• 한국지반신소재학회논문집
• /
• 제2권1호
• /
• pp.57-68
• /
• 2003

Strain-softening model is developed to characterize the interface behavior of geomembrane with geotextile and geosynthetic clay liner(GCL). The model proposed in this research is calibrated by using data from direct shear tests conducted on smooth and textured geomembrane. The research is divided into two regions, pre-peak and post-peak, to take into account of strain-softening effect. Although slight difference between measured and back calculated data is observed under high normal stress, good agreements, in general, are found from back calculations. Especially, good consistency is observed in the case of low normal stress. Based on the results, it can be concluded that the proposed model can be a reasonable constitutive law to figure out the behavior of strain-softening between interfaces of geomembrane. In addition, DSC(Disturbed State Concept) model is also presented for further application in geosynthetic interfaces.

• 비파괴검사학회지
• /
• 제22권1호
• /
• pp.45-52
• /
• 2002

금속복합재료 (MMC) 내부에서의 강화재와 기지재사이의 열팽창계수의 차이에 의해 발생하는 인장잔류응력은 복합재료의 인장강도를 저하시키는 심각한 문제중의 하나이다. 따라서 본 연구에서는 TiNi/A16061 형상기억복합재료내부의 인장잔류응력의 문제를 해결하기 위하여 강화재로써 TiNi 합금을 사용하였다. TiNi 합금은 형상기억효과를 이용하여 복합재료내부에 압축잔류응력을 발생시킴으로써 인장강도를 증가시키는 역할을 한다. 복합재료내부에 압축잔류응력을 발생시키기 위하여 예변형(pre-strain)을 가하였다. 본 연구에서는 예변형의 변화에 따른 압축잔류응력의 영향을 평가하였으며 AE 기법을 이용하여 고온에서의 복합재료의 미시적 손상거동과 예변형의 영향을 평가하였다.

• 한국건설순환자원학회논문집
• /
• 제10권4호
• /
• pp.443-449
• /
• 2022

섬유보강 콘크리트 제조 시 감섬유 대체재료로서 선반 스크랩을 활용하는 것이 효과적이다. 왜냐하면, 선반 스크랩은 철강 제품의 부산물로서 경제적일 뿐만 아니라 강섬유의 조성과 매우 유사하기 때문이다. 본 연구의 목적은 선반 스크랩 보강 모르타르의 압축강도 및 인장거동을 평가한 후 인장거동에 대한 재료모델을 제안하는 것이다. 이를 위하여 물-결합재비 30 % 및 40 %에 각각에 대하여 선반 스크랩을 총 부피비의 1.5 %를 혼입한 선반 스크랩 보강 모르타르를 제작한 후 압축강도 및 인장거동 등의 역학적 특성을 평가하였다. 또한 선반 스크랩 보강 모르타르의 실험 결과를 바탕으로 인장거동에 대한 재료모델을 제안하였으며, 제안한 모델은 실험 결과와 비교적 잘 일치하는 것으로 나타났다.

• 한국해양공학회지
• /
• 제10권1호
• /
• pp.53-64
• /
• 1996

In this paper, rotating bending fatigue tests have been carried out to investigate the growth behabiors of surface fatigue crack initiated from a small artificial surface defect, that might exist in real structures, on 2024-T3 and 6:4 brass. The test results are analysed in the viewpoints of both strength of materials and fracture mechanics, it can be concluded as follows. The effect of a small artificial surface defect upon the fatigue strength is very large. The sensitivity of 2024-T3 on the defect is higher than that of 6:4 brass. The growth behavior of the surface fatigue crack of 2024-T3 is different from that of 6:4 brass. The growth rate of the surface fatigue crack of 2024-T3 is considerably rapid in the early stage of the fatigue life and apt to decrease in the later stage. It was impossible to establish a unifying approach in the analysis of crack growth begabior of 2024-T3 and 6:4 brass using the maximum stress intensity factor because of their dependence on stress level. But if the elastic strain and cyclic total strain intensity factor range were applied to obtain the growth rate of surface fatigue cracks of the materials, the data were found to be nearly coincided.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.366-372
• /
• 1999

The deformation behavior of commercial stainless steels under hot rolling conditions was investigated by means of hot compression tests performed in the temperature range 800$^{\circ}C$ to 1200$^{\circ}C$. The measured flow stress-strain curves were analyzed by using a simple flow stress model. It was found that the reference strength of stainless steels are much higher than that of carbon steel and that nitrogen and molybdenum alloying greatly increases flow stress of austenitic stainless steel. Ferritic and duplex stainless steel showed comparatively low flow stresses. The flow stress model, which correlates the flow stress with temperature and strain rate, was applied to predict roll forces during hot-plate rolling of stainless steels.

• 한국지반공학회논문집
• /
• 제18권5호
• /
• pp.133-141
• /
• 2002

암반파괴의 가장 큰 영향을 미치는 인장강도는 등방의 암석과 횡등방의 암석의 경우는 분명히 다를 것이다. 본 논문에서는 일축압축강도시험에서 횡등방 암석의 탄성정수를 구하고, 간접인장강도시험을 통하여 횡등방 암석의 인장강도와 인장파괴 거동을 분석하였다. 일축압축시험에서 구한 이방성 탄성정수와 간접인장강도시험에서 얻어진 변형률로 시료중앙의 응력집중계수를 구하여, 등방으로 가정하여 구한 인장강도 값과 이방성일때의 인장강도 값을 비교 분석하였다. 실험 결과 횡등방성 암석의 응력집중계수는 층리면의 각도에 따라서 등방재료의 응력집중계수와는 크거나 작은 값을 나타내었다. 횡등방 암석의 인장강도 산정시 등방의 응력집중계수를 사용하는 것은 층리면이 이루는 각도에 따라 인장강도의 과대 혹은 과소 평가됨을 알 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.177-180
• /
• 2003

I-beam composite hollow slabs were proposed for long-span slabs and long-span bridges due to their higher stiffness and strength. However, the behavior of the composite slab is quite complicate and allowable stress design method is used for the design of the slab. In this paper, static tests on the composite hollow slabs were performed and their inelastic behavior was investigated. Ultimate strength of the composite slabs were evaluated and the contribution of each I-beam to the flexural strength of the slab was also estimated using the measured strain distribution. From the results of these experiments, I-beam composite hollow slabs can be designed by strength design method.

• 대한토목학회논문집
• /
• 제4권4호
• /
• pp.49-58
• /
• 1984

연약점토(軟弱粘土)(방콕)의 주기적(週期的) 반복하중(反復荷重)에 의(依)한 거동(擧動)을 구명(糾明)하기 위하여 부교란시료(不攪亂試料)에 대(對)한 일련(一連)의 반복하중(反復荷重)을 이용(利用)한 삼축압축시험(三軸壓縮試驗)을 시도(試圖)했다. 본(本)시험(試驗)은 포속압력(抱束壓力) 및 초기전단응력(初期剪斷應力)을 변화(變化)시켜 가면서 점토(粘土)의 전단변형(剪斷變形), 강도변화(强度變化) 등(等)을 조사(調査) 비교(比較)한다. 그 결과(結果) 초기전단응력(初期剪斷應力)이 증가(增加)함으로써 응력(應力)-변형곡선(變形曲線)은 적은 변화(變化)를 보였고, 반복하중(反復荷重)에 의(依)한 강도변화(强度變化)는 응력비(應力比)로 표현(表現)될 때 포속압력(抱束壓力)이 $1.0kgf/cm^2$이었을 때 더 컸으며, 축차응력(逐差應力)으로 표현(表現)될 경우(境遇)는 포속압력(抱束壓力)이 $1.5kgf/cm^2$이었을 때 크게 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.291-300
• /
• 1994

The influence of elevated temperatures on the mechanical properties of concrete is important for fire-resistance studies and also for understanding the behavior of containment vessel, such as nuclear reactor pressure vessels, during service and ultimate condition. The present study is to clarify the damage/deterioration of concrete structures that are subjected to high temperature exposure. To this end, comprehensive experiments are conducted. The major test variables are the peak temperatures, rate of temperature increase, and sustained duration at peak temperature. The results include weight loss residual compressive strength and stress-strain curve. From those results, residua compressive strength formula and stress-strain relationship are proposed.

• 한국농공학회논문집
• /
• 제47권2호
• /
• pp.63-72
• /
• 2005

In this study, the physical and mechanical properties of steel fiber reinforced lightweight polymer concrete were investigated experimentally with various steel fiber contents. All tests were performed at room temperature, and stress-strain curve and load-deflection curve were plotted up to failure. The unit weight of steel fiber reinforced lightweight polymer concrete was in the range of $1,020{\sim}1,160\;kg/m^3$, which was approximately $50\%$ of that of the ordinary polymer concrete, The compressive strength, splitting tensile strength, flexural toughness and flexural load-deflection curves after maximum load were shown with increase of steel fiber content. The stress-strain curves of steel fiber reinforced lightweight polymer concrete were bilinear in nature with a small transition zone, Based on these results, steel fiber reinforced lightweight polymer concrete can be widely applied to the polymer composite products.