• 한국염색가공학회지
• /
• 제23권4호
• /
• pp.233-240
• /
• 2011

A fineness range of 150 Nm-170 Nm has recently been applied to produce much finer wool products, so that processing techniques for the wool fabrics have been developed very rapidly. However, the worsted wool-like technique using polyester fiber has not been still implemented in general processing technique. Therefore, this research is to develop materials of side-by-side type with high finess, high shrinkage and stretchability. The mechanical properties of the produced fabrics were analyzed and the fundamental information were obtained for the new worsted wool-like products. The physical properties of a latent crimped yarns of side-by-side type with stretch function are analyzed. Also the mechanical properties of five kinds of fabrics are analyzed, which are produced with non-circular shape(+type) warp yarns of a twist of 1000(T/M) and with two kinds of latent weft yarns of a twist of 1000 T/M and DTY respectively.

• 소성∙가공
• /
• 제12권3호
• /
• pp.202-207
• /
• 2003

In order to examine the springback amount and material properties of aluminum alloy sheets (AL1050 and AL5052) in the warm forming which forms the sheet above the room temperature, the stretch bending and draw bending tests and tensile test in various high temperatures are carried out. The warm forming temperature 15$0^{\circ}C$ is a transition in terms of the material properties: over the forming temperature 15$0^{\circ}C$, them $\sigma$$_{YS}$ , $\sigma$$_{TS}$ , E, K, n, etc. are bigger but $\varepsilon$ and plastic strain ratio are smaller. Below the forming temperature 15$0^{\circ}C$, there are no big differences in material properties as the forming temperature changes. AL5052 sheet has more springback effect than AL1050 sheet. While the springbacks of AL5052 and AL1050 sheets show a big reduction over the warm forming temperature 15$0^{\circ}C$ in the stretch bending test, the springback rapidly reduces in the warm forming temperature 15$0^{\circ}C$-20$0^{\circ}C$ for AL5052 sheet and 20$0^{\circ}C$-25$0^{\circ}C$ for AL1050 sheet in the draw bending test.

• 소성∙가공
• /
• 제11권8호
• /
• pp.668-675
• /
• 2002

The circles deform into various shape during deformation, the major and minor axes of which indicate the direction of the major and minor principal strains. Likewise, the measured dimensions are used to determine the major and minor principal strain magnitudes. This circular grid technique of measuring strains can be used to diagnose the causes of necking and fracture in industrial practice and to investigate whether these defects were caused by material property variation, changes in lubrication, of incorrect press settings. In non-axisymmetric deep drawing, three modes of forming regimes are found: draw, stretch, plane strain. The stretch mode for non-axisymmetric deep drawing could be defined when the major and minor strains are positive. The draw mode could be defined when the major strain is positive and minor strain is negative, and plane strain mode could be defined when the major strain is positive and minor strain is zero. Through experiments the draw mode was shown on the wall and flange are one of a drawn cup, while the plane strain and the stretch mode were on the punch head and the punch corner area respectively, We observed that the punch load of elliptical deep drawing was decreased according to increase of die corner radius and the thickness deformation of minor side was more large than major side.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.487-493
• /
• 2012

To analyze the factors on stretch-flangeability for 980 MPa-grade hot-rolled steels, two types of steels (Fe-Cr and Fe-Mo) were manufactured by hot-rolling. Manufactured steels at the low coiling temperature, such as 400 and $500^{\circ}C$, had poor stretch-flangeability due to un-uniformly distributed carbides and a large deviation of interphase hardness. However, when the coiling temperature was set at $650^{\circ}C$ with Fe-Cr steel, 998 MPa of ultimate tensile strength, 19% of total elongation and 65% of the hole expanding ratio were achieved by microstructural constituents of polygonal ferrite (PF) and granular ferrite (GF) dispersed with fine carbides (<50 nm). Therefore, the material to attain 980 MPa with superior formability was the Fe-Cr steel that was precipitation-hardened in polygonal ferrite and granular ferrite at the coiling temperature $650^{\circ}C$.

• 한국전자파학회논문지
• /
• 제26권2호
• /
• pp.179-188
• /
• 2015

실환경에서 레이더 시스템의 성능 평가를 수행하는 것은 시간이나 비용의 제한조건이 많으므로, 이를 시험하기 위한 표적 신호 모의 장치가 반드시 필요하다. 본 논문은 고해상도의 거리 프로파일 또는 영상을 형성하거나 혹은 추적의 정확도를 올리기 위하여 점차적으로 광대역을 사용하는 레이더의 최신 동향에 따라 이를 시험하기 위한 표적신호 모의방법을 제시하였다. 송신신호를 직접 고속 샘플링하여 디지털 메모리를 이용한 시간 지연을 통해 구현하는 방법과 스트레치 프로세싱을 사용하는 시스템을 위한 비트 주파수 생성을 이용하는 방법에 대하여 기술하고, 각 방법이 광대역 파형의 표적을 모의할 때 가져야 할 조건을 제시하였다. 또한, 디지털 메모리 방식에 비트 주파수를 추가하는 방법을 제시하였다. 시뮬레이션을 통해 제시된 방법을 비교하고 타당함을 보였다.

• 복식문화연구
• /
• 제15권4호
• /
• pp.702-712
• /
• 2007

The purpose of this study was to understand the current trend with regard to the material of jeans and the making method of jeans pattern and the characteristics of washing processing through the overall production status of jeans in casual brands and to offer the basic data for producing the high efficient jeans. The results were as follows. According to the survey of production status of jeans in casual brands, the fabric mixture was highest in the order of non-stretch denim 100% cotton, stretch denim cotton/spandex mix and denim with $1{\sim}2%$ weft direction spandex mix. The most frequently used processing method for denim was in the order of normal finishing, mercerization finishing, soft finishing and pigment finishing. The most frequently used method of washing finishing for jeans was in the order of forming by embossing washing, bio stone washing, normal washing, bio washing, and bio stone bleach washing. The average shrinkage was higher on waist circumference and pants length of warp direction rather than hips circumference, thigh circumference, hem circumference of weft direction.

• Design & Manufacturing
• /
• 제9권3호
• /
• pp.1-8
• /
• 2015

This study presents the preform injection molding and the blow molding of the injection stretch-blow molding process for PET bottles. The numerical analysis of the injection molding and the blow molding of a preform is considered in this paper using CAE with a view to minimize the warpage and the thickness. In order to determine the design parameters and processing conditions in injection/blow molding, it is very important to establish the numerical model with physical phenomenon. In this study, we appropriately predicted the warpage, deformation and thickness distribution along the product walls.

• 소성∙가공
• /
• 제10권2호
• /
• pp.91-100
• /
• 2001

A sectional FEA program is developed lot analyzing forming processes of sandwich sheets, which are intensively used recently as a lightweight material of an automobile body. The aluminum sandwich sheet consists of two aluminum skins and a polyprophylen core in between. The aluminum sandwich sheet is dominantly effected by the bending effects in small radius of curvature, so that an appropriate description of bending effects is required to analyze the forming processes. For the evaluation of bending effects, the bending equivalent forces are calculated from the bending moment computed using the curvature of the tool and are added to the membrane stretch forces. To verify the validity of the developed program the sectional FEA results in stretch/draw forming Processes of a square cup and draw forming Processes of an outer hood panel were compared with the measurements.

• 소성∙가공
• /
• 제16권1호
• /
• pp.3-8
• /
• 2007

Novel compression molding system for preform has been developed in this study. The preforms for injection blow molding and injection stretch blow molding are being manufactured by injection molding. However it contains gate mark that affects the bottom crack in the PET bottle. The compression molded preform does not contain gate mark, thus the appearance quality of bottle has been increased and the residual stress near gate(bottom of the bottle) has been reduced. The thickness distributions, haze, and transmittance are well accepted for the preform. Also, flow characteristics of the resin between a core and cavity could be analyzed through computer simulation.

• 소성∙가공
• /
• 제6권4호
• /
• pp.291-299
• /
• 1997

This paper is concerned with the design of process sequence to form the inner skin of landing gear. The inner skin of landing gear is a part of airplane which is known to be difficult to form its shape. Our study investigates the production method of inner skin and examines the design criteria by three dimensional elastic-plastic finite element method. Based on the results of simulation, design strategy for improving the process sequence is developed using stretch forming process. The final product of inner skin is produced in multi-stage operations with annealing treatment to meet the required capacity of press. The numerical results show that the newly designed process can produce the required part successfully within the design criteria.