• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국가금학회지
• /
• 제37권1호
• /
• pp.51-62
• /
• 2010

본 연구는 혼합 생균제의 첨가가 산란계와 육계의 생산성과 소장내 미생물, 면역체계에 미치는 영향을 조사하기 위해 실시하였다. 시험 1은 800수의 82주령 산란계(Hy-Line Brown$^{(R)}$)를 5처리로 구성하여 실시하였다. 각각의 처리는 대조구, 항생제구(avilamycin 6 ppm), 생균제 PB-M(Micro-ferm$^{(R)}$) 0.2%구, PB-L (Lactto-sacc$^{(R)}$) 0.1%구, PB-Y(Y University probiotics) 0.2%구로 구성하여, 8반복 반복당 20수씩 완전 임의 배치하여 자유 섭식케 하였으며, 일반적인 점등 관리(자연 일조+조명= 16 h)를 실시하였다. 시험 2에서는 육계(Ross$^{(R)}$) 1,000수를 공시하여 시험 1과 같은 처리로 구성하여 35일간 전기(0~3주), 후기(4~5주)로 나누어 실시하였으며, 처리당 4반복을 두어 반복당 50수씩 나누어 배치하였다. 시험 1에서는 계란 생산지수들 즉 일계 산란율과 생산지수, 난중, 연파란율, 사료 섭취량, 사료 요구율은 처리구 사이에서 유의적인 차이가 없었다. 강도와 난각 두께는 유의적인 차이가 있었는데, 항생제구와 생균제 처리구에서 증가하는 경향이 있었다. PB-Y구는 난각 강도, 난각 두께, 난각색, 난황색, Haugh unit에서 가장 높았는데 유의한 영향은 미치지 못했다. 시험 2에서는 전기간(0~5주) 증체량 및 폐사율은 처리구 사이에서 유의적인 차이는 없었지만, 0~3주 기간동안 PB-Y의 증체량이 대조구와 항생제구와 비교하여 낮게 나왔다. 전기간(0~5주)에서 항생제구의 사료 섭취량, 생산지수는 가장 높았고, 사료 요구율은 대조구보다 낮게 나왔다. 생균제 처리구들은 대조구와 비교하여 사료 섭취량과 사료 요구율에서는 유의적인 차이가 없었다. 시험 1에서 백혈구 수치 즉, 백혈구, 호중구, 림프구, 단핵구, 호산구, 스트레스지수는 산란계에서 유의적인 차이가 있었다. 항생제구와 생균제구는 모든 수치에서 증가하는 경향을 보였다. 시험 2에서는 오직 스트레스지수에서만 항생제구에서 유의적으로 감소하는 경향을 보였다. 시험 1에서 IgG 농도는 PB-M과 PB-L구에서 유의적으로 증가하였다. E. coli 수는 항생제구, PB-L구, 그리고 PB-Y구에서 유의적으로 감소하였다. 시험 2에서 조지방 이용률이 생균제 처리구에서 유의적으로 감소하였다. 결론적으로 산란계에서는 생균제의 처리구들에서 난각 두께와 강도가 증가하였고, 육계에서는 생산 지수는 증가하고, 사료 요구율은 감소하였다. 백혈구 지수는 산란계에서 항생제와 생균제 처리구에서 증가하는 경향이 있었다. E. coli는 산란계에서 감소하는 경향을 보였으며, 육계에서는 생균제 처리구들이 조지방 이용률에서 감소하는 경향을 보였다. 혈액지수와 소장내 미생물은 육계보다 산란계에서 더 예민하게 반응하는 경향을 보였다.

• 한국방재학회 논문집
• /
• 제8권6호
• /
• pp.53-60
• /
• 2008

일반적으로 연속경간을 가지는 강합성 I-형강 교량에 있어서 내부 지점 부근에서 상대적으로 큰 부모멘트가 발생하므로, 이에 경제적인 단면 활용을 위하여 변단면을 적용하여 휨강도를 증가시킨다. 본 연구에서는 기존 횡-비틀림 좌굴식에 관한 연구를 토대로 하여 비탄성 구간에 있는 계단식 I형보의 횡-비틀림 좌굴강도를 유한요소해석프로그램 ABAQUS(2007)를 이용하여 산정하고, 간편한 설계식을 제안하고 있다. 양단 및 일단 계단식 단면변화를 가지는 보에 대해서 고려하였으며, 플랜지 길이방향 비, 너비방향 비, 두께의 비로 계단식 I형보를 나타내었다. 해석에 사용된 단면매개변수는 각각 27가지 및 36가지 조합이며, 비탄성 횡-비틀림 거동을 고려하기위하여 잔류응력 및 초기결함을 고려한 비선형해석을 실시하였는데, Pi와 Trahair(1995)가 고려한 잔류응력의 형상과 국내 I형강 표준 치수 허용치에 근거하여 부재 길이의 0.1%를 초기제작오차로 고려하였다. 해석모델의 양쪽 끝단에는 모멘트하중을 재하하였다. 개발 제한된 식은 선형 모멘트 하중이 작용할 때 적용가능한 식으로 경제적이고 합리적인 설계에 적극 활용될 수 있을 것이며, 다양한 하중을 받는 계단식 단면 변화보의 비탄성 좌굴강도 연구에 활용될 수 있을 것이다.

• 한국지반공학회지:지반
• /
• 제12권3호
• /
• pp.127-148
• /
• 1996

최근에 들어 사면이나 사면 근처에 교대등과 같이 기초하중이 비교적 큰 구조물들이 시공되는 예가 점차 많아지는 경 향을 보이고 있다. 그러나 일반적으로 사면 또는 사면 근처 에 설치되는 기초의 경우는 수평지반에 비해 지지력이 현저하게 떨어지기 때문에, 말뚝이나 케이슨 등과 같은 고가의 깊은기초들이 주로 사용되고 있는 실정이다. 따라서 토목섬유 또는 metal strip등의 보강재를 이용하여 사면을 보강하는 경제적인 공법이 필요시 되고,또한 이와같은 공법에 관련된 합리적인 기초지지력 해석법의 제시가 요구되고 있다. 본 연구에서는 사면 근처에 설치되는 얕은 기초의 지지력 보강을 목적으로 strip등의 보강재를 설치할 경우, 'wide slab effect' 개념등 Huang및 Binquet-Lee등이 모형실험등을 통해 제시한 파괴매카니즘 및 Boussinesq해법 등을 토대로 하여 보강사면에 대한 기초지지력 해석법을 제시하였다. 본 해석법에서는 soil dilatancy 등의 영향에 의한 깊이별 보강재-주변흙 사이의 마찰계수 변화를 함수형태로 표현하여 보강재주변흙 사이의 상호작용을 부분적으로 고려하였으며, 아울러 본 연구를 통해 제시된 기초지지력 해석법의 적합성 검토를 위해 Huang등이 제시한 모형실험결과와 서로 비교하였다. 이외에도, 설계에 관련된 여러 변수들이 기초지지력에 미치는 영향에 대해서도 분석이 이루어졌다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제16권7호
• /
• pp.952-961
• /
• 2003

In the first part of the study, rates of estrus occurrence and success of A.I. service in the Thai-native and Friesian crossbred, and purebred Friesian cows fed in the National Dairy Training and Applied Research Institute in Chiang Mai, Thailand were traced monthly throughout a year. An electric fan and a water sprinkler cooled the stall for the purebred cows during the hot season (March-September). Both rates in pure Friesians were at their highest in the cold-dry season (October- February), but they decreased steadily during the hot-dry season (March-May) and were at their lowest in the hot-wet season (June-September). Seasonal change of a similar pattern was observed in the incidence of estrus, but not in the success rate of insemination in the crossbred cows. By the use of reproductive data, compiled in the same institute, on the 75 % cross- and purebred Friesian cows, and climatological data in Chiang Mai district, effects of ambient temperature and humidity on the reproductive traits of cows were examined by regression analysis in the second half of the study. Significant relationships in the crossbred, expressed by positive-linear and parabola regressions, were found between reproductive parameters such as days to the first estrus (DTFE), A.I. service (DTFAI), and conception, the number of A.I. services required for conception and some climatic factors. However, regarding this, no consistent or intelligible results were obtained in purebred cows, perhaps because electric fans and water sprinklers were used for this breed in the hot season. Among climatic factors examined, the minimum temperature (MINT) in early lactation affected reproductive activity most conspicuously. As the temperature during one or two months prior to the first estrus and A.I. service rose, DTFE and DTFAI steadily became longer, although, when MINT depleted below $17-18^{\circ}C$, the reproductive interval tended to be prolonged again on some occasions. The maximum temperature also affected DTFE and DTFAI, but only in limited conditions. The effect of humidity was not clear, although the inverse relationship between DTFE and minimum humidity during 2 months before the first estrus in the crossbred seemed to be significant. Failure to detect any definite effect of climate on the reproductive traits of pure Friesians seemed to indicate that forced ventilation by electric fans and water sprinklers were effective enough to protect the reproductive ability of this breed from the adverse effects of a hot climate.

• Asian-Australasian Journal of Animal Sciences
• /
• 제27권5호
• /
• pp.749-756
• /
• 2014

The present study was carried out to investigate the effects of dietary antioxidants on pro-inflammatory cytokines, heat shock protein (HSP) and antioxidant status in broiler chicks under summer conditions. A total of 162, 3-d-old broiler chicks were randomly assigned to a basal diet (CON) and the basal diet supplemented with vitamin C (200 mg/kg diet, VCD) or vitamin E (100 mg/kg, VED) until 35 day of age. All birds were exposed to summer diurnal heat stress at average daily fluctuations of temperature between $32^{\circ}C$ to $34^{\circ}C$ at day to $27^{\circ}C$ to $29^{\circ}C$ at night for the entire feeding periods. There was no significant difference in body weight, feed to gain ratio and the relative organ weight except the thymus in response to dietary vitamin C or E supplementation. However, the mRNA expression of interleukin (IL)-$1{\beta}$, IL-6, interferon (IFN)-${\gamma}$, Toll like receptor (TLR)-4 and HSP70 in the liver of birds fed diet containing vitamin C significantly (p<0.05) decreased compared with those in birds fed basal diet. Dietary vitamin E also showed a significant (p<0.05) decrease in the mRNA expression of IL-6 and HSP70 compared with a basal diet. Total antioxidant status (TAS) in serum of birds fed vitamin C supplemented diet was significantly (p<0.05) higher with than that in birds a basal diet. Lipid peroxidation in serum and liver resulted in a significant (p<0.05) decrease in response to dietary vitamin C or E supplementation. In conclusion, dietary supplementation with antioxidant vitamins, especially vitamin C resulted in a significant decrease in the mRNA expression of pro-inflammatory cytokines and HSP70, and higher antioxidant parameters than that of birds on the basal diet under summer conditions.

• 한국전산구조공학회논문집
• /
• 제20권1호
• /
• pp.75-82
• /
• 2007

본 연구에서는 설계민감도 해석기법을 사용하여 구조물의 안정성, 즉 좌굴을 고려한 형상 최적설계를 수행하였다. 형상 변수를 고려한 설계민감도 해석을 수행하기 위해 전미분 개념을 도입하고, 이를 이용하여 연속체기반의 변분방정식을 미분하여 민감도공식을 유도하였다. 기존의 유한차분법과 비교할 때 설계민감도 해석법의 장점은 설계변수의 갯수에 상관없이 매우 적은 해석횟수를 가지고도 민감도를 더 정확하게 계산할 수 있으며, 해석결과만을 이용하여 민감도계산을 수행하므로 상용 해석 소프트웨어를 활용할 수 있다는 것이다. 한편 좌굴문제를 다룰 때는 일반적으로 보나 쉘 같은 구조요소를 이용하지만 본 연구에서는 솔리드 요소를 이용한 연속체 모델로 고려하였는데 그 이유는 연속체 모델을 이용하면 뚱뚱한 형상뿐만 아니라 보나 쉘 같은 슬림(slim) 한 모델을 모두 해석할 수 있기 때문이다 설계민감도를 활용하여 여러 가지 좌굴문제에 대해 형상 설계민감도 계산 및 최적설계를 수행하였다. 그 결과 실행함수가 매우 빠르게 수렴하는 것을 확인할 수 있었고, 설계변수가 많아지고 해석시간이 길어질수록 더 효율적인 것을 알 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권2호
• /
• pp.13-23
• /
• 2017

본 연구는 사각형 콘크리트 압축부재를 CFRP 쉬트로 감쌌을 때의 보강효과와 거동 특성에 대한 연구로, CFRP 쉬트로 보강한 경우 쉬트의 구속효과에 의하여 압축내력이 향상되었으나 사각형 단면이므로 원형단면보다 구속효과는 작게 나타났다. 보강효과와 거동특성을 확인하기 위하여 CFRP 쉬트의 보강겹수, 시험체의 크기, 형상비, 모따기, 및 단면 개량을 변수로 선정하여 실험을 계획하였다. 11개의 실험변수별로 각각 5개씩, 총 55개의 실험체를 제작하여 실험하였다. 압축시험결과 CFRP 쉬트의 구속에 의해 보강효과가 나타났으나 실험체의 크기가 증가함에 따라 구속효과는 떨어졌다. 반면에 CFRP 쉬트의 구속효과에 의하여 사각형 콘크리트 기둥의 연성은 매우 크게 증가되었다. 단면형상을 사각형에서 원형으로 변형한 경우 압축강도와 연성 모두 증가되었다. 또한 실험결과와 기존연구결과를 사용하여 CFRP로 구속된 사각형 콘크리트 부재에 대한 기존 강도추정식의 정확성과 신뢰성을 검증하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.144.2-144.2
• /
• 2016

Diamond-like carbon (DLC) coatings have been widely applied to the mechanical components, cutting tools due to properties of high hardness and wear resistance. Among them, hydrogenated amorphous carbon (a-C:H) coatings are well-known for their low friction properties, stable production of thin and thick film, they were reported to be easily worn away under high temperature. Non-hydrogenated tetrahedral amorphous carbon (ta-C) is an ideal for industrial applicability due to good thermal stability from high $sp^3$-bonding fraction ranging from 70 to 80 %. However, the large compressive stress of ta-C coating limits to apply thick ta-C coating. In this study, the thick ta-C coating was deposited onto Inconel alloy disk by the FCVA technique. The thickness of the ta-C coating was about $3.5{\mu}m$. The tribological behaviors of ta-C coated disks sliding against $Si_3N_4$ balls were examined under elevated temperature divided into 23, 100, 200 and $300^{\circ}C$. The range of temperature was setting up until peel off observed. The experimental results showed that the friction coefficient was decreased from 0.14 to 0.05 with increasing temperature up to $200^{\circ}C$. At $300^{\circ}C$, the friction coefficient was dramatically increased over 5,000 cycles and then delaminated. These phenomenon was summarized two kinds of reasons: (1) Thermal degradation and (2) graphitization of ta-C coating. At first, the reason of thermal degradation was demonstrated by wear rate calculation. The wear rate of ta-C coatings showed an increasing trend with elevated temperature. For investigation of relationship between hardness and graphitization, thick ta-C coatings(2, 3 and $5{\mu}m$) were additionally deposited. As the thickness of ta-C coating was increased, hardness decreased from 58 to 49 GPa, which means that graphitization was accelerated. Therefore, now we are trying to increase $sp^3$ fraction of ta-C coating and control the coating parameters for thermal stability of thick ta-C at high temperatures.

• 터널과지하공간
• /
• 제24권5호
• /
• pp.366-372
• /
• 2014

일반화된 Hoek-Brown (H-B) 식은 절리성 현장암반에 적용되는 암반공학 고유의 파괴조건식이다. 이 파괴조건식에서는 현장암반의 GSI 값을 이용하여 무결암의 강도정수를 현장암반의 값으로 변환시킨다. 현장암반의 특성을 체계적으로 고려한 거의 유일한 암반파괴조건식이라는 측면에서 일반화된 H-B 파괴조건식은 적용범위를 넓혀가고 있지만 비선형 함수라는 단점을 가지고 있다. 이에 따라 일반화된 H-B 식을 선형 Mohr-Coulomb (M-C) 파괴조건식의 틀로 이해하려는 연구들이 시도되고 있다. 이 연구에서는 일반화된 H-B 식에 응력무차원화 변환을 적용하여 접선점착력을 접선마찰각의 함수로 표현하는 명시적 관계식을 유도하였다. 유도된 관계식을 이용하여 암반 질의 변화에 따른 일반화된 H-B 식에 내포된 접선마찰각 - 접선점착력 변화 특성을 고찰하였다. GSI 값의 변화만을 고려한 경우 GSI 값의 증가에 따라 접선마찰각은 감소하고 접선점착력은 증가하는 경향을 보였다.