• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.23-32
• /
• 2010

This study was especially conducted to find out the characteristics of the lightweight air-mixed soil (slurry density 10 kN/$m^3$) containing silt related to water. Compression strength, permeability, and capillary height of the lightweight air-mixed soil were studied, and also to support these studies, the structure of that soil was analyzed in detail. Air bubbles of various sizes are inside the lightweight air-mixed soil, and its distribution in a location is almost constant. A numerous tiny pores are inside the air bubbles so that the lightweight air-mixed soil can be saturated with water. Porosity is also estimated through the image analysis. Peak strength of the lightweight air-mixed soil is not dependent on water, but behavior of stress-strain is affected by the water. Permeability is about $4.857{\times}10^{-6}cm/sec$, which is a little bit higher than the clay's permeability. Capillary rise occurs rapidly at the beginning of the test until the lapse of 100 minutes and then its increase rate becomes slow. The capillary rise causes the increase of the density of the lightweight air-mixed soil, and thus it is required to pay attention to this phenomenon during structure design and maintenance of the lightweight air-mixed soil.

• Steel and Composite Structures
• /
• v.46 no.1
• /
• pp.53-73
• /
• 2023

Man-made structure materials like concrete usually contain inclusions. These inclusions affect the mechanical properties of concrete. In this investigation, the influence of inclusion length and inclination angle on three-dimensional failure mechanism of concrete under uniaxial compression were performed using experimental test and numerical simulation. Approach of acoustic emission were jointly used to analyze the damage and fracture process. Besides, by combining the stress-strain behavior, quantitative determination of the thresholds of crack stress were done. concrete specimens with dimensions of 120 mm × 150 mm × 100 mm were provided. One and two holes filled by gypsum are incorporated in concrete samples. To build the inclusion, firstly cylinder steel tube was pre-inserting into the concrete and removing them after the initial hardening of the specimen. Secondly, the gypsum was poured into the holes. Tensile strengths of concrete and gypsum were 2.45 MPa and 1.5 MPa, respectively. The angle bertween inclusions and axial loadind ary from 0 to 90 with increases of 30. The length of inclusion vary from 25 mm to 100 mm with increases of 25 mm. Diameter of the hole was 20 mm. Entirely 20 various models were examined under uniaxial test. Simultaneous with experimental tests, numerical simulation (Particle flow code in two dimension) were carried out on the numerical models containing the inclusions. The numerical model were calibrated firstly by experimental outputs and then failure behavior of models containing inclusions have been investigated. The angle bertween inclusions and axial loadind vary from 0 to 90 with increases of 15. The length of inclusion vary from 25 mm to 100 mm with increases of 25 mm. Entirely 32 various models were examined under uniaxial test. Loading rate was 0.05 mm/sec. The results indicated that when inclusion has occupied 100% of sample thickness, two tensile cracks originated from boundaries of sample and spread parallel to the loading direction until being integrated together. When inclusion has occupied 75% of sample thickness, four tensile cracks originated from boundaries of sample and spread parallel to the loading direction until being integrated together. When inclusions have occupied 50% and 25% of sample thickness, four tensile cracks originated from boundaries of sample and spread parallel to the loading direction until being integrated together. Also the inclusion was failed by one tensile crack. The compressive strength of samples decease with the decreases of the inclusions length, and inclusion angle had some effects on that. Failure of concrete is mostly due to the tensile crack. The behavior of crack, was affected by the inclusion length and inclusion number.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6B
• /
• pp.695-701
• /
• 2006

A toluene-degrading bacterial strain was isolated from a mixed culture that was maintained using toluene as a sole carbon and energy source. The isolated bacterium was classified as Pseudomonas sp. TBD4 based on the close relationship to bacteria belonging to this genus. A bottle study to determine biodegradation rates of individual aromatic compounds showed that the biodegradation was faster in the order of toluene, benzene, styrene, and p-xylene. However, when various mixtures were subjected to TDB4, styrene was degraded at the highest rate, indicating that both toluene and p-xylene could stimulate the degradation of other substrates whereas styrene played as an inhibitor. In addition, the mixed culture and TDB4 were inoculated to the bioactive foam reactor (BFR), and the reactor performance and the corresponding change of microbial community were monitored using the fluorescent in situ hybridization (FISH) method. When an inlet concentration of the VOC mixture increased to greater than 250 ppm, the overall removal efficiency dropped significantly. The FISH measurement demonstrated that the ratio of TDB4 to the total bacteria also decreased to less than 20% along with the decline in removal efficiency in the BFR. As a result, the periodic addition of the pre-grown TDB4 might have been beneficial to achieve a stable performance in the BFR operated over an extended period.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.208-215
• /
• 1999

The creep behavior of a rapidly solidified and consolidated Al-9.45wt%Fe-4.45wt%Cr alloy were investigated in the stress range 40 to 115 MPa and temperature range 300(0.53Tm) to 441$^{\circ}C$(0.66Tm). It is of use to available aerospace and automobile industries for the improved performance of materials used at high temperature. Because Al alloys with improved creep resistance offer the potential for lower weight and reduced costs in aerospace and automobile components (e.g., structural members and engine parts) through the replacement of heavier and more costly materials, the safety in use at high temperature is good. The alloy is characterized by high stress exponents and activation energies for creep, which are greatly dependent on the stress and temperature. Because the creep stress is seen to cause a strongly significant enhancement of coarsening, the coarsening rate of the dispersed particles in all crept specimens is faster than that in isothermally annealed specimens. Dislocations connecting dispersoids are observed more cofrequently in crept specimens with higher stress and lower temperature. The creep strain rates in the power law creep regime were found to be predicted much better by the Shorty and Rosler/Arzt equation with the inclusion of a threshold stress and dislocation detachment mechanism. The dispersoids in this alloy were acting a source of void nucleation that finally leaded to ductile fracture within the grain so called intergranular. Each void was initiated, grown and failed at the dispersoids in the aluminium matrix. Grain boundary accommodation of the slip produced, which result in initiation of the void and then final transgranular fracture. Therefore, it was confirmed that these dispersoids played an important role in the fracture mechanism by the formation of $Al_{13}Fe_4$, $Al_{13}Cr_2$ and $Al_2O_3$.

• Journal of Food Hygiene and Safety
• /
• v.38 no.5
• /
• pp.381-389
• /
• 2023

Vibrio vulnificus, the most fatal waterborne and foodborne pathogens of 50% fatality rate in the world, is common in seawater and occurs particularly in warmer months. In this study, we investigated the toxin genes using reverse transcription-polymerase chain reaction (RT-PCR), antibiotic resistance status using Vitek, and genetic characteristics using pulsed-field gel electrophoresis (PFGE) of different V. vulnificus strains isolated from the Jeju Island seawater, distribution fishery products, and fish tanks. We examined a total of 487 samples and isolated a total of 46 strains (including overlapping strains) of V. vulnificus, 44 strains from seawater and 1 strain each from fishery products and fish tank. We detected toxin gene vvhA in all 46 strains and rtxA, viu in 8 strains (17.4%) and 9 strains (19.6%) strains, respectively. Antibiotic resistance tests indicated 100% resistance to cefoxitin antibiotics. The PFGE analysis of the 46 strains identified a total of 6 types showed 100% homology and the degree of similarity was 81.3-98.0%; however, there were no similarity between the regions and samples. These results indicate that V. vulnificus isolated from the seawater, fishery products, and fish tanks should be continuously monitored as cases of food poisoning caused by V. vulnificus with toxin genes have been reported in Jeju Island.

• Korean Journal of Microbiology
• /
• v.35 no.4
• /
• pp.307-314
• /
• 1999

This study was aimed at the investigation of the possibility of the addition of lactic acid bacteria as "starter"for the preparation of radish juice. Forty strains of lactic acid bacteria were isolated from dongchimi that was fermented by a traditional method. The isolates were assorted into 5groups, Leuconostoc mesenteroides subsp. mesenteroides (J-9), Lacobacillus brevis (J-12), Lactobacillus fermentum (J-7), Lactobacillus sake (J-20), and Lactobacillus plantarum (J-39). Leuconostoc mesenteroides was predominated in the sample of dongchimi with frequency of 52.5%. Each of the strain, which exhibited the beat growth in the species, was selected in the 5species, and investigation of the fermentation characteristcis was carried out. The fermentation were performed for 9 days at 25${\circ}C$ after the inoculation of 0.3% ($10^{6}$ cfu/㎖) to each ultra-filtrated radish juice. The pH, total acidity, content of non-volatile organic acids were examined during the fermentation period. Lactobacillus plantarum showed the highest growth rate and the growth rate of Lactobacillus sake was the lowest. The pH (6.3-6.36) and total acidity (0.09-1.0 %) fo the ultrafiltrated radish juice before fermentation were changed to 3.2-4.3 and 0.65-1.2% after 9days, respectively. The changes of the pH and total acidity were related with the growth of the lactic acid bacteria; the better growth of lactic acid bacteria, the more rapid decrease of pH and increase of the total acidity. when the amount of non-volatile organic acids were estimated during fermentation, citric acid, malic acid, malonic acid, and succinic acid were decreased in all cases. However, the content of lactic acid increased with the progression of fermentation. L. mesenteroides (J-9), L. brevis (J-12) and L. fermentum (J-7) were chosen for the candidates of the starter for the lactic fermentation of radish juice based on the biochemical analysis and sensory evaluation.

• Clinical and Experimental Pediatrics
• /
• v.48 no.1
• /
• pp.40-47
• /
• 2005

Purpose : S. pneumoniae is one of major pathogens of community-acquired respiratory infections. The rate of antibiotic resistance to this organism has increased, and resistance to multiple antimicrobial agents in a single strain of S. pneumoniae may compromise the efficacy of empiric antimicrobial treatment commonly used for respiratory infections. We did this study to find out the penicillin resistant distributions and oral antibiotics susceptibility patterns against S. pneumoniae, isolated from pediatric patients with community-acquired respiratory infections in Korea. Methods : One hundred fifty six pneumococcal isolates obtained from pediatric patients with community-acquired respiratory infections such as acute otitis media(AOM), sinusitis and pneumonia between May 2000 to June 2003. And MICs of penicillin and oral antibiotics(amoxicillin, amoxicillin-clavulanate, cefaclor) were performed by broth microdilution methods according to the NCCLS(2003a). Results : Seventy eight percent of the isolates were resistant to penicillin. The isolates, collected from AOM patients showed the highest penicillin resistance(92.7%). The resistant rates of amoxicillin (16.7%) and amoxicillin-clavulanate(9.6%), based on susceptibility breakpoints established by the NCCLS, were markedly lower than these of penicillin. But, the resistant rate of cefaclor was very high, above 95%. Conclusion : We concluded that pneumococci isolated from study cases may be one of the world's highest penicillin resistant rates. But, amoxicillin and amoxicillin-clavulanate can be used as a first-line antibiotics. Finally, we hope that a continuous surveillance study to monitor resistant patterns of pneumococcal respiratory infections will be needed for the standard guidelines of empiric antibiotic treatment.

• Korean Journal of Poultry Science
• /
• v.40 no.4
• /
• pp.299-304
• /
• 2013

Tracheal epithelial cells (TECs) are an important tool for studies of viral respiratory diseases. Primary TECs have been cultured from human, mouse and hamster. It is also necessary to diagnose viral respiratory disease and reveal infection mechanisms in chicken. In this study, we isolated tracheal epithelial layers from tracheal of 20-day-old chicks and cultured primary TECs from the isolated layers. Ciliated cells which were a typical morphology of TECs were observed in cultured primary TECs and maintained until cell passage 5 (15 to 20 days). When we analyzed expression patterns of epithelial marker genes (retinoic acid responder, FGF-binding protein, virus activating protease (VAP) in TECs compared to immortalized chicken embryonic fibroblast cell line (DF-1), all the marker genes are highly expressed in TECs than in DF-1. When TECs were cultured with 0.1 and 1 MOI of ND virus (rNDV-GFP strain) to test the susceptibility of TECs for ND virus, 12.6% and 48.2% of the incubated TECs were infected respectively. In addition, when DF-1 was incubated with 1 MOI of ND virus, the virus infection rate of DF-1 was three times lower than the virus infection rate of TECs. These data could contribute to study infection mechanisms of viral respiratory diseases and control them in chicken.

• Korean Journal of Organic Agriculture
• /
• v.18 no.3
• /
• pp.347-361
• /
• 2010

This study was carried out to investigate the effects of wormwood (Artemisia sp.) addition on the growth performance, nutrients utilization and abdominal fat deposition of broiler chickens. Two hundred twenty five and two-day old Arboracre strain male commercial broiler chicks were distributed to 5 treatments with wormwood supplementation levels; C(O%), $T_1$ (1%), $T_2$ (3%), $T_3$ (5%), and $T_4$ (10%) and with 3 replications each with 5 birds for five weeks. Body weight gain during the experiment was improved in $T_1$ (1723.0g) compared with that of $T_3$ (1557.7g) and $T_4$ (1450.7g) (P<0.05). Feed intake was significantly (P<0.05) increased as the levels of wormwood addition increased (C: 2653.8g, T1: 2852.0, $T_2$: 2900.3, $T_3$: 2900.7g, T4: 2954.7g). Feed conversion rate (feed/gain) was significantly (P<0.05) increased as the levels of wormwood addition increased (C: 1.55, $T_1$: 1.66, $T_2$: 1.70, $T_3$: 1.86, $T_4$: 2.04). The days reaching to 2.0kg of body weight were expected to be 43.2 days in control, whereas those of group T1 were reduced to 42.6 days by 0.6 day from control. Nutrient utilization and abdominal fat deposition in the experiment were significantly decreased (P<0.05) and small intestine contents in the broilers was significantly increased (P<0.05) as the levels of wormwood addition increased. Therefore, although there was no significant improvement for the performance of broiler chickens with the dietary supplementation of wormwood meal, less than 1% addition of wormwood to broiler diets might have beneficial for human health by reducing the abdominal fat deposition of the broiler chicknens.

• Korean Journal of Microbiology
• /
• v.17 no.3
• /
• pp.97-130
• /
• 1979

Many industrial processes those employ bacteria are subjected to phage infestations. In L-glutamic acid fermentions using acetic acid, the phage infestations of the organisms have been recently recognized. In efforts to elucidate the sources of phage contamination involved in the abnormal fermentation, a series of study was conducted to isolate the phages both from the contents of abnormally fermented tanks and the soil or sewage samples from the surroundings of a fermentation factory, to define major charateristics of the phage isolates, and finally to determine the correlation between the phage isolates and temperate phages originating from the miscellaneous bacterial species isolated from the soil or sewage samples. The results are summarized as follows; 1) All phages were isolated from the irregular fermentation tanks and soil or sewage samples, and they were designated as phage PR-1, PR-2, PR-3, PR-4, PR-5, PR-6, and PR-7, in the order of isolation. These PR-series phages were proved to be highly specific for the variant strains of Br. lactofermentum only, namely, phage PR-1 and PR-2 for Br. lactofermentum No. 468-5 and phage PR-3~PR-7 for Br. lactofemrentum No. 2256. By cross-neutralization test, the 7 phagescould be subdivided into 3 groups, i. e., phage PR-I and PR-2 the first, phage PR-3, PR-4, PR-5, PR-6 the second, and the phage PR-7 the third. 2) The 7 phages were virulent under the experimental conditions. They produced plaques with clear and relatively sharp margins without distinct halo. The mean sizes of plaques were 1.5mm in diameter for phage PR-1 and PR-2, and 1. Omm for phages PR-3~PR-7. Double layer technique modified by Hongo and described by Adams, was applied to assay of the PR-series phages. The factors influencing the plaques were as follows;young age cells of host bacteria cultured for 3-6 hours represented the largest number and size, optimum was pH 7.0, incubation temperature was $30^{\circ}C$, and agar concentration and amount of overlayer medium were 0.6% and 0.2ml, respectively. 3) PR-series phages were stable in 0.05M tris buffer and 0.1M ammonium acetate buffer solution. The addition of $5{\times}10^{-3}M$ magnesium ion effectively increased the stability. Thermostability experiments indicated that PR-series phages were stable at the teinperture between $50^{\circ}{\sim}55^{\circ}C$ in nutrient medium, $45^{\circ}{\sim}50^{\circ}C$ in buffer solution. However, the phages mere completely inactivated at 603C and 65$^{\circ}$C within 10 minutes. The phages were stable at the range of pH6~9 in nutrient medium and of pH 8-9 in buffer solution, respectively. Exposure of the phages to UV for 25, 60 and 100 seconds resulted in the complete loss of infectivily, respectively. 4) Electron microscopy showed that PR-series phage particles exhibited rather similar morphology, differing in the size All of PR-series phages had a multilateral head and had a simple long tiil about three to five times long as compared with head. By the size, phage PR-1 and PR-2, PR-3, PR-4, PR-5, and PR-6 and PR-7 were classified into same groups, respectively. The head and tail size of phage PR-1, PR-5, PR-5(T) and PR-7 were 85nm, 74nm and 235nm and 350mm, and 72nm and 210nm, respectively. 5) Nucleic acids of PR-series phages were double stranded DNA. The G+C contents of phage PR-1, PR-5 and PR-7 were 56.1, 52.9 and 53.7, respectively. The values of G+C contents derived from the $T_m$ were in agreement with the chemically determined values. 6) PR-series phages effectively adsorbed on their host bacteria at the rate of more than 90% during 5 min. K value for phage PR-1, PR-5 and PR-7 were calculated to be $6{\times}10^9 ml$ per minute, respectiveky. The pH of the medium did effect adsorption rate, but both temperature and age of host cells did not. Generally, optimum adsorption condition of phages seemed to be almost same as optimum growth conditions of host bacteria. 7) In one-step growth experiments, the latent periods at $30^{\circ}C$ for PR-1, and PR-7 were about 70, 50 and 55 min, respectively. The corresponding average burst size was 200, 70 and 90, respectively. Lpsis period according to the multiplicity of infection and a phage series. In case of m. o. i. 100, strain No. 2256 (PR-5) and No. 468-5(PR-1) failed to grow and turbidity decreased after 50 and 70min, respectively. 8) In the lysate of a plaque purified phage PR-5 infected bacteria, there observed 2 types ofphage particles, i. e., phage PR-5 and PR-5 (T) of similar morphology but differing at the length of phage tail, and phage tail like particles. The phage taillike particles could be divided into 4 types by the length. Induction experiments of Br. lactofermentum with UV irradiation, mitomycin C or bacitracin treatment produced neither phage PR-5 (T) or phage tail-like particles. 9) No lysis occured when the growth of 7 strains of miscellaneous bacteria, isolated from soil and sewage samples, were inoculated with either phage PR-5 (T) or phage tail-like particles the inoculation of phage PR-5 pellet resulted in the growth inhibition of the orgainsms in the spot test. The lysates obtained from 3 miscellaneous soil derived bacteria following mitomycin C treatment the growth of Br. lactofermentum, but did not lyze the bacterium.