated image of XX configuration as well as that of general YY configuration in order to get more accurate information. As the last stage, we chose a model including two steel pipes which cross each other. The upper pipe has been resolved clearly but the lower has been imaged bigger than the model size due to the high conductivity of the upper steel.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.413-418
• /
• 2001

Fundamental failure mode in a laminated composite pinned-joint is proposed to assess damage resulting from stress concentration in the plate. The joint area is a region with stress concentrations thus a complicated stress state exists. The modeling of damage in a laminated composite pinned-joint presents many difficulties because of the complexity of the failure process. In order to model progressive from initial to final, finite element methods are used rather than closed form stress analyses. Failure analysis must be a logical combination of suitable failure criteria and appropriate material properties degradation rules. In this study, the material properties which were obtained in previous study, the preparing process of the bearing strength test for a pinned joint CFRP composite plate subjected to in-plane loading at low temperature, and the FEM result of progressive damage model using ANSYS program are summarized to assess the structural safety of CFRP plate used in the magnetic supporting post of KSTAR(Korea Superconducting Tokamak Advanced Research).

• Fire Science and Engineering
• /
• v.24 no.4
• /
• pp.41-46
• /
• 2010

High strength concrete (HSC) has been mainly used in large SOC structures. HSC have superior property as well as improvement in durability compared with normal strength concrete. In spite of durability of HSC, explosive spalling in concrete front surface near the source of fire occurs serious problem in structural safety. Therefore, this study is concerned with experimentally investigation of fire resistance at high temperature due to fireproof material covering thickness in addition to concrete cover. From the test result, it was appeared that the use of fireproof material results in good performance for fire resistance and spalling prevention, and the optimal fireproof covering thickness is 1~3mm. On the other hand, the temperature was rapidly increased by explosive spalling within 30 minutes and showed very little rise caused by evaporation heat after then. It was also found that the void channel was remained at high temperature as PP fiber melts at about $200^{\circ}C$, and the pore pressure in concrete was decreased.

• Journal of Navigation and Port Research
• /
• v.36 no.5
• /
• pp.357-361
• /
• 2012

Anemometer is a meteorological instrument that measures wind direction and wind speed in real time, and is mounted to the cranes that are used at ports, shipbuilding yards, off-shore structure, or construction sites that are influenced by wind, and it is used in conjunction with the safety system. Load cell-type anemometer measures the wind direction through the ratio of load between 4 positions by mounting the thin plate to 4 load cells, and measures wind velocity through the summation of loads. In this study, we compared and analyzed the results in the theoretic approach, analytic approach and experimental approach to derive the correlation between load ratio and wind direction. Wind direction was selected as the design variable, and selected 9 wind direction conditions from $0^{\circ}{\sim}90^{\circ}$ with $11.25^{\circ}$ space for analysis, and 10 wind direction conditions with $10^{\circ}$ space for experiment.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.18 no.1
• /
• pp.1-41
• /
• 1992

A new and unique class of nonionic surfactants was synthesized by reacting biological a-tocopherol with ethylene oxide for functional cosmetics. The structures were confirmed by Hl-UMR, FT-lR, TLC and elemental analysis. POV and conjugated diene value study for EPO showed POE(n)TE had antioxidative effect similar to tocopheryl acetate Protective effect on cell membrane in photohemolysis of POE(5)TE, POE(10)TE and POE(18)TE were slightly lower than tocopherol but higher than nonoxynol-12, and POE(10)TE had UV absorption power comparable with tocopherol and homosalate. Biological activity of the hydrophobic group of the new surfactants make them unique and different from those of conventional nonionic surfactants Systematic safety evaluations of POE(n)TEs on the skin and eye proved that they are as safe as tocopherol. The results of physicochemical study showed POE(10)TE had the lowest CMC value, POE(18)TE had the maximum surface tension reduction and the highest foam volume and POE(n)TEs had various HLB values by the degree of ethoxylation. The test resul Is of technological and practical applications of these surfactants for cosmetics showed some POE(n)TEs were superior to conventional surfactants. POE(5)TE in W/O emulsions, POE(10)TE and POE(12)TE in O/W emulsions, POE(12)TE in dispersions, POE(18)TE in solubilizations and POE(50)TE in gelations were shown to be excellent which was considered due to the structural characteristic and formation of liquid crystals of POE(n)TEs. By the development and applications of these excel lent multi-functional surfactants, innovative functional cosmetics were successfully formulated.

• Nuclear Engineering and Technology
• /
• v.25 no.3
• /
• pp.353-360
• /
• 1993

Many types of pipe whip restraints are installed to protect the structural components from the anticipated pipe whip phenomena of high energy lines in nuclear power plants. It is necessary to investigate these phenomena accurately in order to design the pipe whip restraints properly and/or to evaluate the acceptability of the pipe whip restraint design. Various research programs have been conducted in many countries to develop analytical methods and to verify the validity of the methods. In this study, various types of finite elements in ANSYS[1], the general purpose finite element computer program, was used to simulate the postulated pipe whips to obtain impact loads and the calculated results were compared with the specific experimental results from the sample pipe whip test for the U-shaped pipe whip restraints. Some calculational models, having the gap element or the spring element between the pipe whip restraint and the pipe line, give reasonably good transient responses of the restraint forces compared with the experimental results, and could be useful in evaluating the acceptability of the pipe whip restraint design.