• 열처리공학회지
• /
• 제24권6호
• /
• pp.311-317
• /
• 2011

The effect of strain rate on the yield stress of an Al-Li alloy has been investigated at temperatures between 77 and 523 K and over the strain rate range from $1.77{\times}10^{-4}s^{-1}$ to $1.77{\times}10^{-2}s^{-1}$. At testing temperatures below 373 K, the yield stress is almost independent of strain rate at any aging stage. At testing temperatures above 373 K, the yield stress increases linearly with the logarithm of strain rate, and the strain rate dependence increases with increasing testing temperature. The yield stresses of under-aged alloy at temperatures between 373 and 473 K at high strain rates are greater than the yield stress at 77 K. For the alloy under-aged or aged nearly to its peak strength, the temperature range within which the positive temperature dependence of yield stress appears expands to the higher temperature side with increasing strain rate. The strain rate dependence of the yield stress is slightly negative at this aging stage. The yield stress of the over-aged alloy decreases monotonically with decreasing strain rate and with increasing testing temperature above 373 K. The modulus normalized yield stress is nearly constant at testing temperatures below 373 K at any strain rate investigated. And, strength depends largely both on the aging conditions and on the testing temperature. The peak positions in strength vs. aging time curves shift to the side of shorter aging time with increasing testing temperature. For the specimens aged nearly to the peak strength, the positive temperature dependence of yield stress is observed in the temperature range. The shift of peak positions in the aging curves are explained in terms of the positive temperature dependence of cutting stress and the negative temperature dependence of by-passing stress.

• 한국해양공학회지
• /
• 제12권1호
• /
• pp.39-49
• /
• 1998

In this work, fatigue tests by axial loading were carried out to investigate the effect of stress ratio on the growth behaviors of surface fatigue crack for SM45C steel and Al 2024-T4 alloy. The growth behaviors of surface crack have been monitored during fatigue process by measuring system attached CCTV and monitor. When the growth rates of surface crack were investigate by the concept of LEFM based on Newman-Raju's .DELTA.K, the dependence of stress ratio appears both SM45C steel and Al 2024-T4 alloy. Therefore, modified stress intensity factor range, .DELTA.K' [=(1+R)/sup n/.DELTA.K] are intorduced to eliminate the dependence of stress ratio. Using .DELTA.K', it is found that the dependence of stress ratio disappears both SM45C steel and Al 2024-T4 alloy.

• Asian Pacific Journal of Cancer Prevention
• /
• 제17권2호
• /
• pp.829-833
• /
• 2016

Purpose: To investigate the work associated stress and nicotine dependence among law enforcement personnel in Mangalore, India. Materials and Methods: A cross-sectional questionnaire survey was conducted among law enforcement personnel in Mangalore, India. Demographic details, stress factors experienced at work and nicotine dependency were the variables studied. The extent of stress factors experienced at work was assessed using the Effort-Reward Imbalance scale (ERI). Nicotine dependence was measured using the Fagerstrom Test for Nicotine Dependence (FTND) and the Fagerstrom Test for Nicotine Dependence-Smokeless Tobacco (FTND-ST). Logistic regression was used for the statistical analysis. Results: Three hundred and four law enforcement personnel participated in the study, among whom 68 had the presence of one or more habits like tobacco smoking, tobacco chewing and alcohol use. The mean effort score was $15.8{\pm}4.10$ and the mean reward and mean overcommitment scores were $36.4{\pm}7.09$ and $17.8{\pm}5.32$ respectively. Effort/Reward ratio for the total participants was 1.0073 and for those with nicotine habit was 1.0850. Results of our study demonstrated no significant association between domains of ERI scale and presence of habits but work associated stress was associated with the presence of one or more habits. Compared to constables, head constables had 1.12 times higher risk of having a nicotine habit. Conclusions: Our study implies job designation is associated with nicotine habits. However, there was no association between work associated stress and nicotine dependence among law enforcement personnel in Mangalore.

• 정신신체의학
• /
• 제12권1호
• /
• pp.47-55
• /
• 2004

연구목적: 알콜 의존 환자의 우울 증상과 스트레스에 대한 반응과 감정표현불능증에 대하여 알아본 후, 상관관계에 대하여 조사하여 향후 환자의 삶의 질을 높일 수 있는 치료적 중재를 위한 기초 자료로 사용하고자 본 연구를 시행하였다. 방 법: 알콜 의존으로 진단을 받은 환자 94명과 정신과 치료 경험이 없는 사람 34명을 대상으로 하여 한국우울증척도와 스트레스 반응 척도와 감정표현불능증 척도를 시행하였다. 결 과: 우울 증상과 스트레스 반응 요인과 알콜 의존 지수가 알콜 의존 환자의 감정표현불능증 전체 변이 중에 약 55%를 설명하였으며, 이 중 스트레스에 대한 반응이 가장 큰 설명력을 보였다. 결 론: 우울 증상, 스트레스에 대한 반응, 학력, 음주 회수 등이 알콜 의존 환자의 감정표현불능증과 가장 밀접한 관련이 있는 요인으로 밝혀졌으며, 환자가 경험하는 신체화 증상을 포함한 우울 증상과 스트레스에 대한 정신과 의사의 관심이 필요함을 시사하는 것으로, 알콜 의존 환자의 우울 증상과 감정표현불능증에 대한 적극적 치료를 통하여 궁극적으로 환자의 삶의 질을 높일 수 있도록 하는 정신과 의사의 노력이 필요하리라 본다.

• Nuclear Engineering and Technology
• /
• 제54권3호
• /
• pp.1071-1084
• /
• 2022

The present study aims to investigate the dynamic properties of a novel isolation system composed of separate rubber and wire isolators. The testing program comprised pure compressive, pure-shear, compressive-stress dependence, and shear-strain dependence tests that used full-scale test specimens according to ISO 22762-1. A total of 22 test specimens were fabricated and investigated. Among the tests, the pure compressive test was a destructive test that reached up to the failure stage, whereas the others were nondestructive tests before the failure stage. Similar to the pure-shear test, at each compressive-stress level in the compressive dependence test or at each shear-strain level in the shear-strain dependence test, the cyclic loading was conducted for three cycles. In the nondestructive tests, examination of the dynamic shear properties in the X-direction was independent of the Y-direction. The test results revealed that the increase in the shear strain increased the energy dissipation but decreased the damping ratio, whereas the increase in the compressive stress increased the damping ratio. In addition, a macro model was developed to simulate the load-displacement response of the isolation systems, and the prediction results were consistent with the experimental results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.102-105
• /
• 1997

The thickness dependence of stress voltage oxide currents has been measured in oxides with thicknesses between 10nm and 80nm. The oxide currents were shown to be composed of stress current and transient current. The stress current was caused by trap assited tunneling through the oxide. The transient current was caused by the tunneling charging and discharging of the trap in the interfaces. The stress current was used to estimate to the limitations on oxide thicknesses. The transient current was used to the data retention in memory devices.

• 한국안전학회지
• /
• 제8권4호
• /
• pp.27-40
• /
• 1993

High temperature tensile tests, steady state creep tests, Internal stress tests and creep rupture tests using A17075 alloy( $T_{6}$ ) were performed over the temperature range of 9$0^{\circ}C$~50$0^{\circ}C$ (0.4 $T_{m}$ ~0.85 $T_{m}$ ) and stress range of 0.64~17.2(kgf/$\textrm{mm}^2$). The main results obtained in this paper were as follows. (1) The activation energies for yielding at the temperature of 0.4 $T_{m}$ ~0.75 $T_{m}$ were calculated to be 25.7~36.5kcal/mol, which were nearly equal to the activation energies for creep. (2) At around the temperature of 9$0^{\circ}C$~12$0^{\circ}C$ and under the stress level of 10~17.2(kgf/$\textrm{mm}^2$), and at around the temperature of 200~41$0^{\circ}C$ and under the stress level of 1.53~9.55(kgf/$\textrm{mm}^2$) and again at around the temperature of 470~50$0^{\circ}C$ and under the stress level of 0.62~l.02(kgf/$\textrm{mm}^2$), the applied stress dependence of steady state creep rate $n_{measu}$ measured were, respectively, 3.15, 6.62 and 1.1, which were in good agreement the calculated stress dependence $n_{ealeu}$ obtained by the difference of the applied stress dependence of the Internal stress and the ratio of the internal stress to the applied stress. (3) At the temperature range of 0.4~0.43 $T_{m}$ , and at the temperature range of 0.52~0.75 $T_{m}$ and again at the temperature range of 0.82~0.85 $T_{m}$ , the activation energies $Q_{measu}$ obtained by steady state creep rate, respective, 26. 16, 34.9, 36.2 and 36.1kcal/mol, which were in good agreement with those obtained with the activation energies under constant effective stress and the temperature dependence of Internal stress. (4) At the temperature range of the 0.52~0.73 $T_{m}$ and under the stress level of 1.53~9.55(kgf/$\textrm{mm}^2$), the stress dependence of rupture life(n’) measured was 6.3~6.6, which was in good agreement with the stress dependence of steady state creep rate(n). And at the same condition the activation energy for rupture( $Q_{f}$ ) measured was 32.0~36.9kca1/mol, which was also in good agreement with the activation energy obtained by steady state creep rate ( $Q_{c}$ ). (5) The rupture life( $t_{f}$ ) might be represented by athermal process attributed to the difference of the applied stress dependence of the internal stress and the ratio of the internal stress to the applied stress, and the thermal activated process attributied to the temperature dependence of the internal stress as $t_{f}$ = A'$\sigma$$_{a}$ ｛n(1-d $\sigma$$_{i}$ /d $\sigma$$_{a}$ )/(1-$\sigma$$_{i}$ / $\sigma$$_{a}$ )｝.exp[｛ $Q_{c}$ $^{*}$-( $n_{o}$ R $T^2$/ $E_{(T)}$) (d $E_{(T)}$/dT) - ( $n_{0}$ R $T^2$/ $\sigma$$_{a}$ - $\sigma$$_{i}$ ) (d $\sigma$$_{i}$ /dT)｝/RT]. (6) The relationship betwween Larson-Miller rupture parameter and logarithmic stress was linearly decreased, so creep rupture life of Al 7075 alloy seemed to be predicted exactly with Larson-Miller parameter.meter.

• Advanced Composite Materials
• /
• 제18권3호
• /
• pp.265-285
• /
• 2009

Off-axis compressive deformation behavior of a unidirectional CFRP laminate at high temperature and its strain-rate dependence in a quasi-static range are examined for various fiber orientations. By comparing the off-axis compressive and tensile behaviors at an equal strain rate, the effect of different loading modes on the flow stress level, rate-dependence and nonlinearity of the off-axis inelastic deformation is elucidated. The experimental results indicate that the compressive flow stress levels for relatively larger off-axis angles of $30^{\circ}$, $45^{\circ}$ and $90^{\circ}$ are about 50 percent larger than in tension for the same fiber orientations, respectively. The nonlinear deformations under off-axis tensile and compressive loading conditions exhibit significant strain-rate dependence. Similar features are observed in the fiber-orientation dependence of the off-axis flow stress levels under tension and compression and in the off-axis flow stress differential in tension and compression, regardless of the strain rate. A phenomenological theory of viscoplasticity is then developed which can describe the tension-compression asymmetry as well as the rate dependence, nonlinearity and fiber orientation dependence of the off-axis tensile and compressive behaviors of unidirectional composites in a unified manner. It is demonstrated by comparing with experimental results that the proposed viscoplastic constitutive model can be applied with reasonable accuracy to predict the different, nonlinear and rate-dependent behaviors of the unidirectional composite under off-axis tensile and compressive loading conditions.

• 한국안전학회지
• /
• 제9권4호
• /
• pp.29-41
• /
• 1994

High temperature tensiles tests, steady state creep tests, internal stress tests and creep rupture tests using Al 7075 alloy were performed over the temperature range of 9$0^{\circ}C$~50$0^{\circ}C$ and stress range of 0.64~17.2(kgf/$\textrm{mm}^2$) in order to investigate the creep behavior and predict creep rupture life From the apparent activation energy Qc and the applied stress exponent n measured, at the temperature range of 9$0^{\circ}C$~l2$0^{\circ}C$, the creep deformation seemed to be controlled by cross slip. On the other hand at the temperature of 20$0^{\circ}C$~23$0^{\circ}C$ the creep deformation seemed to be controlled by dislocation climb but at 47$0^{\circ}C$~50$0^{\circ}C$, by diffusion creep. And the rupture life(t$_{f}$) might be represented by anthermal process attributed to the difference of the applied stress dependence of Internal stress and the ratio of the Internal stress to the applied stress, the thermal activated process attributied to the temperature dependence of the internal stress. Also the ratio between stress dependence of primary creep rate and that of minimum creep rate was measured 0.46, the minimum creep rate is expected to be appromately obtained from master creep curve including the relationship primary creep rate and minumum creep rate. Finally the relationship new rupture parameter and logarithmic stress was represented with including the ratio between the dependence of primary creep rate and that of minimum creep rate, using the new rupture parameter the rupture life predition is exactly expected.d.

• 대한의료기공학회지
• /
• 제13권1호
• /
• pp.105-144
• /
• 2013

This study intended to provide fundamental data to take countermeasures against recurrent stress by analyzing the health-related quality of life and factors for recurrent stress of alcohol dependents. Structured questionnaire was prepared for patients who quitted drinking after they had been hospitalized for alcohol dependence to take medical treatment but suffered recurrence, and analysis on health-related quality of life and environmental factors with drinking risk was conducted. The quality of life was at a relatively satisfactory level, where pain was found at the highest level and general health condition was found at the lowest level. Environmental factors with drinking risk were found to be a moderate level, drinking for the reason of family and friends in terms of complications with other persons was found to be highest, and then job, self control, bad emotions, and social pressure on drinking were found in order. For health-related quality of life, the quality of life was found to be high in case of the only son, professional job, well-educated persons, and no history of hospitalization. Regarding factors for recurrent stress, stress was found to be high in case of the eldest son and being without religion, and the lower was the quality of life, the higher were recurrent stress and environmental factors with drinking risk. It was found that demographic factors including age, marriage, and job influenced the recurrence of alcohol dependence, and factors for recurrent stress, etc. also influenced recurrent alcohol dependence with drinking risks. Specially, the lower was the quality of life, the higher were factors for recurrent stress, and drinking risks, therefore measures to improve the quality of life are required to be taken to prevent alcohol dependence from recurrence.