• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.3
• /
• pp.39-55
• /
• 1992

In this research, a Three Level Decomposition technique has been developed for configuration design optimization of truss structures. In the first level, as design variables, behavior variables are used and the strain energy has been treated as the cost function to be maximized so that the truss structure can absorb maximum energy. For design constraint of the optimal design problem, allowable stress, buckling stress, and displacement under multi-loading conditions are considered. In the second level, design problem is formulated using the cross-sectional area as the design variable and the weight of the truss structure as the cost function. As for the design constraint, the equilibrium equation with the optimal displacement obtained in the first level is used. In the third level, the nodal point coordinates of the truss structure are used as coordinating variable and the weight has been taken as the cost function. An advantage of the Three Level Decomposition technique is that the first and second level design problems are simple because they are linear programming problems. Moreover, the method is efficient because it is not necessary to carry out time consuming structural analysis and techniques for sensitivity analysis during the design optimization process. By treating the nodal point coordinates as design variables, the third level becomes unconstrained optimal design problems which is easier to solve. Moreover, by using different convergence criteria at each level of design problem, improved convergence can be obtained. The proposed technique has been tested using four different truss structures to yield almost identical optimum designs in the literature with efficient convergence rate regardless of constraint types and configuration of truss structures.

• Development and Reproduction
• /
• v.13 no.4
• /
• pp.257-264
• /
• 2009

A neurotoxin, 6-hydroxydopamine (6-OHDA) has been widely used to create animal model for Parkinson's disease (PD) due to its specific toxicity against dopaminergic (DA) neurons. Since DA signals modulate a broad spectrum of CNS physiology, one can expect profound alterations in neuroendocrine activities of both PD patients and 6-OHDA treated animals. Limited applications of 6-OHDA injection model, however, have been made on the studies of hypothalamuspituitary neuroendocrine circuits. The present study was performed to examine whether blockade of brain catecholamine (CA) biosynthesis with 6-OHDA can make any alteration in the transcriptional activities of hypothalamus-pituitary hormone genes in adult male rats. Three-month-old male rats (SD strain) were received 6-OHDA ($200{\mu}g$ in $10{\mu}\ell$ of saline/animal) by intracerebroventricular (icv) injection, and sacrificed after two weeks. To determine the mRNA levels of hypothalamuspituitary hormone genes, total RNAs were extracted and applied to the semi-quantitative RT-PCRs. The mRNA levels of tyrosine hydroxylase (TH), the rate-limiting enzyme for the catecholamine biosynthesis, were significantly lower than those from the control group (control:6-OHDA=1:0.72${\pm}$0.02AU, p<0.001), confirming the efficacy of 6-OHDA injection. The mRNA levels of gonadotropin-releasing hormone (GnRH) and corticotropin releasing hormone (CRH) in the hypothalami from 6-OHDA group were significantly lower than those from the control group (GnRH, control:6-OHDA=1:0.39${\pm}$0.03AU, p<0.001; CRH, control:6-OHDA=1:0.76${\pm}$0.07AU, p<0.01). There were significant decreases in the mRNA levels of common alpha subunit of glycoprotein homones (Cg$\alpha$), LH beta subunit (LH-$\beta$), and FSH beta subunit (FSH-$\beta$) in pituitaries from 6-OHDA group compared to control values (Cg$\alpha$, control:6-OHDA=1:0.81${\pm}$0.02AU, p<0.001; LH-$\beta$, control:6-OHDA=1:0.68${\pm}$0.04AU, p<0.001; FSH-$\beta$, control:6-OHDA=1:0.84${\pm}$0.05AU, p<0.001). Similarly, the level of adrenocorticotrophic hormone (ACTH) transcripts from 6-OHDA group was significantly lower than that from the control group (control: 6-OHDA=1:0.86${\pm}$0.04AU, p<0.01). The present study demonstrated that centrally injected DA neurotoxin could downregulate the transcriptional activities of the two hypothalamus-pituitary neuroendocrine circuits, i.e., GnRH-gonadotropins and CRH-ACTH systems. These results suggested that hypothalamic CA input might affect on the activities of gonad and adrenal through modulation of hypothalamus-pituitary function, providing plausible explanation for frequent occurrence of sexual dysfunction and poor stress-response in PD patients.

• Journal of Oral Medicine and Pain
• /
• v.31 no.3
• /
• pp.199-210
• /
• 2006

The epidemiological researches on the inpatients hospitalized at the oral medicine ward have been continuously carried out since 1970, and most researches have been performed by centering around the oral medicine wards of college hospitals. Numerous specialists have been produced after the establishment of oral medicine, and they have been active in various fields. As dental clinics have gotten bigger, the function of oral medicine in the secondary clinics is being brought out. As admissive channel, case features, case composition and otherwise have not been researched for a long time, the related researches should be carried out from now on. Hereupon, this study was carried out by targeting the 100 inpatients hospitalized at the oral medicine ward of Sun Hospital located in Daejeon Korea, through questionnaire. As the result, the following results were derived. 1. The ages of the inpatients in Sun Hospital were $29.21{\pm}11.31$ on the average; 71 females' mean average was $29.63{\pm}11.29$ and 29 males' mean average was $28.17{\pm}11.48$. In regard of school career, the patients who finished high-school course or higher accounted for 78%; the patients' school career seemed to be relatively high. The patients who complained of temporomandibular pain accounted for the highest proportion with 65%. In motivation to visit this hospital, internet surfing was 11%, mass media was 10%, acquaintance's introduction was 38%. The patients, who were hospitalized at another hospital due to the same symptom, accounted for 56%. The dental clinics, which made the patients visit this hospital, accounted for 20%. The patients, who were previously aware that the present symptom should be treated by oral medicine, accounted for 38%. The patients, who were not aware of the fact in advance, were 62%. The respondents of 51% answered that they were aware of the fact one month or below before hospitalization. 2. The patients, who complained of craniocervical ache, accounted for 58%; the patients, whose ache aches affect dailylife, were 22%. Continuous ache was 14% and intermittent ache was 68%, and dull pain was 23%. 3. Life variations were compared with each other by using SRRS (Social Readjustment Rating Scale). In consequence, the variation within 3 years indicated a significant difference in the both groups but the variation within 6 months did not indicate any differences. 4. In regard of the questionnaire on the incidents happened for a week, the ache-group was compared with the group free from the ache. As the result, the number of strain arisen for a week, the decrease of favorite works and sudden fear indicated a significant difference. Pleasant feeling and the decrease of interests in looks did not indicate a significant difference, but came close to the significance. 5. In the questionnaire on impatience, the ache-group indicated higher value but there was not a significant difference. 6. In the questionnaire on the symptoms caused by stress, the two groups indicated significant differences in the item of 'the teethridge itches and feels a tooth rising' and 'the occiput or the nape is stiff.' In the item 'the inside of the cheek or the teethridge are widely peeled off, accompanied with ache and hemorrhage', 'the face has acne or pimple' and 'headache frequently attacks', a significant difference was not observed but the two groups came close to the significance.

• Journal of Food Hygiene and Safety
• /
• v.13 no.1
• /
• pp.53-61
• /
• 1998

This study was performed to investigate the antiulcer effects of Opuntia dillenii Haw. on the stomach ulcer induced by restraint and water-immersion stress in rats. For this experiment, 48 male Sprague-Dawley strain were used. The experimental groups were divided into four: a control (C) and 3 Opuntia dillenii Haw. treatment groups (E-1, E-2, E-3). Each dose of Opuntia dillenii Haw. was 30 mg/kg bw (E-1), 60 mgfKg bw (E-2) and 120 mg/kg bw (E-3). The rats were allocated to each group by 12 and observed for 4 weeks. The results were as following: 1. The stomach surface pH in each group showed no significant difference, but the values of Opuntia dillenii Haw. treatment groups were higher than the value of the control group. 2. The gastric wall mucus was increased in all Opuntia dillenii Haw. treatment groups compared with the control group. Especially in E-1 difference was higher (p<0.05) and in E-2 difference was significantly higher (p<0.01). 3. At shear rate 11.25, 45.0, 90.0, $225\;sec^{-1}$, whole blood viscosity and plasma viscosity were measured. Most of the values of Opuntia dillenii Haw. treatment groups were low compared with that of the control group. At shear rate 90.0, $225\;sec^{-1}$ the values of whole blood viscosity in E-1 were significantly low (p<0.05) and at shear rate 11.25, $45.0\;sec^{-1}$, more significant (p<0.01). At shear rate 11.25, 45.0, 90.0, $225\;sec^{-1}$ the values of whole blood viscosity in E-2 were significantly low (p<0.01). At shear rate $90.0\;sec^{-1}$ the value of plasma viscosity in E-1 was significantly low (p<0.05) and at shear rate 90.0, $225\;sec^{-1}$ the values of plasma viscosity in E-2 we resignificantly low (p<0.01). 4. Less severe ulcers were obsered in Opuntia dillenii Haw. treatment groups than in the control group. Especially E-1 groups tissues had only slight ulcers and necrosis of tissue was not observed in this group. From the results of this study, it can be concluded that the oral administratio-n of Opuntia dillenii Haw. results in protection of stomach ulcer by stimulating the secretion of gastric mucus and improving the gastric mucosal microcirculation.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.1
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• Journal of the East Asian Society of Dietary Life
• /
• v.18 no.1
• /
• pp.72-79
• /
• 2008

This study investigated the changes in textural characteristics that occurred by adding maltose syrup, dextrin, and sucrose to whole egg gels, by assessing coagulation after cooling. It also examined the optimal NaCl and sucrose concentrations for whole egg gels sensory evaluations, and then studied how the addition of sucrose effected gel formation and textural characteristics under optimal NaCl concentration. The additions of maltose syrup, dextrin, and sucrose, presented some color changes. The greater the addition of maltose syrup or dextrin, the lower the L, a, and b values of the whole egg gel and whole egg liquid, and ultimately the color turned dark bluish green. With increasing additions of sucrose, maltose syrup, and dextrin, the viscosity of the whole egg liquid increased slightly. In terms of the mechanical texture characteristic of the gel, the texture was most elastic with the 0.8% addition of sucrose, and hardness decreased by increasing the ratio of added sucrose. Increasing amounts of maltose syrup resulted in less hardness and SF. And for dextrin, the SF increased up to 2.5 and then decreased, and hardness decreased with increasing amounts of dextrin. Based on sensory evaluations, the 0.8% addition of NaCl was significantly preferred(p<0.05), in terms of salty taste. The overall preference scores indicated that the whole egg gel made with 0.3% sucrose and the optimal NaCl concentration(0.8%) was most preferred, and each sample was significant(p<0.05). Under the optimal 0.8% NaCl concentration increasing the sucrose concentration resulted in a darker egg gel color, in terms the L value. SF, NF, and hardness, which are mechanical texture parameters, were when 0.8% sucrose and the optimal NaCl concentration of 0.8% were added to whole egg liquid, in preparing the whole egg gel.

• Journal of Life Science
• /
• v.25 no.4
• /
• pp.433-440
• /
• 2015

Several studies suggest that regular consumption of walnuts may have beneficial effects against oxidative stress-mediated disease such as cancer. The present study reports the total phenolic and flavonoid contents, together with the antioxidant and antibacterial activities of several solvent extracts (methanol, n-hexane, ethyl acetate, n-butanol, and water) obtained from walnut (Juglans regia L.) green husk. MIC (minimal inhibitory concentration) values of the walnut extracts for 8 human pathogenic bacteria strain were determined using agar dilution method. Antioxidant activity of extracts were assessed using DPPH (1,1-diphenyl-2-picrylhydrazyl) and ABTS (2,2’-azino-bis-(3-ethylbenzothiazoline-6-sulphonic acid)) assays, EC₅₀ of DPPH and ABTS scavenging activities, and determination of total phenolic and flavonoid content and its correlation with DPPH and ABTS scavenging capacities. Among the six extracts, ethyl acetate extract (EtOAc Ex) showed the highest antimicrobial activity at 3.2 mg/ml of MICs against Staphylococcus aureus SG511. Total flavonoids and polyphenol contents of EtOAc Ex were 42.48 mg of quercetin equivalents (QE)/g and 223.25 mg of gallic acid equivalents (GAE)/g respectively. The highest antioxidative potential was shown by the sample extracted with EtOAc Ex (EC₅₀=13.43 μg/ml for DPPH and EC₅₀=41.83 μg/ml for ABTS radical scavenging activity assay). These results showed that J. regia green husk extracts can be used as an easily accessible source of natural antibacterial agents and natural antioxidants.

• Journal of Life Science
• /
• v.26 no.8
• /
• pp.955-962
• /
• 2016

Fish-meat gel is an intermediate product used in a variety of surimi-based seafood. One of the most-used raw materials of fish-meat gel is Alaska Pollock due to its high-quality meat in terms of gel strength and texture. However, increasing demand for fish-meat gel, along with overexploitation of the wild catch Alaska Pollock, has put the industry in need of low-cost sustainable alternative sources for fish-meat gel. Pagrus major (PM) is a widely aquacultured fish known for having white meat that is low in fat. The current study compares the quality of fish-meat gel prepared from aquacultured PM to that of high and mid-grade Alaska Pollock fish-meat gel. Gels were compared in terms of gel strength, texture, color, and protein pattern. Results indicated that fish-meat gels prepared from PM were superior to Alaska Pollock fish-meat gels with regard to gel strength, hardness, springiness, chewiness, cutting strength, and breaking force. In addition, although not matching in quality, PM exhibited a cohesiveness, whiteness, and expressible moisture content comparable to Alaska Pollock of both grades. Protein pattern analysis also showed that PM and Alaska Pollock fish-meat gels had similar protein profiles before and after gel preparation. Therefore, P. major is suggested as a potential substitute for Alaska Pollock in fish-meat gel production.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.