• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 춘계 학술논문 발표대회
• /
• pp.79-82
• /
• 2008

It has been reported that destruction test by core collection is the most reliable of the structural concrete strength in present building construction field. But it causes low efficiency by damage and cutting in structure due to the core collection. It also has some problems in repairing. Additionally in case of strength test with management specimen, different environment compared to the structure environment cause problems about estimation precise structure strength. Therefore, it is required to develop structure direct strength test that has test values and credibility above the ones obtained by core specimen collection strength test and seasonal specimen test to suggest a reasonable and practical management method of structural concrete.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.119-122
• /
• 2003

This report describes the procedure of detailed design and structural test for the composite flexure which is a part of the hingeless hub system. First, stacking sequence design for composite flexure was done, and structural analysis by using NASTRAN was made to verify structural stability and safety. Using FPS installed at KIMM, composite flexure was laid up and cured using a autoclave. Before rotor ground test, the basic structural tests such as a bench test, tensile strength test and shear strength test, for flexure, were accomplished. Through replacing existing metal hub part with new fabricated composite flexure, improvement of aeroelastic stability and weight reduction were achieved. This result will be applied to composite rotor system design fur helicopter.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.201-207
• /
• 2002

An advanced fiber sheet has been widely used for strengthening of the concrete structures due to its excellent properties such as high strength and light weight. Bond strength is very important in strengthening the concrete structures using an advanced fiber sheet. This research examines the bond behavior between fiber sheet and concrete, investigates the bond strength by the direct pull-out test and the tensile-shear test. To obtain the tensile-shear strength a double-face shear type bond test is conducted. The primary test variables are the types of concrete surface roughness (disk-grinding/chipping) and retrofitting methods (bonding/injection). Thirty specimens were tested to evaluate the bond strength. It is shown that the average bond strength between fiber sheet and concrete by the direct pull-out test and the tensile-shear test is $22.3{\sim}23.1kgf/cm^2$ $17.92{\sim}19.75kgf/cm^2$, respectively.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.775-779
• /
• 2007

The structural strength assessment of a carbody was performed using F.E. analysis and static test to verify the structural safety of newly manufactured carbody of a freight car. The freight car for the transportation of cold-rolled coils in steel making company was designed with SS400 steel for underframe and SM490A steel for bracket. Prior to the evaluation of structural strength, commercial finite element method(FEM) software was used for the stress and structural analyses on stress distribution in a carbody of freight car. The strain gages were attached on the carbody based on the FEM results. The actual vertical loading test and horizontal compression loading test were conducted, and the stress and displacement were obtained. Finally, the structural strength of carbody was evaluated by using a engineering techniques.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권2호
• /
• pp.103-112
• /
• 2008

FRP와 콘크리트의 접착강도를 평가하기 위해 현장에서 일반적으로 사용되는 Pull-off 실험방법은 FRP 복합체의 손상을 초래하며 더욱이 FRP의 최대 pull-off 강도가 콘크리트의 인장강도에 의해 제한되는 단점을 지니고 있다. 이에 따라 구조보강용 접착제의 역학적 특성을 1차적으로 평가할 수 있는 간접적인 실험방법의 개발이 요구된다. 본 연구에서는 여러나라에서 각기 제안되고 있는 실험규격에 대한 비교실험을 통하여 구조보강용 접착제의 역학적 특성을 개략적으로 예측할 수 있는 표준화된 실험방법 및 평가기준을 제안하고자 하였다. 본 연구결과를 바탕으로 인장전단접착강도 시험의 접착제 두께, 압축/휨강도 시험체의 제원 등이 통일되어 표준시험체 제원을 도출할 수 있었다.

• 한국안전학회지
• /
• 제20권3호
• /
• pp.126-133
• /
• 2005

Behavior of saw-dust concrete has not studied because many people have thought that saw-dust concrete cannot be applicable for structural member, up to now. This study is to findout how much the concrete can be structurally applicated. 5mm grid sieve was used to select satisfactory sawdust for better concrete quality. Test molds size of ${\phi}10{\times}20cm$ long were made of normal without sawdust, 0.05%, 0.1%, 0.2%, 0.4%, 0.6%, 0.8%, 1.0%, 1.2%, 1.4%, 1.6%, 1.8% 2.0%, for making concrete strengh of 180kg, 210kg, 240kg, 270kg which they are normally used in practice presently. A various strengths tests such as compressive splitting tensile, flexible strength behavior of structural member named beam using size of $20{\times}30{\times}120cm$ have been done for the structural aspects. Tensile strength shows that it can be more affected than higher strength of it.

• 한국안전학회지
• /
• 제23권4호
• /
• pp.67-71
• /
• 2008

Formwork is a temporary structure that supports its weight and that of fresh concrete as well as construction live loads. Slab formwork consists of sheathing, stringer, hanger and shore. In construction site, pipe supports are usually used as shores which are consisted of the slab formwork. In this study, compressive strength of 80 pipe supports was measured by knife edge test and plate test. Buckling load of pipe supports was analyzed by structural analysis program(MlDAS). Theoretical buckling load with/without initial deformation was got by theoretical analysis. According to these results, buckling load which was analyzed by structural analysis program(MlDAS) was larger than compressive strength of knife edge test and plate test. Theoretical buckling load without initial deformation was larger than compressive strength of knife edge test and plate test. But Theoretical buckling load with initial deformation was lower than compressive strength of knife edge test and plate test. Initial deformation equation for test method according to the pipe support length was suggested. Therefore, the present study results will be used to design the slab formwork safely.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.993-996
• /
• 2008

현재 건설현장에서 구조체 콘크리트 강도는 구조체에서 채취한 코어공시체 강도가 가장 신뢰성이 높다고 알려져 있다. 그러나 코어 채취시 구조체의 손상이나 배근의 절단에 의해서 구조체 성능의 지장을 줄 우려가 있고 공시체 채취후의 보수 등에 몇 가지 문제가 있다. 또한 비파괴 검사에 의한 경우 결과값을 추정하는 방법이기 때문에 신뢰도가 매우 저하되는 단점을 가지고 있다. 본 연구 개발의 목표는 접합 분리 시험체 및 콘크리트의 코어채취에 의한 직접적인 강도 측정방법과 계절별 관리용 공시체 강도를 비교분석하여 보다 발전된 구조체 콘크리트의 성능 평가방법을 제시하여 합리적이고 실용적인 구조체 콘크리트의 시공 품질관리 기법을 제안 하는데 목적이 있다.

• Steel and Composite Structures
• /
• 제3권4호
• /
• pp.243-260
• /
• 2003

This paper reports on the development of a new composite slab system that uses a large- lipped steel channel and reinforced concrete. The advantages of this new system are that it serves as both a structural unit and an unsupported form and it has a secondary structural barrier function. A concrete pouring test was carried out for the large-lipped steel channel. Full-scale tests were carried out to assess the flexural strength-deformation characteristics and structural mechanics of the composite slab. The barrier mechanics of the steel channel concrete element (referred to as the SC subunit) of the composite slab are examined. The test results indicate that the new composite slab has excellent strength, ductility characteristics, and a structural barrier function in its SC subunit that is highly effective against severe loading.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.130-138
• /
• 2004

In this paper, the structural strength of a rolling stock seat were numerically evaluated under several design load conditions based on the UIC requirements. The rot]ins stock seat was designed for the high speed train of a Chinese conventional line. To maximize its weight reduction and structural strength, an aluminium alloy, ALDC8-T5, was applied to the base frame, side frames and armrests. The designed seat frame satisfied the strength requirements on inertia loads and fatigue test conditions. However, it couldn't satisfy the requirements on the static test conditions of UIC 566 OR. Therefore, some design modifications were suggested and numerically evaluated whether the static test requirements could be satisfied or not.