• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.239-247
• /
• 2005

In this study, an experimental study on the sorption properties of uranium(VI) onto bentonite colloids generated from a domestic calcium bentonite (called as Gyeongju bentonite). Gyeongju bentonite has been considered as a potential candidate buffer material in the Korean disposal concept for high-level radioactive wastes. The size and concentration of the bentonite colloids used in the sorption experiment were measured by a filtration method. The result showed that the concentration of the synthesized bentonite colloid suspension was 5100ppm and the size of the most of bentonite colloids(over $98\%$) was in the range of 200-450nm in diameter. The amount of uranium lost by the sorption onto bottle walls, by precipitation, and by ultrafiltration or colloid formation was analyzed by carrying out some blank tests. The loss of uranium by the ultrafiltration was significant in the lower ionic strength(i.e., in the case of 0.001M $NaClO_4$) due to the cationic sorption effect onto the ultrafilter by a surface charge reversion. The distribution coefficient (or pseudo-colloid formation constant) for the sorption of uranium(VI) onto bentonite colloids was $10^4^{\sim}10^6$ mL/g depending upon pH and the distribution coefficient was highest in the neutral pH around 6.5.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.4
• /
• pp.207-218
• /
• 2013

This study is based on a series of numerical modeling experiments to understand the circulation and its change in the Chunsu Bay (CSB), Yellow Sea of Korea. A skill analysis was performed for the tidal height and tidal current of the observation data using the amplitude and phase of the 4 major tidal constituents respectively for verification of modeling experimental results. As a result, most of the skill score was seen to be over 90%, so numerical model experiment results can be said to be in good agreement with the observed tidal height and tidal current. Tidal wave proceeded from the entrance of the CSB towards inside, and the tidal range gradually increased to the north. It took about 10 to 30 minutes for the tidal wave to reach to northern end. The tidal wave showed a characteristic to rotate counter-clockwise in the southern part. The tidal current flowed to the north-south direction along the bottom topography; the angle of the major axis appeared alongside the isobath. It showed the characteristics of reversing tidal current with the minor axis less than 10% of the major axis. The strength of the tidal residual current that is influenced by geographical factors including bathymetry and coastline showed the range of 1~30 cm/sec, greater in the south channel and smaller in northern Bay. Two pairs of cyclonic/anti-cyclonic eddies around Jukdo and 3~4 pairs of strong eddies at the southern part of CSB in hundreds of m to a few km size by relative vorticity derived from the tidal residual current.

• Journal of Animal Science and Technology
• /
• v.46 no.6
• /
• pp.975-980
• /
• 2004

An experiment was conducted to determine the effects of dietary supplementation of the yeast Rhodotorula glutinis(Glutinicus) on the performance and egg quality of layers. A total of 360 ISA Brown layers at 72 weeks old were assigned to one of the following 6 diets: control, 25 ppm$\beta$-carotene, 0.50%0, 1%0, 2% and 4% Glutinicus supplemented diets. Each treatment was replicated three times with 20 birds housed in 2 bird cage units. Glutinicus supplementation at the level of 0.5% significantly(p < 0.05) improved egg production and FCR Soft and broken egg production rate decreased as the level of Glutinicus supplementation increased. Eggshell strength was highest in 4 % Glutinicus supplementation. Egg yolk color increased linearly as the level of Glutinicus supplementation increased up to 2% of the diet. It was concluded that Glutinicus supplementation at the level of 0.5% can be recommended for the improvement of egg production while 2.0% can be recommended for egg yolk pigmentation.

• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.471-481
• /
• 2007

The Landslide in natural slope is occurred mostly by a heavy rain of the summer. This landslide is influenced in soil property of the surface than the rock mass. Soils in natural slope are created by weathering phenomena of the bedrock. These soils differed to the geological conditions such as sedimentary rock, metamorphic rock and volcanic rock. Therefore, estimation of landslide in natural slope is the most important analysis of the bedrock distributions and soil characteristics. This study analyzed the soil property to the natural slopes of Busan area where is distributed to volcanic rock, granite and sedimentary rock. Soil sample conducted various soil tests for estimate the soil physical property and soil engineering characteristics, and analysis of the correlation of geological conditions. In the experiment result, soils were mainly classified by a clayey sand. It is also established that $1.07{\sim}1.99kg/cm^3$ for wet density, $28.2{\sim}39.6^{\circ}$ for angle of shearing resistance, and $8.10{\times}10^{-5}{\sim}8.38{\times}10^{-2}cm/sec$ for coefficient of permeability. From the physical parameter, the soils are estimated to the permeable ground with good shear strength, and soil properties are showed a differential tendency for each geological condition.

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.42-49
• /
• 2017

To replace phthalate plasticizer for PVC, acetylated monoglyceride (AMG) plasticizers were prepared from plant oil and their plasticization effects were also investigated. Transesterification of coconut oil by glycerol followed by acetylation with acetic anhydride gave AMG-CoCo (Coco : Coconut Oil). In addition, AMG-GMO (GMO : Glycerol monooleate) and AMG-GMO-Epoxy were synthesized by acetylation and epoxidation with glycerol monooleate. It was found that the thermal stability of AMG plasticizers increased in the following order: AMG-GMO-Epoxy > AMG-GMO > AMG-CoCo and all three plasticizers were thermally more stable than those of common petroleum-based plasticizer DOP (Dioctyl phthalate). The tensile strain values of the PVC containing AMG compounds were ca. 770~810%, while tensile strength values were ca. 19~22 MPa, which were higher than those of PVC containing DOP. DMA (Dynamic Mechanical Analysis) results showed that the miscibility of AMG-GMO-Epoxy in PVC was excellent and the $T_g$ of PVC containing AMG-GMO-Epoxy at 50 phr decreased down to $24^{\circ}C$. Finally, the leaching experiment result showed that the weight loss values of PVC containing AMG-GMO and AMG-GMO-Epoxy at 50 phr were as low as 2 and 1%, respectively, indicating that they have high water migration resistance. The above findings suggested that AMG-GMO-Epoxy could be one of plant oil-based PVC plasticizers to replace DOP.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.49-58
• /
• 2017

The phenomena that we experience in everyday life such as snow, rain, wind, and temperature are referred to as weather, and the average state of atmospheric phenomena that occur over a long period of time in a specific region is referred to as climate. In addition, significant variation of climate compared to the average state is referred to as climate change. Concrete structures can have various problems when exposed to elements. Among the problems, the freeze-thaw problem due to extreme climatic factors such as heavy rain and snowfall has become a particularly significant issue recently. The concrete that has been subjected to repeated freeze-thaw rather than too high or low temperature shows serious degradation of durability, and the performance of structures with degraded performance is difficult to recover. Therefore, in this study, concrete durability performance with respect to freeze-thaw from curing conditions change due to wind speed and sunshine exposure time. Concrete freeze-thaw experiment are performed. using wind speed and sunlight exposure time. Also, performance based evaluation through the satisfaction curve based on the freeze-thaw test results are performed.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.10
• /
• pp.17-29
• /
• 2016

A debris flow analysis model has been developed to simulate the erosion and entrainment of soil layer. Special attention is given to the model which represents strength softening behaviour of soil layer due to velocity of deformation. The 3D FE analysis by Coupled Eulerian-Lagrangian (CEL) model is conducted to simulate the debris flow. The model is validated using published data on laboratory experiment (Mangeny et al., 2010). It has been definitely shown that proposed model is in good agreement with the results of laboratory data. Futhermore, the FE analysis is conducted to ensure capability of simulating the real scale debris flow. The result of Ramian watershed, Korea shows that the debris flow has increased the volume and speed and it is in good agreement with field investigation. Based on this, it is confirmed that proposed model shows good agreement of the behavior of the actual and analytical debris flow.

• Journal of the Korean Ceramic Society
• /
• v.41 no.7
• /
• pp.518-527
• /
• 2004

In this study, SiC whiskers were grown in porous alumina substrate in order to enhance the filtering efficiency, performance, and durability by controlling pore morphology. This experiment was performed by Chemical Vapor Infiltration (CVI) in order to obtain the whiskers on the inside of pores as well as on the surface of porous the A1$_2$O$_3$ substrate. The deposition behavior was changed remarkably with the deposition position, temperature, and input gas ratio. First, the mean diameter of whisker was decreased as the position of observation moved into the inside of substrate due to the reactant gas depletion effect'. Second, the deposition temperature caused the changes of the deposition type such as debris, whiskers and films and the change in morphology affect the various properties. When SiC films were deposited. the gas permeability and the specific surface area decreased. However, the whisker showed the opposite result. The whiskers increase not only the specific surface area and minimizing pressure drop but also mechanical strength. Therefore it is expected that the porous alumina body which deposited the SiC whisker is the promising material for the filter trapping the particles.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.35-47
• /
• 1996

A surface panel method treating a boundary-value problem of the Dirichlet type is presented to design a three dimensional body with free surface corresponding to a prescribed pressure distribution. An integral equation is derived from Green's theorem, giving a relation between total potential of known strength and the unknown local flux. Upon discretization, a system of linear simultaneous equations is formed including free surface boundary condition and is solved for an assumed geometry. The pseudo local flux, present due to the incorrect positioning of the assumed geometry, plays a role f the geometry corrector, with which the new geometry is computed for the next iteration. Sample designs for submerged spheroids and Wigley hull and carried out to demonstrate the stable convergence, the effectiveness and the robustness of the method. For the calculation of the wave resistance, normal dipoles and Rankine sources are distributed on the body surface and Rankine sources on the free surface. The free surface boundary condition is linearized with respect to the oncoming flow. Four-points upwind finite difference scheme is used to compute the free surface boundary condition. A hyperboloidal panel is adopted to represent the hull surface, which can compensate the defects of the low-order panel method. The design of a 5500TEU container carrier is performed with respect to reduction of the wave resistance. To reduce the wave resistance, calculated pressure on the hull surface is modified to have the lower fluctuation, and is applied as a Dirichlet type dynamic boundary condition on the hull surface. The designed hull form is verified to have the lower wave resistance than the initial one not only by computation but by experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1438-1443
• /
• 2001

The significance of the casting/forging process for reducing the production cost of large components is being noted in these days. This casting/forging process is a method of forging a workpiece preformed by casting into the final shape. In this study, the casting/forging process has been applied in manufacturing a large aluminum flange in order to reduce press capacity and material cost. Firstly, a hot compression test was performed with cast cylindrical billets in order to determine the optimum forging condition of the aluminum flange. The optimum range of forging temperature of Al 5083 was from 420$\^{C}$ to 450$\^{C}$. The suitable strain rate was 1.5 sec(sup)-1. The deformation amount of a preform of a preform in a forging process is a key role in the mechanical properties of casting/forging products. In order to find the change of mechanical properties according to effective stain of cast aluminum billets, a hot upsetting test were performed with rectangular blocks and then a uniaxial tensile test was performed with specimens cut from the upsetted billets. The tensile strength and the elongation of cast/upsetted aluminum billets were increased largely until the effective strain was 0.7. FE analysis was performed to determine the configurations of case preform and die for an aluminum flange. In the FE analysis, the forging load-limit was fixed 1500ton for low equipment cost. The cast preform was designed so that the effective stain around the neck of a flange exceeded 0.7. From the result of FE analysis, optimal configurations of the cast preform and the die were designed for a large flange. The filling and solidification analysis for a sound cast-preform was carried out with MAGMA soft. In the forging experiment for an aluminum flange, it was confirmed that the optimal configuration of the cast preform predicted by FE analysis was very useful. The cast/forged products using designed preform were made perfectly without any defects.