• 오토저널
• /
• 제3권3호
• /
• pp.39-48
• /
• 1981

The combustion phenomena of the stratified charged model combustion chamber under the initial conditions of the room temperature and the atmospheric pressure were investigated by using pressure record and high speed Schliern motion picture in comparison with that of the uniformly charged case. The results show that the total burning time is strongly dependent on the turbulent spouting flame jet speed which promotes the combustion process inside the chamber, and the pressure rise-up of stratified charged combustion is rather faster and higher than that of uniformly charged combustion, which can be resulted in the energy saving.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.704-709
• /
• 2000

Laminar burning velocities of propane- and iso-octane-air mixtures have been numerically modelled over a wide range of equivalence ratio, pressure and temperature. These correlations are applicable to the modelling of stratified charged combustion like that of lean bum and GDI engine combustion. The numerical models are based on the results calculated by PREMIX code with Sloane's detailed chemical reaction mechanism for propane and FlameMaster code with Peters' for iso-octane. Laminar burning velocity for two fuels showed a pressure and temperature dependence in the following form, in the range of $0.1{\sim}4MPa$, and $300{\sim}1000K$, respectively. $S_L={\alpha}\;{\exp}[-\xi({\phi}-{\phi}_m)^2-{\exp}\{-{\xi}({\phi}-{\phi}_m)\}-{\xi}({\phi}-{\phi}_m)]$ where ${\phi}_m=1.07$, and both of ${\alpha}$ and ${\xi}$ are functions of pressure and temperature. Compared with the results of the existing models, those of the present one showed the good agreement of the recent experiment data, especially in the range of lean and rich sides. Judging from the calculated results of the stratified charged combustion by using STAR-CD, the above modelling prove to be more suitable than the other ones.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.50-55
• /
• 2001

To simulate the combustion process under stratified charged conditions, like GDI engines, the new combustion model is proposed, which is based on Welter's FAE model and Peters' PDF model for considering primary reactions. In addition to these models, the new laminar burning velocity correlation and diffusion flame model are also included in the proposed model. The former can be applicable to much wider range of equivalence ratio, pressure and temperature than the others, such as Keck's and Guilder's models, and the latter has been derived from water-gas shift reaction and hydrogen oxidation, by which the secondary reactions can be considered after primary reactions. 3-D computation has been performed by using STAR-CD v3.05 in the simple cylindrical geometry under stratified charged condition. Judging from the calculated results, the present model proves to be reasonable to simulate the characteristics of flame propagation and concentrations of products in burned regions.

• 한국수소및신에너지학회논문집
• /
• 제22권6호
• /
• pp.895-904
• /
• 2011

Stratified charge has been thought as one of the ways to avoid a sharp pressure rise on HCCI combustion. The purpose of this study is to evaluate the potential of stratified charge for reducing PRR on HCCI combustion. The pre-mixture with thermal, mixing and EGR stratifications is charged in Rapid Compression Machine. After that, the pre-mixture is compressed and in that process, in-cylinder gas pressure and temperature are analyzed. Additionally numerical calculation with multi-zones modeling is run to know the potential of stratified charge for reducing PRR.

• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.121-126
• /
• 2006

A gasoline-fueled stratified charge compression ignition (SCCI) engine with both direct fuel injection and intake temperature and compression ratio was examined. The fuel was injected directly by using the high temperature resulting from heating intake port. With this injection strategy, the SCCI combustion region was expanded dramatically without any increase in NOx emissions which were seen in the case of compression stroke injection. Injection timing during the intake temperature was found to be an important parameter that affects the SCCI region width. The effect of mixture stratification and the effect of fuel reformation can be utilized to reduce the required intake temperature for suitable SCCI combustion under each set of engine speed and compression ratio conditions.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1303-1310
• /
• 2001

In order to be applicable to the combustion modelling of stratified charged combustion like that of - lean burn and GDI engine, the correlations of laminar burring velocities fur several hydrocarbon fuels and methanol are needed over a wide range of equivalence ratio, pressure and temperature. In this study, these correlations are modeled in the 1311owing form based on the experimental and Muller\`s modeling results for several fuels, where $\alpha$, ξ, and ξ are functions of pressure and temperature, $S_{L}$ =$\alpha$ exp[-ξ($\Phi$-$\Phi$$_{m}$)$^{2}$ -exp {-ζ($\Phi$-$\Phi$$_{m}$)}-ζ($\Phi$-$\Phi$$_{m}$)]. By using the results calculated by PREMIX code with Sloane\`s detailed chemical reaction mechanism for propane, it is verified that the coefficients of the abode modeling can be determined by considering laminar burning velocity data only in a range of equivalence ratio less than $\Phi$$_{m}$. Therefore, Muller\`s modeling results can be adopted leer modeling of the pressure and temperature dependency. Compared with the results of the existing Keck'and Gulder's models, those of the present one showed the good agreement of the recent experimental data, especially in the range of lean and rich sides.s.des.s.