• Journal of Welding and Joining
• /
• 제26권3호
• /
• pp.45-50
• /
• 2008

SM45C steel rods being used generally for power transmission shafts and machine components was selected and welded by Butt-GMAW(Gas Metal Arc Welding) method. An estimation of fatigue life was studied by constructing S-N curve. Fatigue strength of base metal zone showed higher values than one of weld zone in low cycles between $10^4$ and $10^6$cycles. However, significant decrease in fatigue strength of base metal was found around $10^6$cycles, which were almost same as one of heat affected zone. This decrease was attributed that initial residual stress of the steel rods distributed by drawing process was diminished by continually applied load, and resulted in softening of base metal. The fatigue limit of the weld zone was highest in the boundary between deposited metal zone and heat affected zone, and followed by in the order of deposited metal zone, base metal zone, and heat affected zone. Based on these results, it is revealed that the stress for safety design of machine components using SM45C butt-welded steel rods must be selected within the region of the lowest fatigue limit of heat affected zone.

• Structural Engineering and Mechanics
• /
• 제50권1호
• /
• pp.89-103
• /
• 2014

According to experimental studies made so far, design formula of shear characteristics suggested by ISO 22762 and JEAG 4614, representative design code for Lead Rubber Bearing(LRB) shows dependence caused by changes in compressive stress. Especially, in the case of atypical special structure, such as a nuclear power structure, placement of seismic isolation bearing is more limited compared to that of existing structures and design compressive stress is various in sizes. As a result, there is a difference between design factor and real behavior with regards to shear characteristics of base isolation device, depending on compressive stress. In this study, a full-scale low hardness device of LRB, representative base isolation device was manufactured, analyzed, and then evaluated through an experiment on shear characteristics related to various compressive stresses. With design compressive stress of the full-scale LRB (13MPa) being a basis, changes in shear characteristics were analyzed for compressive stress of 5 MPa, 10 MPa, 13 MPa, 15 MPa, and 20 MPa based on characteristics test specified by ISO 22762:2010 and based on the test result, a regression analysis was made to offer an empirical formula. With application of proposed design formula which reflected the existing design formula and empirical formula, trend of horizontal characteristics was analyzed.

• 터널과지하공간
• /
• 제19권2호
• /
• pp.123-131
• /
• 2009

불연속성 암반에 2-Arch 터널을 건설할 경우, 필러에 작용하는 응력분포 특성을 파악하기 위하여 대형 모형실험과 수치해석을 수행하였다. 분석결과, 불연속면이 존재하는 경우에는 필러에 작용하는 하중이 매우 불규칙적으로 발생하였으며, 불연속면 경사의 영향이 큰 것을 확인하였다. 수치해석 결과 필러부에는 굴착단계에 따라 위치별로 큰 응력 차이가 확인되었다. 주목할 점은 터널 굴착시 벽체뿐만 아니라 필러 기초부에도 큰 응력 차이가 발생하였다. 필러 설계시 이러한 응력편차 현상을 신중하게 고려할 필요가 있다.

• 한국도로학회논문집
• /
• 제11권1호
• /
• pp.187-194
• /
• 2009

이 논문에서는 아스팔트 도로 설계에 필요한 기층골재 재료의 비선형 이방성을 고려한 연결함수를 개발하였다. 기층이 비선형 이방성 거동으로 해석되어졌을 경우, 선형 등방성 거동으로 해석되어질 때 나타나는 기층 하부내의 인장력을 감소시켜 보다 현실적인 응력분포를 보이게 된다. 그러나 현재까지 개발된 연결함수들은 대부분 기층이 선형 등방성 거동으로 해석하여 개발된 것이므로, 비선형 이방성 거동을 근간으로 하는 연결함수의 개발이 현실적인 도로 설계를 위해 필요하다. 이 논문에서 개발된 연결함수를 이용하여 도로를 설계한 결과 AASHTO의 연결함수를 이용하여 설계했을 경우보다, 기층 두께가 25mm 감소되는 결과를 보였으며, 이는 AASHTO 도로 설계가 보수적인 설계라는 것을 입증하였다.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.149-154
• /
• 2012

용접구조물에는 외력이 부가되기 이전에 잔류응력이 걸려 있으므로 용접잔류응력 크기 및 분포 상태는 취성파괴, 피로강도, 응력부식균열, 좌굴, 시효변형과 같은 다양한 형태의 손상에 직접적으로 영향을 끼쳐 잔류응력을 정량적으로 해석하기 위한 지속적인 연구가 필요한 실정이다. 본 논문은 비파괴적인 기법 중 레이저를 이용한 전자처리스페클패턴 간섭법을 이용하여 평판 용접시험편의 외부하중에 따른 전체 거동에 잔류응력의 측정 기법을 제시하고자 한다. 용접시험편에 인장 하중을 가하였을 때, 이를 전자처리패턴스페클 기법을 이용하여 측정하였다. 측정된 결과로부터 용접시험편의 모재부와 용접부의 변형률을 측정하고, 이를 이용하여 탄성계수를 측정하였다. 본 논문은 전자처리스페클패턴 간섭법으로 용접시험편의 용접부와 모재부의 변형률의 차이를 이용하여 잔류응력 값을 산출하는 식을 제시하였고, 이를 수치적으로 계산하여 잔류응력 값을 산출하였으며 측정 결과, 모재부에 비해 용접부의 탄성계수가 약 3.7배 높은 약 8.46 MPa로 측정되었다.

• 한국지반공학회논문집
• /
• 제27권2호
• /
• pp.5-15
• /
• 2011

일본에서 개발된 원추형 팽이기초(Top-Base Foundation)와 국내에서 개발된 부양형 팽이기초(Floating Top-Base Foundation)를 대상으로 대표 점토질 연약지반인 저압축성점토, 점토질 실트, 점토질 모래에 타설하여 실내모형실험을 수행하였다. 본 실험을 통해 하중-침하량, 기초측면 히빙량, 지중응력분포 등을 측정하여 두 가지 팽이기초의 성능을 비교 평가하였다. 또한, 단변길이 증가에 따른 침하량 변화를 분석하였다. 실내모형실험 결과 부양형 팽이기초가 지지력 증진, 침하량 저감, 응력분산효과, 측방구속력에 대해서 좀 더 우수한 성능을 발휘하는 것으로 나타났으며, 기초폭증가에 따른 침하량은 팽이기초 $5{\times}5$배열을 기점으로 수렴하였다.

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.544-552
• /
• 2002

Recommended seismic design guide for the flat bottom vortical-cylindrical oil storage tanks in KS B 6225 is presented. Under earthquake excitations, the hydrodynamic pressure exerted on the tank walls produces overturning moment which may cause either a failure of the anchors or a buckling of the tank shell near its base. The basis for establishing design loads due to hydrodynamic pressure is described including seismic zone risk map in Korea, zone coefficients and the essential facilities factor. This procedure for calculating applied compressive stress on the shell base subjecting to seismic load and for estimating the allowable buckling stress is described.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.166-173
• /
• 2001

Recommended seismic design guide for the flat bottom vertical-cylindrical oil storage tanks in KS B 6225 is presented. Under earthquake excitations, the hydrodynamic pressure exerted on the tank walls produces overturning moment which may cause either a failure of the anchors or a buckling of the tank shell near its base. The basis for establishing design loads due to hydrodynamic pressure is described including seismic zone risk map in Korea, zone coefficients and the essential facilities factor. This procedure for calculating applied compressive stress on the shell base subjecting to seismic load and for estimating the allowable buckling stress is described.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.551-555
• /
• 1997

IJnder earthquake excitations, the hydrodynamic pressure exerted on the flat bottom vertical-cylindrical oil storage tank walls produces overturning moment which may cause either a failure of the anchors or a buckling of the tank shell near its base. The basis for establishing design loads due to hydrodynamic pressure is described including seismic zone risk map in Korea. zone coefficients and the essential facilities factor. This procedure for calculating applied compressive stress on the shell base subjecting to seismic load and for estimating the allowable buckling stress is described. And seismic design program for the tanks is presented.

• The Journal of Advanced Prosthodontics
• /
• 제8권2호
• /
• pp.85-93
• /
• 2016

PURPOSE. The purpose of this study was to determine the effect of anchorage systems and palatal coverage of denture base on load transfer in maxillary implant-retained overdenture. MATERIALS AND METHODS. Maxillary implant-retained overdentures with 4 implants placed in the anterior region of edentulous maxilla were converted into a 3-D numerical model, and stress distribution patterns in implant supporting bone in the case of unilateral vertical loading on maxillary right first molar were compared with each other depending on various types of anchorage system and palatal coverage extent of denture base using three-dimensional finite element analysis. RESULTS. In all experimental models, the highest stress was concentrated on the most distal implant and implant supporting bone on loaded side. The stress at the most distal implant-supporting bone was concentrated on the cortical bone. In all anchorage system without palatal coverage of denture base, higher stresses were concentrated on the most distal implant and implant supporting bone on loaded side. CONCLUSION. It could be suggested that when making maxillary implant retained overdenture, using Hader bar instead of milled bar and full palatal coverage rather than partial palatal coverage are more beneficial in distributing the stress that is applied on implant supporting bone.