• Earthquakes and Structures
• /
• 제4권5호
• /
• pp.471-487
• /
• 2013

Performance of a prototype base isolated building located at Indian Institute of Technology, Guwahati (IITG) has been studied here. Two numbers of three storeyed single bay RCC framed prototype buildings were constructed for experimental purpose at IITG, one supported on conventional isolated footings and the other on a seismic isolation system, consisting of lead plug bearings. Force balance accelerometers and a 12 channel strong motion recorder have been used for recording building response during seismic events. Floor responses from these buildings show amplification for the conventional building while 60 to 70% reduction has been observed for the isolated building. Numerical models of both the buildings have been created in SAP2000 Nonlinear. Infill walls have been modeled as compression struts and have been incorporated into the 3D models using Gap elements. System identification of the recorded data has been carried out using Parametric State Space Modeling (N4SID) and the numerical models have been updated accordingly. The study demonstrates the effectiveness of base isolation systems in controlling seismic response of isolated buildings thereby leading to increased levels of seismic protection. The numerical models calibrated by relatively low level of earthquake shaking provides the starting point for modeling the non-linear response of the building when subjected to strong shaking.

• KCI Concrete Journal
• /
• 제12권1호
• /
• pp.23-34
• /
• 2000

Experiments were carried out to investigate the seismic behaviors, such as lateral strength, ductility and energy-dissipation capacity. of high-strength concrete (HSC) square short column confined in thin steel shell. The primary objective of the study was to investigate the suitability of using HSC square columns confined in thin steel shell in region of moderate-to-high seismic risk. A total of six columns, consisting of two ordinarily reinforced concrete square short columns and four reinforced concrete square short columns confined in thin steel shell was tested. Column specimens, short columns in a moment resisting frame with girder. were tested under a constant axial and reversed cyclic lateral loads. To design the specimens. transverse reinforcing methods, level of axial load applied, and the steel tube width-thickness ratio (D/t) were chosen as main parameters. Test results were also discussed and compared in the light of improvements in general behaviors, ductility, and energy-absorption capacities. Compared to conventionally reinforced concrete columns, the HSC columns confined in thin steel shell had similar load-displacement hysteretic behavior but exhibited greater energy-dissipation characteristics . It is concluded that, in strong earthquake areas, the transverse reinforcing method by using a thin steel shell (D/t=125) is quite effective to make HSC short columns with very strong and ductile.

• Earthquakes and Structures
• /
• 제10권3호
• /
• pp.645-667
• /
• 2016

The 750 m long "De Bosset" bridge in the Cephalonia Island of Western Greece, being the area with the highest seismicity in Europe, was constructed in 1830 by successive stone arches and stiff block-type piers. The bridge suffered extensive damages during past earthquakes, such as the strong M7.2 earthquake of 1953, followed by poorly-designed reconstruction schemes with reinforced concrete. In 2005, a multidisciplinary project for the seismic assessment and restoration of the "De Bosset" bridge was undertaken under the auspices of the Greek Ministry of Culture. The proposed retrofitting scheme combining soil improvement, structural strengthening and reconstruction of the deteriorated masonry sections was recently applied on site. Design of the rehabilitation measures and assessment of the pre- and post-interventions seismic response of the bridge were based on detailed in-situ and laboratory tests, providing foundation soil and structural material properties. In-situ inspection of the rehabilitated bridge following the strong M6.1 and M6.0 Cephalonia earthquakes of January 26th and February 3rd 2014, respectively, revealed no damages or visible defects. The efficiency of the bridge retrofitting is also proved by a preliminary performance analysis of the bridge under the recorded ground motion induced by the above earthquakes.

• Earthquakes and Structures
• /
• 제16권5호
• /
• pp.575-588
• /
• 2019

Seismic design method based on bearing capacity has been widely adopted in building codes around the world, however, damage and collapse state of structure under strong earthquake can not be reflected accurately. This paper aims to present a deformation-based seismic design method based on the research of RC component deformation index limit, which combines with the feature of Chinese building codes. In the proposed method, building performance is divided into five levels and components are classified into three types according to their importance. Five specific design approaches, namely, "Elastic Design", "Unyielding Design", "Limit Design", "Minimum Section Design" and "Deformation Assessment", are defined and used in different scenarios to prove whether the seismic performance objectives are attained. For the components which exhibit ductile failure, deformation of components under strong earthquake are obtained quantitatively in order to identify the damage state of the components. For the components which present brittle shear failure, their performance is guaranteed by bearing capacity. As a case study, seismic design of an extremely irregular twin-tower high rise building was carried out according to the proposed method. The results evidenced that the damage and anti-collapse ability of structure were estimated and controlled by both deformation and bearing capacity.

• 한국지진공학회논문집
• /
• 제22권3호
• /
• pp.175-184
• /
• 2018

In this paper, comparative analysis of the 9.12 Gyeongju and 11.15 Pohang earthquakes was conducted in order to provide probable explanations and reasons for the damage observed in the 11.15 Pohang earthquake from both earthquake and structural engineering perspectives. The damage potentials like Arias intensity, effective peak ground acceleration, etc observed in the 11.15 Pohang earthquake were generally weaker than those of the 9.12 Gyeongju earthquake. However, in contrast to the high-frequency dominant nature of the 9.12 Gyeongju earthquake records, the spectral power of PHA2 record observed in the soft soil site was highly concentrated around 2Hz. The base shear around 2 Hz frequency was as high as 40% building weight. This frequency band is very close to the fundamental frequency of the piloti-type buildings severely damaged in the northern part of Pohang. Unfortunately, in addition to inherent vertical irregularity, most of the damaged piloti-type buildings had plan irregularity as well and were non-seismic. All these contributed to the fatal damage. Inelastic dynamic analysis indicated that PHA2 record demands system ductility capacity of 3.5 for a structure with a fundamental period of 0.5 sec and yield base shear strength of 10% building weight. The system ductility level of 3.5 seems very difficult to be achievable in non-seismic brittle piloti-type buildings. The soil profile of the PHA2 site was inversely estimated based on deconvolution technique and trial-error procedure with utilizing available records measured at several rock sites during the 11.15 Pohang earthquake. The soil profile estimated was very typical of soil class D, implying significant soil amplification in the 11.15 Pohang earthquake. The 11.15 Pohang earthquake gave us the expensive lesson that near-collapse damage to irregular and brittle buildings is highly possible when soil is soft and epicenter is close, although the earthquake magnitude is just minor to moderate (M 5+).

• 대한토목학회논문집
• /
• 제13권4호
• /
• pp.65-75
• /
• 1993

본 연구는 규모가 큰 지진하중에 대한 해양 가이드 타워의 비정상과정 거동해법에 주안점을 두었으며, 아울러 작은 파랑이나 조류하중이 동시에 작용할 수 있는 경우도 고려하였다. 지진에 의한 지반운동의 비정상특성은 정상과정 성분에 지수함수의 시간포락함수를 곱하는 형태로 모형화하였다. 동적거동의 비정상과정 분산값을 해석적인 방법으로 산출하였다. 운동방정식에 계류장치의 비선형 복원력과 파동에 의한 비선형 점성저항력을 추계론적 최적화기법으로 선형화하여 동적해석을 수행하였다. 지진의 발생기간동안 예상되는 중급의 파랑하중에 의한 영향을 최대거동 산정시 고려하였다. 중급 파고조건에 대한 파랑하중은 지속기간이 상당히 길어서 정상과정으로 취급할 수 있으므로 이에 대해서는 주파수 영역해석을 사용하여 동적거동을 산출하고 이 결과를 지진에 의한 비정상과정거동에 반영하였다. 예제해석으로부터 비정상과정 해석방법을 검증하고, 지진과 파랑 및 조류하중의 각 성분이 전체응답에 미치는 영향을 분석하였다.

• 한국지진공학회논문집
• /
• 제8권6호통권40호
• /
• pp.13-22
• /
• 2004

연성 계수는 반응수정계수(R)의 핵심구성요소로서 내진설계에서 중요한 역할을 하는 계수이다. 본 연구에서의 연성계수()는 단자유도 구조물의 연성계수()에 다자유도 보정계수()를 곱하여 평가하였다. 단자유도 시스템의 연성계수는 지진하중을 받는 단자유도 구조물의 변위 연성요구도와 주기에 따른 비선형 동적해석으로부터 산정하였다. 다자유도 시스템의 영향을 고려하기 위한 다자유도 보정계수()는 기존의 연구에 근거하여 제시하였다. 철골 연성 모멘트 골조의 연성계수를 평가하기 위하여, 구조물의 층수, 골조시스템(외곽골조, 분배골조), 붕괴 메카니즘(강-기둥 약-보, 약-기둥 강-보), 토질조건 및 지진구역을 변수로 하여 총 108개의 예제 구조물을 설계하였다. 구조물의 층수, 붕괴 메카니즘 및 토질조건은 연성계수에 큰 영향을 미치는 반면, 골조 시스템 및 지진구역은 연성계수에 영향을 미치지 않는 것으로 나타났다.

• 한국산학기술학회논문지
• /
• 제17권5호
• /
• pp.36-41
• /
• 2016

본 논문에서는 다중재난하중을 받는 인접건물의 동적응답에 대한 연결제어기법의 제어성능을 수치해석적인 방법을 사용하여 검토하였다. 이를 위하여 강진지역인 LA 지역의 지진하중과 강풍지역인 찰스턴 지역의 풍하중을 사용하여 수치해석을 수행하였다. 인공 지진하중과 풍하중은 ASCE 7-10을 바탕으로 생성하였고 인공지진하중은 SIMQKE을 사용하여 작성하였으며 인공풍하중은 Kaimal Spectrum을 이용하여 작성하였다. 10층 및 20층의 인접구조물을 예제구조물로 사용하였고 비선형 이력댐퍼를 이용하여 연결제어를 하였다. 비선형 이력댐퍼를 간편하게 모형화하기 위하여 주로 MR 감쇠기를 모형화 할 때 사용하는 Bouc-Wen 모델을 사용하였다. 비선형 이력댐퍼는 10층에만 설치한 경우와 1층에서 10층까지 모든 층에 설치한 경우에 대해서 고려하였다. 각 층에 사용하는 댐퍼의 개수를 증가시킨 파라메터 스터디를 수행하였고 지진하중 및 풍하중에 대한 최적의 성능을 보이는 설계안을 검토하였다. 수치해석결과 비선형 이력댐퍼를 이용한 연결제어를 통하여 다중재난 하중에 대한 인접건물의 동적응답을 효과적으로 저감시킬 수 있었고 각각의 재난하중에 대한 최적설계결과가 다르게 나타나는 것을 확인할 수 있었다. 또한 연결되는 감쇠기를 과도하게 사용하면 오히려 구조물의 응답을 증가시킬 수 있으므로 주의 깊은 설계과정이 필요함을 알 수 있었다.

• 한국전산구조공학회논문집
• /
• 제32권5호
• /
• pp.323-331
• /
• 2019

강한 지진의 영향에 있는 레디얼 게이트에 작용하는 동수압 산정을 위한 계산 모형이 제시되었다. 지진동으로 움직이는 구조물의 영향을 호소부와의 이동경계면으로 처리함과 아울러 강한 지진동 효과를 고려하여 동적 레이어링법이 적용된 ALE 알고리즘과 호소부 자유수면 거동을 위한 SIMPLE법을 사용하는 것이 제안된다. 제안된 방법은 단순한 수직 또는 경사 댐체 벽면에 대하여 널리 알려진 실험 결과 및 그로부터 유도된 제안식과 비교하여 타당성과 유효성이 증명되었다. 계산모형에서 사용할 호소부 상류부 측의 무한경계까지의 거리를 산정하기 위한 파라미터 분석을 수행하여 호소부 수위의 2배가 최적의 길이임을 관찰하였다. 마지막으로 제안된 계산 모형을 사용하여 여러 곡률의 대형 레디얼 게이트에 작용하는 지진동수압을 성공적으로 산출하였다.

• Smart Structures and Systems
• /
• 제5권4호
• /
• pp.427-442
• /
• 2009

In this paper, the acceptability of system identification results for health monitoring of instrumented bridges is addressed. This is conducted by comparing the confidence intervals of identified modal parameters for a bridge in California, namely Truckee I80/Truckee river bridge, with the change of these parameters caused by several damage scenarios. A challenge to the accuracy of the identified modal parameters involves consequences regarding the damage detection and health monitoring, as some of the identified modal information is essentially not useable for acquiring a reliable damage diagnosis of the bridge system. Use of strong motion data has limitations that should not be ignored. The results and conclusions underline these limitations while presenting the opportunities offered by system identification using strong motion data for better understanding and monitoring the health of bridge systems.