• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.101-108
• /
• 2004

It is very important to diagnose state of knife and strip cutting face in real time in the side trimming process due to improvement of quality of trimming face. In this study, diagnosis system for knife and strip cutting face was developed. CCD camera was installed at the both side of strip in the entry of burr masher roll. This system offer to operator the diagnosis result that was analyzed image obtained from CCD camera. As a result, bad quality of trimming face is decreased below 1/10 and knife breakage is detected $100\%$.

• 소성∙가공
• /
• 제19권6호
• /
• pp.344-351
• /
• 2010

This paper presents a precision on-line model for the prediction of the roll force and tension distributions across the strip in hot strip rolling. The approach is based on an approximate 3-D theory of rolling, and in particular, considers the effect of pre-deformation of the strip, which occurs near the roll entrance before the strip enters the bite zone. The prediction accuracy of the proposed model is examined through comparison with the predictions from the 3-D finite element models.

• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.327-333
• /
• 2003

Most of shape defects in steel strip are originated from the structure of rolling mill itself. For instance, strip crown occurs when the work roll is deformed by the bending moment induced on roll chocks. To get rids of the shape defects, it is necessary to increase the stiffness of rolling mill. The structure change of back-up roll is one of alternative ways to increase the mill stiffness without facility revamping from 4 high mill to 6 high mill. In this research work, the new back-up roll was developed and can be used in any type of 4 high mill to reduce the strip shape defects. The developed back-up roll consists of sleeve, arbor and phase angle adjusting system for arbor. The circumference of arbor is specially machined to adapt the strip width change during rolling. The experimental cold rolling test was done to prove the effectiveness of newly developed back-up roll. The experimental rolling results show that the new back-up roll has more powerful performance in reducing the shape defects than conventional back-up roll. It was also found that the new back-up roll has higher stability for shape control. In addition to, the only sleeve surface needs to be reground and changed in most cases, so that the maintenance cost can be greatly reduced.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.374-374
• /
• 2000

In this paper, we developed an ANFIS controller through ES algorithm for disturbances rejection in Hot Rolling. The looper of a Hot Rolling is installed between each pair of stands and plays key roles to enhance the product quality of the strip by controlling the tension and the width of the strip. At the same time, the AGC on top of the Mill produces a strip with the desired thickness through pressing its Mill. Between both, however, interactions are caused by coupling effects among strip tension, looper angle and strip thickness. In addition, in case disturbances, it is more difficult to keep strip quantities desirable. So we present an ANFIS controller through ES algorithm which is able to identify fuzzy rule with input/output data and update itself through output errors.

• 소성∙가공
• /
• 제18권5호
• /
• pp.377-384
• /
• 2009

The shape of edge cracking in rolling process generally occurred "V" shape. This cracking is successively generated at width edge of strip. The edge cracking is developed to center of strip during rolling process. In the results, the strip is occurred fracture, and the productivity is gone down because of the extensive production time. Accordingly, we need to control crack propagation during rolling process. But, the control of cracking is very difficult in rolling process. Previously the studies of edge cracking were mainly performed on hot rolling process. In this paper, the shape of the edge cracking in rolling was estimated according to process conditions such as initial edge crack size, reduction ratio and tension using FE-simulation and the simplicity experiments on cold rolling process.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1155-1165
• /
• 1990

본 연구에서는 롤압력과 롤토크를 예측하는 새로운 방법이 제시된다. 이 방 법은 롤 간극에서의 자세한 변형도속도의 분포를 예측할 수 있으며, 특히 롤압력과 롤 토크의 계산에 필요한 유동응력 분포도 계산할 수 있다. 이 방법을 이용하여 압연조 건과 재료성질이 롤압력, 압하력, 롤토그 등에 미치는 영향을 조사하였다. 또한, 이 방법에 의해서 예측된 결과를 참고문헌과 포항제철의 공정 데이터로부터 발췌한 실험 데이터와 비교하였으며, 유한요소 해석결과와도 비교하였다.

• 소성∙가공
• /
• 제28권4호
• /
• pp.190-196
• /
• 2019

The capability of accurately predicting the roll force profile across a strip in the bite zone in cold rolling process is vital for the calculation of strip profile. This paper presents a derivation of a precision mathematical model for predicting variations in the roll force across a strip in cold rolling. While the derivation is based on an approximate 3-D theory of rolling, this mathematical model also considers plastic deformation in the pre-deformation region which is located close to the roll entrance before the strip enters the bite zone. Finally, the mathematical model is expressed as a boundary value problem, and it predicts the roll force profile and tension profile in addition to lateral plastic strain profile.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.125-128
• /
• 2001

A finite element-based, integrated process model is presented for coupled analysis of the thermal and metallurgical behavior of the strip occurring on the run-out-table in hot strip rolling. The validity of the proposed model is examined through comparison with measurements. The models capability of revealing the effect of cooling pattern on strip temperatures and the optimal cooling pattern are demonstrated through a series of process simulation. In order to improve strip shape and control temperature history of thickness direction for strip during ROT cooling.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.412-422
• /
• 1999

Scale defects generated on the strip surface in a tandem finishing mill line are collected from the strip trapped among the production mills by freezing the growing scale on the strip by the melt glass coating and shutting down the line simultaneously. The samples observed of its cross sectional figure showed the process of scale defect formation where the defects are formed at the base metal surface by thicker oxidized scale during each rolling passes. The properties of the oxidized layer growth both at rolling and inter-rolling are detected down sized rolling test simulating carefully the rolling condition of the production line. The thickness of the oxidized layer at each rolling pass are simulated numerically. The critical scale thickness to avoid the defect formation is determined through the expression of mutual relation between oxidized layer thickness and the lanks of the strip called quality for the scale defects. The scale growth of scale less than the critical thickness and also to keep the bulk temperature tuning the water flow rate and cooling time appropriately. Two units of Inerstand Cooler are designed and settled among the first three stands in the production line. Two units of scale defect is counted from the recoiled strip and the results showed distinct decrease of the defects comparing to the conventionaly rolled products.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.126-132
• /
• 1996

A laboratory scale hot strip rolling wear simulator(HRWS) was developed for the purpose of investigating the tribological phenomena occurred in production hot strip rolling mills. The HRWS' main parts are the electric heater, the mechanical descaler, tandem type 2-4Hi rolling mill stands, the cooling chamber, the tension controller and coiler. By simulating the tribelogical phenomena in rolling process at laboratory, wear patterns, cracks, cat-ear wear, black film, effect of hot rolling oil lubrication, etc. were reproduced, and discussed on the performace of simulator.