• 한국강구조학회 논문집
• /
• 제23권2호
• /
• pp.179-188
• /
• 2011

건물에 요구되는 성능수준에 대해 명확히 명시하지 못하는 현행의 설계법에 대한 대안으로 성능중심설계법의 필요성이 부각되고 있다. 미국과 일본 등의 선진국에서는 이미 성능중심설계의 기반을 구축하기 위한 연구가 진행중이며 최근 국내에서도 성능설계에 관한 연구가 진행된 바 있으나 아직 전반적인 관련기술이 낙후되어 있는 실정이다. 한편 지진동에 의한 수평력 작용시 건물의 기둥, 특히 하층부의 외주는 전단휨과 함께 전도모멘트에 의한 변동축력을 받게 된다. 이러한 변동축력은 부재의 국부좌굴시점 및 열화역 이후의 종국거동에 영향을 미칠 가능성이 크다. 따라서 본 연구에서는 변동축력을 받는 기둥부재 실험을 실시하여 변동축력으로 인한 국부좌굴 시점 및 부재의 종국거동 등의 구조성능에 대하여 분석하였다. 또한 이를 바탕으로 강구조 건축물의 성능중심설계에 대한 성능한계를 층간변위각의 형태로 제안한 국내연구의 타당성을 검증하였다.

• Advances in Computational Design
• /
• 제4권4호
• /
• pp.327-342
• /
• 2019

Rehabilitation and retrofitting of structures designed in accordance to standard design codes is an essential practice in structural engineering and design. For steel structures, one of the challenges is to strengthen the panel zone as well as its analysis in moment-resisting frames. In this research, investigations were undertaken to analyze the influence of the panel zone in the response of structural frames through a computational approach using ETABS software. Moment-resisting frames of six stories were studied in supposition of real panel zone, different values of rigid zone factor, different thickness of double plates, and both double plates and rigid zone factor together. The frames were analyzed, designed and validated in accordance to Iranian steel building code. The results of drift values for six stories building models were plotted. After verifying and comparing the results, the findings showed that the rigidity lead to reduction in drifts of frames and also as a result, lower rigidity will be used for high rise building and higher rigidity will be used for low rise building. In frames with story drifts more than the permitted rate, where the frames are considered as the weaker panel zone area, the story drifts can be limited by strengthening the panel zone with double plates. It should be noted that higher thickness of double plates and higher rigidity of panel zone will result in enhancement of the non-linear deformation rates in beam elements. The resulting deformations of the panel zone due to this modification can have significant influence on the elastic and inelastic behavior of the frames.

• 대한건축학회논문집:구조계
• /
• 제35권4호
• /
• pp.135-146
• /
• 2019

Deep beam has high section modules compared with shallow beam of the same weight. However, deep beam has low rotational capacity and high possibility of brittle failure so it is not possible to apply deep beams with a long span to intermediate moment frames, which should exhibit a ductility of 0.02rad of a story drift angle of steel moment frames. Accordingly, KBC and AISC limit the beam depth for intermediate and special moment frame to 750mm and 920mm respectively. The purpose of this paper is to improve the seismic performance of intermediate moment frame with 1200mm depth beam. In order to enhance vulnerability of plastic deformation capacity of deeper beam, Multi-Reduced Taper Beam(MRTB) shape that thickness of beam flange is reinforced and at the same time some part of the beam flange width is weakened are proposed. Based on concept of multiple plastic hinge, MRTB is intended to satisfy the rotation requirement for intermediate moment frame by dividing total story drift into each hinge and to prevent the collapse of the main members by inducing local buckling and fracture at the plastic hinge location far away from connection. The seismic performance of MRTB is evaluated by cyclic load test with conventional connections type WUF-W, RBS and Haunch. Some of the proposed MRTB connection satisfies connection requirements for intermediate moment frame and shows improved the seismic performance compared to conventional connections.

• Earthquakes and Structures
• /
• 제20권2호
• /
• pp.149-160
• /
• 2021

Buildings made using the locally available clay materials are amongst the least expensive forms of construction in many developing countries, and therefore, widely popular in remote areas. It is despite the fact that these low-strength masonry structures are vulnerable to seismic forces. Since transporting imported materials like cement and steel in areas inaccessible by motorable roads is challenging and financially unviable. This paper presents, and experimentally investigates, adobe masonry structures that utilize the abundantly available local clay materials with moderate use of imported materials like cement, aggregates, and steel. Shake-table tests were performed on two 1:3 reduce-scaled adobe masonry models for experimental seismic testing and verification. The model AM1 was confined with vertical lightly reinforced concrete columns provided at all corners and reinforced concrete horizontal bands (i.e., tie beams) provided at sill, lintel, and eave levels. The model AM2 was confined only with the horizontal bands provided at sill, lintel, and eave levels. The models were subjected to sinusoidal base motions for studying the damage evolution and response of the model under dynamic lateral loading. The lateral forcedeformation capacity curves for both models were developed and bi-linearized to compute the seismic response parameters: stiffness, strength, ductility, and response modification factor R. Seismic performance levels, story-drift, base shear coefficient, and the expected structural damages, were defined for both the models. Seismic performance assessment of the selected models was carried out using the lateral seismic force procedure to evaluate their safety in different seismic zones. The use of vertical columns in AM1 has shown a considerable increase in the lateral strength of the model in comparison to AM2. Although an R factor equal to 2.0 is recommended for both the models, AM1 has exhibited better seismic performance in all seismic zones due to its relatively high lateral strength in comparison to AM2.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권2호
• /
• pp.52-59
• /
• 2015

본 논문에서는 효과적인 제진설계를 구현하기 위한 설계기술 개발의 일환으로 20층 라멘조 형식의 공동주택을 대상으로 최근 개발된 등 방성감쇠장치 (일명 카고메감쇠장치)를 적용하여 대상구조물-카고메감쇠장치-지지구조물로 구성된 새로운 형식의 시스템 (Kagome Damper System : KGDS)을 제안하고, 대상구조물과 지지구조물의 강성차, 감쇠장치의 크기 및 지지구조물의 적용 층수 등을 변수로 수치해석을 수행하여 제진효과를 검토해 보았다. 해석결과, 밑면전단력과 최상층 최대응답변위 감소라는 관점에서 유효한 제진효과를 얻기 위해서는 지지구조물을 3개층 높이로 설치할 경우, 대상구조물과 지지구조물 간의 강성비는 약 6.4배 이상, 감쇠장치의 사이즈는 $700{\times}700mm$ 이상을 확보할 필요가 있으며, 지지구조물을 5개층 높이로 설치할 경우에는 대상구조물과 지지구조물 간의 강성비는 약 7.0배 이상, 감쇠장치의 사이즈는 $500{\times}500mm$ 이상을 확보할 필요가 있는 것으로 판단된다.

• Earthquakes and Structures
• /
• 제7권4호
• /
• pp.587-607
• /
• 2014

Progressive collapse, which is referred to as the collapse of the entire building under local damages, is a common failure mode happened by earthquakes. The collapse process highly depends on the whole structural system. Since, asymmetry of the building plan leads to the local damage concentration; it may intensify the progressive collapse mechanism of asymmetric buildings. In this research the progressive collapse of regular and irregular 6-story RC ordinary moment resisting frame buildings are studied in the presence of the earthquake loads. Collapse process and collapse propagation are investigated using nonlinear time history analyses (NLTHA) in buildings with 5%, 15% and 25% mass asymmetry with respect to the number of collapsed hinges and story drifts criteria. Results show that increasing the value of mass eccentricity makes the asymmetric buildings become unstable earlier and in the early stages with lower number of the collapsed hinges. So, with increasing the mass eccentricity in building, instability and collapse of the entire building occurs earlier, with lower potential of the progressive collapse. It is also demonstrated that with increasing the mass asymmetry the decreasing trend of the number of collapsed beam and column hinges is approximately similar to the decreasing trend in the average story drifts of the mass centers and stiff edges. So, as an alternative to a much difficult-to-calculate local response parameter of the number of collapsed hinges, the story drift, as a global response parameter, measures the potential of progressive collapse more easily.

• Structural Engineering and Mechanics
• /
• 제63권2호
• /
• pp.147-160
• /
• 2017

In this study, the optimum parameters of Tuned Mass Dampers (TMDs) are proposed using Gravity Search Algorithm (GSA) and Particle Swarm Optimization (PSO) to reduce the responses of the structures. A MATLAB program is developed to apply the new approach to the benchmark 10 and 40-story structures. The obtained results are compared to those of other optimization methods used in the literature to verify the developed code. To show the efficiency and accuracy of the proposed methods, nine far-field and near-field worldwide earthquakes are applied to the structures. The results reveal that in the 40-story structure, GSA algorithm can reduce the Relative Displacement (RD) and Absolute Acceleration (AA) up to 43% and 21%, respectively while the PSO decreases them by 50% and 25%, respectively. In contrast, both GSA and PSO algorithms reduce the RD and AA about 29% and 21% for the 10-story structure. Furthermore, using the proposed approach the required TMD parameters reduce by 47% and 63% in the 40 and 10-story buildings in comparison with the referenced ones. Result evaluation and related comparison indicate that these methods are more effective even by using smaller TMD parameters resulting in the reduction of acting force from TMD, having smaller stiffness and damping factors while being more cost effective due to its decreased parameters. In other words, the TMD with optimum parameters can play a positive role in both tall and typical structures.

• 한국전산구조공학회논문집
• /
• 제13권2호
• /
• pp.271-278
• /
• 2000

본 연구에서는 철골조 건물의 내진 보강 방법으로 점탄성 감쇠기의 적용과 효과에 대하여 성능에 기초한 내진 설계의 관점에서 연구하였다. 먼저 단자유도계 구조물을 대상으로 입력된 지진에너지의 소산에 대한 감쇠기의 효과에 대하여 연구하였다. 설계하중으로 중력하중을 적용한 5층 건물과 중력하중과 풍하중을 적용한 10층과 20층 건물에 대하여 해석을 수행하였다. 비선형 시간이력해석을 수행하기 위하여 성능에 기초한 내진설계기준(안)에 제시된 표준 설계응답스펙트럼을 각 지반종류와 성능목표에 대하여 구성하고, 이를 바탕으로 인공지진을 생성하였다. 해석결과에 따르면 층간변위를 성능기준으로 적용하였을 때 모든 모델이 연약지반(기능수행 성능목표)을 제외한 대부분의 지반조건에서 기준안에 제시된 성능목표를 만족하였다. 또한 적당한 위치에 점탄성 감쇠기를 설치함으로써 내진성능을 향상시키고 구조물이 탄성적으로 거동하도록 유도함을 보였다.

• Steel and Composite Structures
• /
• 제15권3호
• /
• pp.323-342
• /
• 2013

In the case of seismic-resistant composite dual moment resisting and eccentrically braced frames, the current design practice is to avoid the disposition of shear connectors in the expected plastic zones, and consequently to consider a symmetric moment or shear plastic hinges, which occur only in the steel beam or link. Even without connectors, the real behavior of the hinge may be different from the symmetric assumption since the reinforced concrete slab is connected to the steel element close to the hinge locations, and also due to contact friction between the concrete slab and the steel element. At a larger level, the structural response in the case of important seismic motions depends directly on the elasto-plastic behavior of elements and hinges. The numerical investigation presented in this study summarizes the results of elasto-plastic analyses of several steel frames, considering the interaction of the steel beam with the concrete slab. Several parameters, such as the inter-story drift, plastic rotation requirements and behavior factors q were monitored. In order to obtain accurate results, adequate models of plastic hinges are proposed for both the composite short link and composite reduced beam sections.

• 한국지진공학회논문집
• /
• 제24권1호
• /
• pp.29-37
• /
• 2020

This study is to investigate the effect of a retrofitted reinforced concrete frame with non-seismic details strengthened by embedded steel moment frames with an indirect joint, which mitigates the problems of the direct joint method. First, full-scale experiments were conducted to confirm the structural behavior of a 2-story reinforced concrete frame with non-seismic details and strengthened by a steel moment frame with an indirect joint. The reinforced concrete frame with non-seismic details showed a maximum strength of 185 kN at an overall drift ratio of 1.75%. The flexural-shear failure of columns was governed, and shear cracks were concentrated at the beam-column joints. The reinforced concrete frame strengthened by the embedded steel moment frames achieved a maximum strength of 701 kN at an overall drift ratio of 1.5% so that the maximum strength was about 3.8 times that of the specimen with non-seismic details. The failure pattern of the retrofitted specimen was the loss of bond strength between the concrete and the rebars of the columns caused by a prying action of the bottom indirect joint because of lateral force. Furthermore, methods are proposed for calculation of the specified strength of the reinforced concrete frame with non-seismic details and strengthened by the steel moment frame with the indirect joint.