• 대한기계학회논문집B
• /
• 제22권8호
• /
• pp.1173-1182
• /
• 1998

A throughflow analysis program for axial flow turbines is constructed, which can handle not only the two-dimensional multi-streamline (streamline curvature) method but also the one-dimensional mean line method. Calculations are performed for single stage and multi-stage axial flowturbines. For a wide operating range, the performance and flow field calculated by the present streamline curvature method are close enough to the test data. It is also revealed for the single stage turbine that the present analysis leads to far better correspondence with the experiment than other researchers" throughflow analyses. A special focus is put on the comparison of the results between the streamline curvature analysis and the mean line analysis. It is found that the mean line analysis can not predict the performance for highly off-designed conditions as accurately as the streamline curvature method, which shows the importance of considering the spanwise variation of loss and flow.

• 대한기계학회논문집B
• /
• 제22권11호
• /
• pp.1591-1602
• /
• 1998

Simple spanwise distribution models of deviation angle and pressure loss coefficient due to the tip leakage flow are formulated for use in association with the streamline curvature method as a flow analysis. Combining these new models with the previous deviation and loss models due to secondary flow, a robust streamline curvature method is established for flow analysis of single-stage, subsonic axial turbines with wide ranges of turning angle, aspect ratio and blading type. At the exit from rotor rows, the flow variables are mixed radially according to a spanwise transport equation. The proposed streamline curvature method is tested against a forced vortex type turbine as well as a free vortex type one. The results show that the spanwise variations of flow angle, axial velocity and loss coefficients at rotor exit are predicted with good accuracy, being comparable to a steady three-dimensional Navier-Stokes analysis. This simple and fast flow analysis is found to be very useful for the turbine design at the initial design phase.

• 한국추진공학회지
• /
• 제22권5호
• /
• pp.1-12
• /
• 2018

유선곡률해석법은 다단 축류 터빈의 설계과정에서 필수적으로 이용되며, 실제 작동환경에서 발생하는 손실을 설계 단계에서 미리 반영할 수 있다는 장점이 있다. 하지만 이와 관련한 국내 독자 연구가 부족한 실정이다. 본 연구에서는 다단 축류 터빈에서의 누설 유동에 따른 성능해석을 위해 유선곡률해석법과 유동 혼합에 따른 손실 예측 모델을 적용하였다. 국내 운전 중인 86 MW급 발전용 가스터빈의 5단 축류터빈에 대해 본 연구에서 제안한 방법을 적용하여 성능해석을 수행하였다. 계산된 결과는 3차원 전산해석 결과와 비교하였으며, 유선곡률해석법이 가지는 장점과 한계에 대해 기술하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제10회 학술강연회논문집
• /
• pp.13-13
• /
• 1998

A simple model of the tip leakage flow models of the rotor downstream flow is developed, based on Lakshminarayana's theoretical concept on the tip clearance flow and the experimental data published in open literature. And new spanwise distribution models of deviation angle and pressure loss coefficient due to the tip leakage flow are formulated for use in association with the streamline curvature method as a through flow analysis. Combining these new models and previous deviation and loss models due to secondary flow, a robust streamline curvature method is established for flow analysis of single-stage, subsonic axial turbines with wide ranges of turning angle, aspect ratio and blading type. At the exit from rotor rows, the flow variables are mixed radially according to a spanwise transport equation. The proposed streamline curvature method is tested against a forced vortex type turbine as well as a free vortex type one. The results show that the spanwise variations of flow angle, axial velocity and loss coefficients at rotor exit are predicted with good accuracy, being comparable to a steady three-dimensional Navier-Stokes analysis. This simple and fast flow analysis is found to be very useful for the turbine design at the initial design phase.

• 설비공학논문집
• /
• 제1권1호
• /
• pp.87-96
• /
• 1989

Flows through impellers of centrifugal compressors are calculated by a streamline curvature method. A method for the exit boundary condition is suggested in the present paper. Flow angles are assumed to be deviated from the blade angle parabolically. The maximum deviation is adjusted for the whole angular momentum to balance with the empirically estimated value by using Stanitz' slip-factor. The present method is verified to reasonably simulate flows through the impeller, when the 3-dimensionality of the flow is not strong. It is also shown that the method can be applied for the design of the splitter in the impeller.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.70-77
• /
• 1986

본 논문에서는 재순환 영역이 존재하는 축대칭 난류 확산화염 구조예측의 전 단계로서, 이미 발표된 바있는 필자의 실험 데이터를 바탕으로 하여 등온유동에 서의 난류모델을 검토한다. 유선의 곡률이 큰 유동에 2방정식 모델을 적용함은 큰 결점을 보완한 수정-2방정식모델을 채택하여 실험결과와 비교, 검토하여 모델의 타당성을 조사하였다.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.224-232
• /
• 2000

Four turbulent $k-{\varepsilon}$ models (i.e., standard model, modified models with streamline curvature modification and/or preferential dissipation modification) are applied in order to analyze the turbulent flow of wall-attaching offset jet. For numerical convergence, this paper develops a method of slowly increasing the convective effect induced by skew-velocity in skew-upwind scheme (hereafter called Partial Skewupwind Scheme). Even though the method was simple, it was efficient in view of convergent speed, computer memory storage, programming, etc. The numerical results of all models show good prediction in first order calculations (i.e., reattachment length, mean velocity, pressure), while they show some deviations in ·second order (i.e., kinetic energy and its dissipation rate). Like the previous results obtained by upwind scheme, the streamline curvature modification results in better prediction, while the preferential dissipation modification does not.

• 동력기계공학회지
• /
• 제3권3호
• /
• pp.54-59
• /
• 1999

The purpose of the present study was to develop the numerical method for predicting the on-design and off-design performance of multistage axial-flow compressors. The aerodynamic properties in blade rows were analyzed by incorporating the streamline curvature method as a quasi 3D analysis with the imperical modeling of exit flow angle and loss coefficients. The present calculation procedure has been tested by applying to 5-stage compressors and good agreement with experiments has been found. The detail analysis of aerodynamic performances has been done on the compression part of the bench-scaled gas turbine engines. The predicted performance map at the variable speedline and flow rates could be used as a guide of the engine operation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권2호
• /
• pp.216-225
• /
• 1999

Four turbulent $k-{varepsilon}$models(i.e standard model modified models with streamline curvature modification and/or preferential dissipation modification) are applied in order to analyze the tur-bulent flow of wall-attaching offset jet. The upwind numerical scheme was adopted in the present analyses. The streamline curvature modification results in slightly better prediction while the preferential dissipation modification does not. The obtained analytic results will be used as refer-ences for further study regarding Reynolds stress model. In addition this paper introduced a method of increasing nozzle outlet velocity gradually for numercal convergence. Even though the method was simple it was efficient in view of convergent speed CPU running time computer memory storage programming etc.

• 한국항공우주학회지
• /
• 제36권7호
• /
• pp.621-627
• /
• 2008

풍동에서 측정된 공력자료에는 풍동벽면의 영향으로 인하여 불가항력적인 오차가 포함되어 있다. 벽면영향이 없는 공력자료를 얻기 위해서는 이러한 원하지 않는 벽면효과를 제거 하여야 한다. 유선곡률 효과는 풍동벽면의 영향으로 유선의 곡률이 자유 흐름의 것과 다르기 때문에 발생한다. 고정익 항공기에 사용되고 있는 전통적인 유선곡률 효과를 보정방법인 Glauert의 보정방법은 회전익 항공기에 적용이 적절하지 않다. 본 논문에서는 로터에 적절한 후류모델을 사용하는 Heyson의 보정방법을 사용하여 로터축 기울어짐 각과 동압을 보정하였다. Heyson 보정방법의 결과를 Glauert 보정방법의 결과와 비교하였다.