• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1410-1417
• /
• 2006

The metal processing system usually consists of various components such like motors, work rolls, backup rolls, idle rolls, sensors, etc. Even a simple fault in a single component in the system may cause a serious damage on the final product. It is therefore necessary to diagnose the faults of the components to detect and prevent system failure. Especially, the defects in a work roll are critical to the quality of strip. It is especially difficult to detect faults of a roll by using the existing frequency analysis method if the speed of the roll is changing. In this study, a new diagnosis method for roll eccentricity under the roll speed changes was developed. The new method was induced from analyzing the rolling mechanism by using rolling force models, radius-speed relationship, and measured rolling force, etc. Simulation results by using the field data show that the proposed method is very useful.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.156-159
• /
• 2003

Surface normal vector and surface velocity are very important parameters to simulate rolling processes precisely. In this study, Local displacement functions are constructed for each node on the contact surface and parameters are found by the least square fitting of displacement on the neighbor nodes. Deformation gradient tensor is calculated from the displacement function and surface normal vector and velocity also can be derived. Flat rolling simulation model is presented on the basis of the suggested contact scheme. Series of rolling process simulation are carried out and the results are compared with the experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.403-407
• /
• 2005

This paper proposes a looperless tension control algorithm which is robust to disturbance and tensional variation in rolling process using SVR(Support Vector Regression). Hot rolling process which is global technology to coil steel after continuous finishing process for welded bars followed by roughing mill process, becomes hot issue. Finishing mill process not only makes it possible to produce ultra thin steel strip(0.8 mm) but enhance the quality of terminals of coil, which increases the productivity due to faster process. Constant tension control between stands in hot rolling process is essential to enhance the quality of steel. Sensorless tension control is under research by some advanced companies to replace the conventional tension control method because in continuous finishing mill process, it is impossible to install the looper used in conventional control system. Simulation results show the effectiveness of the proposed algorithm.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1193-1201
• /
• 1993

A new deformation resistance model for hot steel strip rolling process was formulated to improve the accuracy of roll force estimation. To improve the existing deformation resistance model more precisely, a modification function was introduced in this study. For the modification function, several factors considering material and operational conditions have been investigated and the optimal modification function was determined under the principle of minimum variability. The newly formulated modification function was applied to the deformation resistance model for ultra-low carbon steel and showed improved accuracy with about 30% decrease in terms of standard deviation of predicted roll force values against measured ones.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.1
• /
• pp.34-41
• /
• 2016

Bar camber is a phenomenon in which a material with a deformation gradient across its width is bent in the right or left direction in the roll gap. This paper proposes a dynamic setup approach for a side guide for reducing bar camber. A bar tracking scheme using a rotary encoder was adopted to fix an operation point for the side guide. The guiding pressure was utilized for measuring the actual width of the bar with camber. Based on the accurate position and width of the bar, the side guide was dynamically set and operated at the actual roughing train in a hot strip rolling mill. The amount of camber was reduced notably when the dynamic setup scheme was installed in the side guide. 78% of the bars tested had a camber in the range of ${\pm}20mm$, which was an improvement of 27% in terms of production yield.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.819-827
• /
• 1992

Investigations of the fatigue damage of roughing mill roll and experimentally. By the computer simulation for analysing the stresses on the roll surface and experimental hot rolling, the following results were drawn : The crakcs observed on the roll surface were initiated thermally in the initial stage of the rolling and propagated by repeated thermal and bending stresses. The size of the roll surface cracks smaller than 4.87mm could avoid the occurrence of tiny scab, surface defect of hot steel strip. Since the size of surface cracks observed on the roughing mill roll was very small, the fatigue damage of roll surface was found not to be the major factor for the formation of the scab.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.189-205
• /
• 1996

The twin-roll type strip continuous casting process(or direct rolling process) of steel materials is characterized by two rotating water cooled rolls receiving a steady supply of molten metal which solidifies onto the rolls. A solidification analysis of molten metal considering phase transformation and thermofluid is performed using finite diffefence method with curvilinear coordinate to reduce computing time and molten region analysis with arbitrary shape. An enthalpy-specific heat method is used to determine the temperatures inthe roll and the steel. The temperature distribution of cooling roll is calculated using two dimensional finite element method, because of complex roll shape due to cooling hole in rolls and improvemnt accuracy of calculation result. The energy equaiton of cooling roll is solved simultanuously with the conservation equaiton of molten metal in order to consider heat transfer through the cooling roll. The calculated roll temperature is compared to experimental results and the heat transfer coefficient between cooling roll surface and rolling material(steel) is also determined from comparison of measured roll temperature and calculated temperature.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.51.2-51
• /
• 1998

• Journal of Korea Foundry Society
• /
• v.22 no.4
• /
• pp.174-183
• /
• 2002

Twin-roll process is a relatively new continuous casting process which can produce high-quality strip products directly, and solidification rate can reach $10^3$ to $10^4$ K/s, leading to fine and uniform microstructures with enhanced mechanical properties. The strip casting condition for producing fine Al-Sn alloy strip was obtained experimentally, and defects appearing on the strip was examined. Crack formation and surface quality of the strip was found to depend mainly on process parameters such as melt temperature, roller gap and rolling speed. Sn structure of network type was observed in Al-20Sn and Al-40Sn alloy strips, and cell spacing of Al-40Sn alloy was smaller than that of Al-20Sn. Banding strength of the heat treated specimens increased with increasing of soaking time and temperature, and bonding strength of Al-20Sn alloy was more superior than that of Al-40Sn alloy. However wear resistance of Al-40Sn alloy contained large amount of soft Sn which possess good anti-friction characteristics was superior than that of Al-20Sn alloy.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.922-930
• /
• 1999

This paper describes a new 14-CPU real-time distributed automatic gauge control (AGC) system for POSCO's No. 2 Hot Strip Mill at Pohang Works. The new AGC system has adopted gaugemeter AGC, Monitor AGC, and roll gap disturbance compensators. The computer system for the new AGC system has been developed based on VMEbus computer systems and a commercial real-time operating system. A VMEbus computer system is also used for the position servo control of hydraulic cylinders. All the application programs and input/output signals have been reasonably distributed over the control computer systems for the maximum reliability and effectiveness of the system. The new AGC system has been successfully used for the No. 2 Hot Strip Mill.