• 소성∙가공
• /
• 제6권4호
• /
• pp.279-290
• /
• 1997

The sectional forming analysis of stamping pocesses for aluminum alloy sheet metals was investigated. For the modeling of the anomalous behavior of aluminum alloy sheet. the Barlat's strain rate potential and Hill's 1990 non-quadratic yield theory with an isotropic hardening rule were employed. The rigid-viscoplastic FEM formulation which solves equilibrium equation for plane-strain stage with mesh-normal geometric constraints was derived. A new method to determine the Barlat's anisotropic coefficients was also suggested. To verify the validity of the formulation, the stretch and draw forming processes of a square cup were simulated.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.109-112
• /
• 2015

This article describes a cellular instability and laminar burning velocity of simulated synthetic natural gas(SNG) including 3% hydrogen. In this study, experimental apparatus is employed using cylindrical bomb combustor, and investigation is carried out with high speed camera and Schlieren system. The cellular instability is caused by the buoyancy, hydrodynamic instability. Unstretched burning velocity can be determined by extrapolated stretch rate of zero point from measured results. These results were also compared with numerical calculation by Chemkin package with GRI 3.0, USC-II, WANG, C3 Fuel mechanism. As an experimental conditions, equivalence ratios was adjusted from 0.8 to 1.3. From results of this work, the one was found that the cellular instability has occurred by effect of thermal expansion rate and flame thickness. As the other results, unstretched laminar burning velocity was best coincided with GRI 3.0 mechanism.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.68-74
• /
• 2000

Experimental investigation on flame spread along suspended droplet arrays have been conducted with various droplet spacings and ambient air velocities. Especially, an opposed air stream is introduced to simulate fundamental flame spread behaviors in spray combustion. High-speed chemiluminescence imaging technique of OH radicals has been adopted to measure flame spread rates and to observe various flame spread behaviors. The fuel used is n-Decane and the air velocity varies from 0 to 17cm/s. The pattern of flame spread is grouped into two: a continuous mode and an intermittent one. It is found that there exists droplet spcings, above which flame spread does not occur. The increase of ambient air velocity causes the limit droplet spacing of flame spread to become small due to the increase of apparent flame stretch. As the ambient air velocity decreases, flame spread rate increases and then decreases after taking a maximum flame spread rate. This suggests that there exists a moderate air flowing to give a maximum flame spread rate due to enhanced chemical reaction by the increase of oxidizer concentration.

• 한국의류학회지
• /
• 제3권2호
• /
• pp.15-22
• /
• 1979

The heat setting of sewing thread is known to have some puckering. In this experiment, the P/C fabrec and polyester thread were heat setted at temperatures ranging from $70^{\circ}C$ to $150^{\circ}C$ at the interval of every $^20{\circ}C$ for the period of 1, 5, 10, 20 and 40 minutes resoectivly. The results obtained are as follows: 1) In general, the pre-laundering sewing shrinkage related negatively to time but related positively to temperature. And it showed the lowest rate at $110^{\circ}C$. 2) In case of slack treatment, the post-laundering sewing sewing shrinkage marked the lowest rate at $130^{\circ}C$ while that of stretch treatment showed the lowest rate at $90^{\circ}C$. 3) The rates of post-laundering sewing shrinkage were higher than those of pre-laundering shrinkage, the difference between them reached the bottom when applied the slack treatment at $130^{\circ}C$ and the streched treatment at $110^{\circ}C$.

• 한국전문물리치료학회지
• /
• 제10권3호
• /
• pp.53-61
• /
• 2003

The purpose of this study was to determine the effects On the lymphedema patients of sponge padding and the correlation between the rate of edema reduction and downward shifting of bandages. Fifty secondary lymphedema patients with no infection, active cancer, limitation of movement, pain or drugs were randomly assigned to two groups: a sponge padding group, and a cotton padding group. Complex decongestive therapy was applied for 2 weeks. In each group the volume of the ankle, mid-calf, knee, and mid-thigh and downward shifting of bandages at the thigh was measured with measuring tape. The reduction of volume and downward shifting of bandages were analyzed by the unrelated t-test and the Pearson Correlation Test. The results were as follows: 1. In comparison between the sponge padding group and the cotton padding group, there was no significant difference in volume except in the thigh area. The edema volume was reduced significantly to $37.77{\pm}31.15%$ at the thigh with sponge padding after treatment (p<.05). 2. Bandage shifted 10.12 cm with cotton padding, but only shifted 2.85 cm when sponge padding was used. Sponge padding had an excellent effect in preventing the shifting of bandages. There was a significant difference in the amount of shifting that occurred with each type of padding (p<.05). 3. There was also a strong correlation between the reduction of edema and the shifting of bandage. These results suggest that short-stretch bandaging with sponge padding is more effective than bandaging with cotton padding. Further study on skin irritation and the comfort of sponge padding is needed to use padding materials safely and effectively.

• 생명과학회지
• /
• 제19권11호
• /
• pp.1568-1574
• /
• 2009

본 연구는 고혈압전단계자들에 대한 지속적인 건 스트레치시 시간에 따른 생리학적 반응을 분석하여 정상혈압자와 고혈압전단계자에 대한 EPR의 한 요소인 기계적 수용기가 혈압 및 혈역학 반응에 어떠한 영향을 주는지를 검토하였다. 그 결과, 안정 시와 시간에 따른 혈압 반응은 고혈압전단계자에 있어 SBP, MAP가 평균 20sec에서 통계적으로 가장 높은 경향을 보였으며(p<0.05), 정상혈압자에서는 SBP, DBP, MAP가 평균 45sec에서 가장 높은 경향을 보였다(p<0.05). 이는 고혈압 전단계자의 지속적인 수동적 건 스트레치 시 정상혈압자에 비해 Group III mechanoreceptors의 역기능에 따른 상승된 혈압 반응이 초기에 나타내었다고 사료된다. 또한 혈역학 반응에서 안정 시와 비교하여 지속적인 수동적건 스트레치 시 고혈압전단계자에서의 HR, SV, CO, TPR 모두 유의한 차이를 보이지 않았으나 정상혈압자에서 SV, CO가 통계적으로 유의한 차이를 보였다(p<0.05). 이는 CO, SV, HR, TPR이 정상혈압자에 비해 고혈압전단계자에 있어 높은 경향을 나타내었지만, 혈역학 반응은 본 연구를 통해 차이를 보이지 않아 앞으로 연구가 필요할 것으로 사료된다.

• 한국의류학회지
• /
• 제29권12호
• /
• pp.1535-1545
• /
• 2005

신축성 소재 여성용 바디수트 원형 설계에 관한 선행연구에서 개발된 바디수트의 진동둘레길이 항목을 적용한 소매원형 제도방법이 제안되었다 본 연구는 선행연구와 연속적 맥락에서, 첫째, 신축성 소재의 물성을 고려한 패턴축소율의 적용을 제시하고 둘째, 그에 따라 개발된 여성용 바디수트 소매원형의 제도방법의 단계별 서술을 통해 교육 및 산업분야에서의 사용을 목적으로 하였다. 본 연구를 위하여 광범위하게 사용되고 있는 기존의 소매원형 제도방법을 우선, 선정하여(i.e. Joseph-Armstrong: T1, Shoben & Ward: T2, Esmod: T3 그리고 Joseph-Armstrong 절충식 : T4) 분석하였다. 그 가운데 소매의 앞 뒤차가 반영되지 않는(i.e. T1) 것과 반영되는(i.e. T2, T3 그리고 T4) 방법으로 나누어 구분하고 그에 따른 바디수트 소매샘플을 선행연구와 동일한 신축성 소재$(wale: 50\%/course: 70\%)$를 사용하여 제작한 후, 5인의 전문평가단을 구성하여 그 외관과 동작적합성을 평가하였다. 외관평가에서 관찰된 항목은 앞, 옆, 뒤 바디수트 소매의 여유분, 중심선의 위치와 소매길이, 그리고 바디수트 몸판과의 조화정도의 총 13항목이었고, 쾌적성 평가에서는 전방수직, 측방수직, 측방수평 3동작을 통해 실험의의 동작적합성을 평가하였으며 최종적으로 외관과 동작성이 적절히 조화된 바디수트 소매원형을 제안하는 과정을 거쳤다. 외관평가에서 T3>T4>T2>T1 순서로 우수하게 평가되었으며, 동작적합성 평가에서는 T1>T4>T2>T3의 순으로 평가되어, 외관적으로는 여유분이 적어 당겨 보이는 이유로 점수가 낮아도 쾌적성에서는 오히려 죄어주는 것이 안정감이 있다고 분석되었다. 따라서 외관과 쾌적감의 균형을 고려하였을 때 최종적으로 T4,즉, 소재의 신축성에 따른 패턴축소율(전체소매길이 : 1.0RR, 소매산높이 : 0.7RR, 팔꿈치둘레: 0.9RR)이 반영되고, 진동둘레에 제로 이즈량을 부가하였으며, 앞뒤차가 반영된 바디수트 소매 원형 제도방법 이 제안되었다.

• 한국화재소방학회논문지
• /
• 제27권6호
• /
• pp.50-56
• /
• 2013

대향류 비예혼합 연료-공기 유동장에서 고온연료의 점화특성과 형성된 화염의 소화특성에 미치는 복사효과에 대해 수치계산을 통해 검토하였다. 화학반응의 계산을 위해 GRI-v3.0의 상세화학반응기구를 사용하였으며, 단열계산과 광학적으로 얇은 복사모델을 적용하여 계산을 수행하였다. 대향류 유동장의 점화와 소화점을 정확히 찾기 위하여 화염제어 연속계산법을 적용하였다. 결과를 통해 스트레인율 변화에 대해 최고 온도보다는 최고 H 라디칼 농도가 점화와 소화거동을 이해하는데 더 적합하다는 것을 확인하였다. 최고 H 라디칼 농도변화 거동을 통해 기존에 알려진 S-곡선, C-곡선 및 O-곡선 등을 확인하였다. 복사열손실 분율($f_r$)과 공간에 대해 적분된 열발생률(IHRR)을 통해 $f_r$이 가장 큰 점에서 복사효과에 의한 소화가 발생하였으며, 화염신장 소화점에서는 IHRR이 가장 높지만 화염에서의 전도에 의한 열손실로 인해 소화가 되는 것을 확인하였다. 복사는 화염신장 소화점에는 거의 영향이 없지만 복사 소화점과 점화점에는 큰 영향을 주는 것을 알 수 있었다. 또한 연료의 온도가 높아질수록 복사에 의한 소화점의 스트레인율과 화염신장에 의한 스트레인율 사이의 영역이 넓어지게 되어 화염 안정성이 향상되고 있음을 알 수 있었다.

• The International Journal of Costume Culture
• /
• 제7권2호
• /
• pp.77-86
• /
• 2004

The purpose of this study is to characterize physical and tensile properties according to a knitting method as basic materials for solving the difficulties that occur due to the fact that the crosswise elongation is most different among knit stitch at the time of measuring elongation of knitwear. The sample used for this study was wool $100\%$ and was knitted into two, that is, controlled loop length controlled to properties of structure and fixed loop length by using Shimaseiki SES-124S 12G computer automatic flat knitting machine with DSCS device. Also, the density of rib fabric was 12gauge and its quantity was a total of seven of $0{\times}0,\;1{\times}1,\;2{\times}1,\;2{\times}2,\;3{\times}3,\;4{\times}4$ and including plain fabric, and knitted 2 pieces of sample of 300 wale${\times}400$ course. In conclusion, rib stitch has the much higher stretch rate in the direction of the course than other stitches.

• 한국연소학회지
• /
• 제10권2호
• /
• pp.9-17
• /
• 2005

WSGGM with gray gas regrouping is successfully applied to study the flame structure of opposed flow flames including effect of radiative transfer. The statistical narrow band model is used to obtain the benchmark solutions. Results obtained by using the optically thin model are shown to overestimate the emission and to predict the flame structures inadequately especially for optically thick and low stretch rate flames. Computed results by using the WSGGM with 10 gray gases and SNB model show reasonable agreements with each other, and the required calculation time for the WSGGM is acceptable for engineering applications.