• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.89-97
• /
• 2005

Recently, for the problem solution of demand and supply imbalance of fine aggregate due to the shortage of natural fine aggregate resource and the environment regulation on sea sand extraction in the construction field, the studies for the application of recycled fine aggregate using waste concrete are being progressed versatilely. On the other hand, the treatment of fly-ashes that of industrial by-product originated in the steam power plant is discussed by the continuous increasing of origination quantities. In the ease of using fly-ash, advantages are the improvement of workability, viscosity and long-time strength, and the reduction of hydration heat under the early ages, as the admixtures for concrete, but the studies for the application of fly-ash as recycled concrete admixtures are inadequacy. There fore, in this study, through investigating the properties of fresh, hardened and durability according to the replacement of recycled fine aggregate and fly-ash, it is intended to propose the fundamental data for structural application of recycled concrete using recycled fine aggregate and fly-ash. As the result of this study, they arc shown that the engineering properties and durability, in the case of replacement ratio 100% of recycled fine aggregate, arc similar to those of concrete using natural fine aggregate, so it is considered that recycled fine aggregate could be used as the fine aggregate for concrete. Also, the performances of recycled concrete are improved by replacing fly-ash.

• Clean Technology
• /
• v.20 no.3
• /
• pp.232-240
• /
• 2014

The significance of thermoplastic polyolefin polypropylene (PP) lies in its potential to replace polyvinyl chloride (PVC), the most widely used material for automobile interiors (door trim, dash board), which discharges harmful compounds in certain conditions. Another benefit of PP (0.855 amorphous - 0.946 crystalline $g/cm^3$) is its low density compared to that of PVC ($1.1-1.45g/cm^3$), which reduces vehicle weight. Market demand for eco-friendly water-based adhesive/coating material is rising significantly as a substitute for solvent-based adhesive/coating material which emits VOC and causes harmful working conditions. Under such context, in this study, a series of eco-friendly waterborne polyurethane-urea primer (a paint product that allows finishing paint to adhere much better than if it were used alone) for hydrophobic PP were prepared from different mix of DMPA content, NCO/OH molar ratio, various wt% of silicone diol and various soft segment content, among which DMPA of 21 mole %, NCO/OH molar ratio of 1.2, modified silicone diol of 5 wt% and soft segment content of 73 wt% led to good adhesion strength. Additionally, the incorporation of optimum content of additives (0.5 wt% dispersing agent, 0.5 wt% levelling agent, 1.5 wt% antifoaming agent, 3.0 wt% matting agent) into the optimum waterborne polyurethane-urea also enabled good stability, levelling, antifoaming and non-glossy.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.766-773
• /
• 2013

A transparent film was fabricated based on bacterial cellulose (BC), BC has excellent physical strength and stability at high temperature and it is an environmental friendly flexible material. In order to improve the conductivity, silver nanowire (AgNW) and/or graphene were introduced to the BC membrane. The aspect ratio of the AgNW synthesized in this study was 214, with a length of $15{\mu}m$ and width of 70 nm. The higher aspect ratio improved the conductivity by reducing the contact resistance. The thermal and electrical properties of 7 types of films prepared were investigated. Each film was fabricated with rectangular shape ($2mm{\times}2mm{\times}50{\mu}m$). The films were scored with a net shape by a knife, and filled with AgNW and graphene to bestow conductivity. The film filled with AgNW showed favorable electrical characteristics with a thickness of $350{\mu}m$, electron concentration of $1.53{\times}10^{19}$, electron mobility of $6.63{\times}10^5$, and resistivity of 0.28. The film filled with graphene had a thickness of $360{\mu}m$, electron concentration of $7.74{\times}10^{17}$, electron mobility of 0.17, and resistivity of 4.78. The transmittances at 550 nm were 98.1% and 80.9%, respectively. All the films were able to light LEDs bulbs although their brightness differed. A thermal stability test of the BC and PET films at $150{\pm}5^{\circ}C$ showed that the BC film was more stable, whereas the PET film was quickly banded. From these results, it was confirmed that there it is possible to fabricate new transparent conductivity films based on BC.

• Korean Journal of Poultry Science
• /
• v.34 no.1
• /
• pp.37-42
• /
• 2007

This study was conducted to investigate the effects of graded levels of a herbal recipe(Herb Mix $Gold^{(R)}$, Herb BIO Co.) supplemented to a commercial layer diet. The Herb Mix $Gold^{(R)}$ is an improved recipe of Herb $Mix^{(R)}$, fortified with Angelica gigas, Discorea japonica and Ligusticum jeholense. A total of 720 layers (Hy-Line Brown) of 45 wks old were assigned to one of six treatments; control, 0.2% Herb $Mix^{(R)}$, 0.1%, 0.2%, and 0.3% Herb Mix $Gold^{(R)}$, and 6 ppm Avilamycin. Each treatment had 6 replicates of 20 birds each housed in 2 birds cages. Birds were fed diets and water ad libitum for 5 weeks. Hen-day egg production was significantly (P<0.05) different among treatments. Herb Mix $Gold^{(R)}$ 0.2% treatment showed the highest egg production followed by Herb Mix $Gold^{(R)}$ 0.3%, Herb $Mix^{(R)}$ 0.2%, Herb Mix $Gold^{(R)}$ 0.1%, Avilamycin 6 ppm and the control. Hen-housed egg production, egg weight, soft and broken egg ration, feed intake, feed conversion ratio, shell strength, shell thickness, shell color index, Haugh unit and yolk color index were not significantly different among treatments. Nor was cfu of Cl. perfringens and E. coli and Lactobacilli in the small intestinal content significantly different among treatments. The number of white and red blood cells, hemoglobin, heterophil, lymphocyte, thus heterophil to lymphocyte ratio were not significantly modified. It was concluded that Herb Mix $Gold^{(R)}$ at the level of 0.2% in the layer diet improves laying performance.

• Korean Journal of Remote Sensing
• /
• v.36 no.5_3
• /
• pp.1109-1123
• /
• 2020

In South Korea with forest as a major land cover class (over 60% of the country), many wildfires occur every year. Wildfires weaken the shear strength of the soil, forming a layer of soil that is vulnerable to landslides. It is important to identify the severity of a wildfire as well as the burned area to sustainably manage the forest. Although satellite remote sensing has been widely used to map wildfire severity, it is often difficult to determine the severity using only the temporal change of satellite-derived indices such as Normalized Difference Vegetation Index (NDVI) and Normalized Burn Ratio (NBR). In this study, we proposed an approach for determining wildfire severity based on machine learning through the synergistic use of Sentinel-1A Synthetic Aperture Radar-C data and Sentinel-2A Multi Spectral Instrument data. Three wildfire cases-Samcheok in May 2017, Gangreung·Donghae in April 2019, and Gosung·Sokcho in April 2019-were used for developing wildfire severity mapping models with three machine learning algorithms (i.e., Random Forest, Logistic Regression, and Support Vector Machine). The results showed that the random forest model yielded the best performance, resulting in an overall accuracy of 82.3%. The cross-site validation to examine the spatiotemporal transferability of the machine learning models showed that the models were highly sensitive to temporal differences between the training and validation sites, especially in the early growing season. This implies that a more robust model with high spatiotemporal transferability can be developed when more wildfire cases with different seasons and areas are added in the future.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.2
• /
• pp.62-69
• /
• 2003

The aim of research is the evaluation of the $Cr^{6+}$ emission features of the liquid injection through emission experiments in varying conditions, based on a field-mixing ratio. The results showed that the content of $Cr^{6+}$ content in cement measured had an Ordinary Potland Cement (OPC) of 25.3 mg/kg, which constitute the largest portion among the other materials. Likewise, the emission experiment of homo-gel and sand-gel generally satisfied the standard of KSLT (Korea Standard Leaching Test) in waste of 1.5 mg/L, but in case of the standard of KSLT in soil the emission of OPC $Cr^{6+}$ of 4.85 mg/kg. These conditions is a little exceeded the criteria in the ‘Ga’ area in terms of Korea Soil Environmental Preservation Law. In addition, results generated by the mock-up injection facilities revealed that $Cr^{6+}$ emission increased as Water/Cement and injection pressure increased. At injection pressure higher than 4 kg/㎤, $Cr^{6+}$ emission exceeded the water preservation standard of 0.5 mg/L. Similarly, a pattern experiment of C $r^{6+}$ emission according to pH was conducted, in order to evaluate the $Cr^{6+}$ emission features of grout materials in leachate below pH 5 such as pH 4 acid rain or landfill. Results show that $Cr^{6+}$ emission dramatically increased in high acidic or basic state. It indicates that $Cr^{6+}$ emission will probably increase in an environment where grout materials are injected. On the other hand, concentration of leachate was determined in areas where grout materials are used. The results show that the concentration of emission in an ultra purity condition does not manifest intensity, and is affected in the OPC>MC>SC order. It means that the pollutants or $Cr^{6+}$ emission increases with decreasing concentration. As such, $Cr^{6+}$ emission will probably exceed the countermeasure criteria according to the types of gout materials. Similarly, high pressure or injection will cause increased $Cr^{6+}$ emission. Therefore, the selection of materials or mixing ratio should be considered in general as well as according to specific industries, based on the strength and pH of $Cr^{6+}$ emission.

• Journal of Korean Society of Forest Science
• /
• v.89 no.2
• /
• pp.275-284
• /
• 2000

This study was carried out to analyze the mechanical properties of soil and the slope stability on the fill slope of forest road constructed in the regions which consist of igneous and metamorphic rock area. The results were summarized as follows. 1) Soil type by Unified Soil Classification System(USCS) was classified as SW in soil slope, GP in weathered rock slope, GP in soft rock slope for both types of parent rock, but gravelly soil slopes in igneous and metamorphic rock area were classified as SP and GW, respectively. 2) Dry unit weight was $1.34g/cm^2{\sim}1.59g/cm^2$, specific gravity 0.57~0.61, and void ratio 0.66~0.93 in the case of igneous rock area, a dry unit weight was $1.35g/cm^2{\sim}1.51g/cm^2$, specific gravity 2.67~2.77, and void ratio 0.78~1.01 in the case of metamorphic rock area. 3) The strength parameters such as internal friction angle(${\phi}$) and cohesion(c) were selected and tested for slope stability analysis. ${\phi}$ and c of soil in igneous rock area were within the range of $29.51^{\circ}{\sim}41.82^{\circ}$ and $0.03kg/cm^2{\sim}0.38kg/cm^2$, respectively, and $21.43^{\circ}{\sim}41.43^{\circ}$ and $0.05kg/cm^2{\sim}0.44kg/cm^2$ in metamorphic rock area, respectively. 4) Result of the slope stability analysis of forest road showed that, in the weathered rock slope of igneous rock and the weathered rock and soil slope of metamorphic rock area, the possibility of slope failure was high as safety factor was below 1.0.

• Food Engineering Progress
• /
• v.14 no.3
• /
• pp.193-201
• /
• 2010

The aim of this study was to analyse the quality of Yukwa puffed by using a vacuum puffing machine and compare to deep-fried Yukwa. The effect of vacuum puffing condition including heating temperature(100-${160^{\circ}C}$), preheating time(0-8 min) and vacuum puffing time(5-20 min) on physical and microstructure characteristics of the Yukwa was investigated. Vacuum puffed Yukwa at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 10 min puffing time had highest value in volumetric expansion ratio(10.04) and lowest value in bulk density(0.15 g/$cm^{3}$). The breaking strength showed the lowest value of 140 g/$cm^{3}$ in vacuum puffing Yukwa at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 15 min puffing time. The Yukwa puffed with the vacuum puffing machine at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 15 min puffing time had the higher value of bulk density and the lower value of volumetric expansion ratio than those of deep-fried Yukwa. Increasing preheating time and vacuum puffing time caused an increase in white and an decrease in yellowness. The vacuum-puffed Yukwa exhibited smaller and uniform cell structure, while deep-fried Yukwa exhibited apparently in larger pores inside and smaller pores near the surface layer. The optimum condition of vacuum puffing machine for the production of vacuum-puffing Yukwa was ${120^{\circ}C}$ heating temperature, 4 min preheating time and 5 min puffing time.

• Korean Journal of Poultry Science
• /
• v.49 no.4
• /
• pp.181-188
• /
• 2022

This study was conducted to investigate the effects of the metabolic energy levels of Korean native chicken breeder diets on laying performance, egg quality, fertility and hatchability. On the basis of dietary metabolic energy values (2,800, 2,700, and 2,650 kcal/kg), 168 twenty-week-old 'Woorimatdag' breeders (maternal line) were divided into three treatment groups (four replications per treatment with each replicate containing 14 birds) and reared until 32 weeks of age. We found that the body weight of hens increased with age, although there were no significant differences among treatments with respect to body weight or egg weight. Egg production ratio at 20-24 and 24-28 weeks of age tended to be low in birds fed the 2,700 and 2,650 kcal/kg diets, although the differences among treatments were none significant. Feed intakes was significantly decreased as the metabolic energy level reduced (P<0.05). There were no significant differences among treatments with respect to feed conversion ratio or the strength and thickness of eggshell. Similarly, we detected no significant differences among the three metabolic energy levels with regards to fertility, hatchability, or chick weight. In conclusion, our findings indicate that during the initial phase of laying, the metabolic energy level of 'Woorimatdag' breeder diets could be lowered to 2,700 kcal/kg without significantly influencing the laying performance of breeders or egg quality, fertility and hatchability, and chick weight.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.101-114
• /
• 2008

Pressurized grouting is a common technique in geotechnical engineering applications to increase the stiffness and strength of the ground mass and to fill boreholes or void space in a tunnel lining and so on. Recently, the pressurized grouting has been applied to a soil-nailing system which is widely used to improve slope stability. Because interaction between pressurized grouting paste and adjacent ground mass is complicated and difficult to analyze, the soil-nailing design has been empirically performed in most geotechnical applications. The purpose of this study is to analyze the ground behavior induced by pressurized grouting paste with the aid of laboratory model tests. The laboratory tests are carried out for four kinds of granitic residual soils. When injecting pressure is applied to grout, the pressure measured in the adjacent ground initially increases for a while, which behaves in the way of the membrane model. With the lapse of time, the pressure in the adjacent ground decreases down to a value of residual stress because a portion of water in the grouting paste seeps into the adjacent ground. The seepage can be indicated by the fact that the ratio of water/cement in the grouting paste has decreased from a initial value of 50% to around 30% during the test. The reduction of the W/C ratio should cause to harden the grouting paste and increase the stiffness of it, which restricts the rebound of out-moved ground into the original position, and thus increase the in-situ stress by approximately 20% of the injecting pressures. The measured radial deformation of the ground under pressure is in good agreement with the expansion of a cylindrical cavity estimated by the cavity expansion theory. In-situ test revealed that the pullout resistance of a soil nailing with pressurized grouting is about 36% larger than that with regular grouting, caused by grout radius increase, residual stress effect, and/or roughness increase.