• Composites Research
• /
• 제29권4호
• /
• pp.173-178
• /
• 2016

Graphene oxide (GO) was concurrently reduced and functionalized using long alkyl chain dodecyl amine (DA). The DA functionalized GO (DA-G) was assumed to disperse homogenously in linear low density polyethylene (LLDPE). Subsequently, DA-G was used to fabricate DA-G/LLDPE composites by melt mixing technique. Fourier transform infrared spectra analysis was performed to ascertain the simultaneous reduction and functionlization of GO. Field emission scanning electron microscopy analysis was performed to ensure the homogenous distribution and dispersion of DA-G in LLDPE matrix. The enhanced storage modulus value of the composites validates the homogenous dispersion of DA-G and its good interfacial interaction with LLDPE matrix. An increased in tensile strength value by ~ 64% also confirms the generation of good interface between the two constituents, through which efficient load transfer is possible. However, no significant improvement in glass transition temperature was observed. This simple technique of fabricating LLDPE composites following industrially viable melt mixing procedure could be realizable to developed mechanically strong graphene based LLDPE composites for future applications.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.205.2-205.2
• /
• 2014

The effects of ion beam mixing of a SiC film coated on super alloys (hastelloy X substrates) were studied, aiming at developing highly sustainable materials at above $900^{\circ}C$ in decomposed sulfuric acid gas (SO2/SO3/H2O) channels of a process heat exchanger. The bonding between two dissimilar materials is often problematic, particularly in coating metals with a ceramics protective layer. A strong bonding between SiC and hastelloy X was achieved by mixing the atoms at the interface by an ion-beam: The film was not peeled-off at ${\geq}900^{\circ}C$, confirming excellent adhesion, although the thermal expansion coefficient of hastelloy X is about three times higher than that of SiC. Instead, the SiC film was cracked along the grain boundary of the substrate at above $700^{\circ}C$. At ${\geq}900^{\circ}C$, the film was crystallized forming islands on the substrate so that a considerable part of the substrate surface could be exposed to the corrosive environment. To cover the exposed areas and cracks multiple coating/IBM processes have been developed. An immersion corrosion test in 80% sulfuric acid at $300^{\circ}C$ for 100 h showed that the weight retain rate was gradually increased when increasing the processing time.

• 한국환경과학회지
• /
• 제20권6호
• /
• pp.767-773
• /
• 2011

The objectives of this research are to investigate the proper coagulation conditions which are a type and doses of coagulants, mixing conditions (velocity gradients and mixing times), pH and so on through Jar-test, to evaluate the flux variations, permeate, backwashing according to characteristics of pretreatment of the wastewater by means of MF membranes for river maintenance water reuse. The effluent water from B-city K-sewage treatment plant are used for this research. Turbidity and suspended solids(SS) are 14.2 NTU and 10.4 mg/L respectively. This condition causes fouling for membrane process. The flux decline could be reduced when coagulation pretreatment was carried out. Optimal coagulations PAC which are commonly used in the sewage treatment plant was observed in this research. The results indicate that an optimal coagulation dose and pH are 80 ppm and pH of 7 respectively, but coagulation efficiency was lower at strong acid or strong base. Results showed that continuous and steady operations in membrane separation process by means of the effective removal of organic matter and turbidity with coagulation pretreatment of sewage secondary effluent were achieved.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.47-48
• /
• 2015

Recycled aggregate used in a site is strong alkali due to calcium hydroxide attached on its surface. Accordingly, many environmental problems arise. Therefore, as basic research to reduce pH of recycled aggregate, this study tries to reduce the strong alkalinity of recycled aggregate by using mixture solution based on sodium phosphate and ammonium chloride. As a result, original aggregate has the strong alkalinity of pH 11.23, whereas pH of recycled aggregate immersed in mixture solution decreased as more mixture rate increased, and mostly pH 9.8 or less was found.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1999년도 제13회 학술강연논문집
• /
• pp.27-27
• /
• 1999

To illustrate the global variation of the droplet mean diameters and the turbulent flow characteristics in counterflowing internal mixing pneumatic nozzle, the experimental measurements at five axial downstream locations(i.e., at Z=30, 50, 80, 120, and 170mm) were made using a PDPA(Phase Doppler Particle Analyzer) under the different air injection pressures ranging from 40 ㎪ to 120 ㎪. A nozzle with axi-symmetric tangential-drilled four holes at an angle of 15$^{\circ}$ has been designed and manufactured. The distributions of velocities, turbulence intensities, turbulence kinetic energy, turbulent correlation coefficients, spray angle, droplet mean diameters, volume flux, number density are quantitatively analyzed. It is possible to discern the effects of increasing air pressure. It indicates that the strong axial momentum in spite of more or less disparity between the velocity components means more reluctant to disperse radially, and that axial fluctuating velocities are substantially higher than those of radial and tangential ones, suggesting that the disintegration process is enhanced under higher air assist. The larger droplets are detected in the spray centerline at the near stations and smaller ones are generated due to further subsequent breakup at farther axial locations are attributed to the internal mixing type nozzle characteristics. Despite of the strong axial momentum, the poor atomization around the centre close to the nozzle exit is attributed to the lower rates of spherical particles which are not subject to instantaneous breakup. As it goes downstream, however, substantial increases in SMD(Sauter Mean Diameter) from the central part toward spray periphery are understandable because the droplet relative velocity is too low to bring about any subsequent disintegration.

• Journal of the korean society of oceanography
• /
• 제31권2호
• /
• pp.75-88
• /
• 1996

The analytic and numerical solution of the 1$\frac{1}{2}$-layer and 2$\frac{1}{2}$-layer models are derived. The large coastal-sea level drop and the fast westward speed of the anticyclonic gyre due to strong offshore winds using two ocean models are investigated. The models are forced by wind stress fields similar in structure to the intense mountain-pass jets(${\sim}$20 dyne/$cm^{2}$) that appear in the Gulfs of Tehuantepec and Papagayo in the Central America for periods of 3${\sim}$7 days. Analytic and numerical solutions compare favorably with observations, the large sea-level drop (${\sim}$30 cm) at the coast and the fast westward propagation speeds (${\sim}$13 km/day) of the gyres. The coastal sea-level drop is enhanced by several factors: horizontal mixing, enhanced forcing, coastal geometry, and the existence of a second active layer in the 2$\frac{1}{2}$-layer model. Horizontal mixing enhances the sea-level drop because the coastal boundary layer is actually narrower with mixing. The forcing ${\tau}$/h is enhanced near the coast where h is thin. Especially, in analytic solutions to the 2$\frac{1}{2}$-layer model the presence of two baroclinic modes increases the sea-level drop to some degree. Of theses factors the strengthened forcing ${\tau}$/h has the largest effect on the magnitude of the drop, and when all of them are included the resulting maximum drop is -30.0 cm, close to observed values. To investigate the processes that influence the propagation speeds of anticyclonic gyre, several test wind-forced calculations were carried out. Solutions to dynamically simpler versions of the 1$\frac{1}{2}$-layer model show that the speed is increased both by ${\beta}$-induced self-advection and by larger h at the center ofthe gyres. Solutions to the 2$\frac{1}{2}$-layer model indicate that the lower-layer flow field advects the gyre westward and southward, significantly increasing their propagation speed. The Papagayo gyre propagates westward at a speed of 12.8 km/day, close to observed speeds.

• 한국농공학회지
• /
• 제26권1호
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• 한국해양학회지:바다
• /
• 제16권4호
• /
• pp.155-168
• /
• 2011

여름철 황해 동부 연안 저층에 형성되는 수온전선을 따라 북쪽으로 흐르는 연안 경계류의 크기와 위치에 영향을 주는 요소들을 3차원 수치모형인 ROMS를 이용하여 살펴보았다. 여름에 수심이 깊은 외해에서는 태양 가열로 강한 성층에 존재하지만 수심이 얕은 연안에서는 조류가 일으키는 저층 혼합으로 해수물성이 연직으로 잘 혼합된다. 이 과정에서 성층화된 외해와 연직 혼합이 잘되고 수온이 높은 연안 사이에서 수온전선이 형성되며, 수온전선을 가로 지르는 방향의 밀도 구배에 의해 수온전선을 따라 북쪽으로 흐르는 연안 경계류가 발생함을 확인하였다. 해류계를 이용한 현장 관측에서도 약 10 cm/s로 북상하는 연안 경계류가 관측되었다. 이러한 수온전선을 따라 북쪽으로 흐르는 연안 경계류는 주로 조류와 바람의 영향을 크게 받는다. 조류에 의한 저층 혼합과 바람에 의한 표층 혼합이 여름철 황해 동부 경계류에 가장 큰 영향을 주는 요소다. 바람에 의한 표층 혼합은 북쪽으로 흐르는 황해 동부 연안 경계류의 폭을 더 넓게 하여 수송량을 증가시킨다. 강물의 유입과 일사량의 변화는 연안 경계류의 세기와 위치 변화에 큰 영향을 주지 않는다. 성층이 강하게 이루어지는 여름철 황해 동부 연안 $36^{\circ}N$에서는 대조기(소조기) 동안 강한(약한) 조류가 북쪽으로 흐르는 해류의 수송량을 증가(감소)시키지만, 동안 경계류의 위치를 크게 변화시키지는 않는다. 연안 경계류의 평균적인 위치는 바람의 세기 변화에 따라 변화하였다.

• 한국해양학회지:바다
• /
• 제18권3호
• /
• pp.111-121
• /
• 2013

지역규모의 정확한 일기예보와 해양생태계 변화 이해에 있어서 수온 예측은 매우 중요하다. 황해는 조류가 매우 빠르고 탁도가 높다. 이러한 해역에서는 수치 모델의 수직 혼합 기법 및 해수의 탁도에 따른 수형(water type)이 수온 구조 결정에 많은 영향을 미친다. 수직 혼합 기법 변화와 탁도의 변화에 따른 황해 수온 모사의 민감도를 알아보기 위해 3차원 해양 순환 모델인 Regional Ocean Modeling System (ROMS)을 사용하여 수치 실험을 수행하였다. 수직 혼합 기법은 해양 순환 모델에서 많이 사용되는 Mellor-Yamada level 2.5 closure(M-Y)와 K-Profile parameterization (KPP)을 사용하고, 탁도는 Jerlov의 분류에 따른 수형 1, 3, 5를 사용하여 수치 실험을 수행하고 그 결과를 국립수산과학원에서 제공하는 정선 해양 관측 자료와 비교, 분석하였다. M-Y 기법은 수직적 혼합을 상대적으로 강하게 모의하였으며 그 결과로 저층수온이 높게 형성되었다. 높은 저층 수온은 탁도를 높게 설정하면 완화되지만 표층 수온이 높아지는 단점이 있다. KPP 기법은 M-Y 기법보다는 수직 혼합을 약하게 모의하고 이 약한 수직 혼합 때문에 황해 연안을 따라 형성되는 조석전선을 잘 재현하지 못하였으나, 저층 수온은 관측 수온에 더 가깝게 재현하였다. 결과적으로 황해 3차원 해양순환 모델실험에서 M-Y 기법은 수직 혼합이 잘 되어 표층과 저층의 수온 차이가 작게 나타나고, KPP 기법은 이와 반대로 모의하였다. 탁도의 영향을 표현하는 Jerlov 수형은 높을수록 일사량이 낮은 수심까지만 투과되어 성층을 잘 표현하였고, 낮을수록 깊은 수심까지 일사량이 투과되어 표층과 저층의 수온차를 작게 모의하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2133-2138
• /
• 2003

In general, flow entrainment of surrounding gas into a supersonic jet is caused by the pressure drop inside the jet and the shear actions between the jet and the surrounding gas. In the recent industrial applications, like supersonic ejector system or scramjet engine, the rapid mixing of two different gases is important in that it determines the whole performance of the flow system. However, the mixing performance of the conventional circular jet is very low because the shear actions are not enough. The supersonic jet discharging from a petal nozzle is known to enhance mixing effects with the surrounding gas because it produces strong longitudinal vortices due to the velocity differences from both the major and minor axes of petal nozzle. This study aims to enhance the mixing performance of the jet with surrounding gas by using the lobed petal nozzle. The jet flows from the petal nozzle are compared with those from the conventional circular nozzle. The petal nozzles employed are 4, 6, and 8 lobed shapes with a design Mach number of 1.7 each, and the circular nozzle has the same design Mach number. The pitot impact pressures are measured in detail to specify the jet flows. For flow visualization, the schlieren optical method is used. The experimental results reveal that the petal nozzle reduces the supersonic length of the supersonic jet, and leads to the improved mixing performance compared with the conventional circular jet.