• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.3
• /
• pp.77-83
• /
• 2010

"The prohibition of careless or reckless flight" is the regulation specified not only in the national air law but ICAO ANNEX and FAR. This article(item) has not been categorized properly unlike other items and the question such as why this is described as a fundamental and essential act can be answered only by the party subjected to administrative measures in case of Korea and this kind of violation is so rare that it is not easy to understand the legal meaning and the function of the term, "The prohibition of careless or reckless flight" In case of U.S where aviation cases are common, the distinction between the term "careless" or "reckless" operation depends on whether to recognize the given situation. Some incidents happened by failing to aware NOTAM, violating ATC, or T/W landing where a pilot did not recognize the violation itself are considered to be "Careless" flight. Others such as low altitude high speed flight, approximate flight, Rejecting ATC instruction where a pilot intends to or is remiss in safety are regarded as "Reckless" flight. For pilots who are required to take the highest level of care from preparing for flight to stopping engines or completely disembarking passengers from a plane, the clear understanding of the most basic concept of "careless" or "reckless" flight should be emphasized for the safe flight and it is the time for the authorities to set a standard for proper measures by definite legal interpretations.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.16 no.2
• /
• pp.69-76
• /
• 1980

This paper describes the measurement of the underwater noises produced by the engine vibration around the engine room of stern trawler MIS Sae-Ba-Da(2275GT, 3,600 PS) and pole kner M/S Kwan-Ak-San (243 GT, 1000 PS) while the ship is stopping. The underwater noise pressure level was measured with the underwater level meter of which measuring range is 100 to 200 dB(re bLPa). A and B denotes the maximum pressure level measured at right beneath the bottom of the engine room, while the main engine of the Sae-Ba-Da revoluted at 750 and 500 rpm, respectively. C denotes that of the main engine of the Kwan-Ak-San revoluted at 350 rpm, and D that of the generator of the Sae-Ba-Da revoluted at 720 rpm. Thus A, B, C and D were set for the standard sound source for the experiment. The results obtained are as follows: 1. The noise Pressure level at A, B, C and D were 170.5,165,153 and 158dB, respectively. 2. When the check points distanted vertically 1, 10, 20, 30, 40, 50m from the sound source, the underwater noise presure levels were 170.5, 155, 148, 144 and 138 dB and the directional angle was 116\ulcorner in case of A. 3. The sound level attenuated at the rate of 20dB per 10" meters of the horizontal distance from the sound sources. 4. The frequency distribution of the noise was 100Hz to 10KHz and predominant frequency was 700 to 800Hzminant frequency was 700 to 800Hz

• Journal of Korea Game Society
• /
• v.19 no.1
• /
• pp.5-14
• /
• 2019

This paper presents a practical method to compute the closest approach distance of two ellipsoids in their inter-center direction. This is the key technique for collision handling in the dynamic simulation of rigid and deformable bodies approximated with ellipsoids. We formulate a set of equations with the inter-center distance and the contact point and normal for the two ellipsoids contacting each other externally. The equations are solved using fixed-point iteration and Aitken's delta-squared process. In addition, we introduce a novel stopping criterion expressed in terms of the error in distance. We demonstrate the efficiency and practicality of our method in various experiments.

• Journal of KIISE
• /
• v.43 no.4
• /
• pp.404-410
• /
• 2016

Automated road map generation poses significant research challenges since GPS-based navigation systems prevail in most general vehicles. This paper proposes an automated detecting method for intersection points using GPS vehicle trajectory data without any background digital map information. The proposed method exploits the fact that the trajectories are generally split into several branches at an intersection point. One problem in previous work on this intersection detecting is that those approaches require stopping points and direction changes for every testing vehicle. However our approach does not require such complex auxiliary information for intersection detecting. Our method is based on partial trajectory matching among trajectories since a set of incoming trajectories split other trajectory cluster branches at the intersection point. We tested our method on a real GPS data set with 1266 vehicles in Gangnam District, Seoul. Our experiment showed that the proposed method works well at some bigger intersection points in Gangnam. Our system scored 75% sensitivity and 78% specificity according to the test data. We believe that more GPS trajectory data would make our system more reliable and applicable in a practice.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.367-371
• /
• 2019

The molding for hollow products used widely in industry is rotational molding by heating and cooling. Uniform cooling is required to improve the quality of the product, and rapid cooling is required to improve the productivity. In this paper, the cooling condition is largely classified into the case of no forced cooling by the fan and forced cooling by the fan. In addition, when forced cooling by the fan is not performed, the condition for stopping the molding machine horizontally and the condition for stopping the molding machine vertically were classified. To confirm the forced cooling by the fan, the conditions were set such that only the molding machine rotates while the fan is not running and the upper and lower fans operate when only the lower fan is operated. The surface temperature of the rotary molding machine was analyzed by the STAR-CCM+ program for the case of air-cooling. The temperature distribution of the rotary molding machine was analyzed for five conditions and the temperature distribution for cooling was compared under each condition. Among the five cases, Case 4 was lowest at approximately 35 ℃ after 900sec.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.42 no.5 s.305
• /
• pp.123-136
• /
• 2005

We propose a recognition system for superimposed patterns based on selective attention model and SVM which produces better performance than artificial neural network. The proposed selective attention model includes attention layer prior to SVM which affects SVM's input parameters. It also behaves as selective filter. The philosophy behind selective attention model is to find the stopping criteria to stop training and also defines the confidence measure of the selective attention's outcome. Support vector represents the other surrounding sample vectors. The support vector closest to the initial input vector in consideration is chosen. Minimal euclidean distance between the modified input vector based on selective attention and the chosen support vector defines the stopping criteria. It is difficult to define the confidence measure of selective attention if we apply common selective attention model, A new way of doffing the confidence measure can be set under the constraint that each modified input pixel does not cross over the boundary of original input pixel, thus the range of applicable information get increased. This method uses the following information; the Euclidean distance between an input pattern and modified pattern, the output of SVM, the support vector output of hidden neuron that is the closest to the initial input pattern. For the recognition experiment, 45 different combinations of USPS digit data are used. Better recognition performance is seen when selective attention is applied along with SVM than SVM only. Also, the proposed selective attention shows better performance than common selective attention.

• Journal of Korean Society of Forest Science
• /
• v.100 no.4
• /
• pp.664-671
• /
• 2011

Random Walk Model can predict the sediment areas of debris flow but it must be extracted three parameters fitted topographical environment. This study developed the method to extract the optimal values of three parameters - Once flowing volume, Stopping slope and Gravity weight - for Random Walk Model. And the extracted parameters were validated by aerial photographs of the debris flowed area. To extract the optimal parameters was randomly performed, limiting the range values of three parameters and developing an accuracy decision method that is called the rate of concordance. The set of the optimal parameters was decided on highest the rate of concordance and a consistency. As a result, the optimal parameters in Bonghwa county were showed that the once flowing volume is $1.0m^3$, the stopping slope is $4.2^{\circ}$ and the gravity weight is 2 when the rate of concordance is -0.2. The validating result of the optimal parameters showed closely that the rate of concordance is average -0.2.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.50-56
• /
• 2011

To meet the NOx limit without a penalty of fuel consumption, Urea-SCR system is currently regarded as promising NOx reduction technology for diesel engines. SCR system has to achieve maximal NOx conversion in combination with minimal $NH_3$ slip. In this study, map based open loop control for urea injection was developed and assessed in the European Transient Cycle (ETC) for heavy duty diesel engine. The basic urea quantity set-value which was calculated using the look up tables of engine out NOx, exhaust flow rate and optimum NSR resulted in NOx reduction of 80% and the average $NH_3$ slip of 24 ppm and maximum of 79 ppm. In order to reduce $NH_3$ slip, $NH_3$ storage control algorithm was applied to correct the basic urea quantity and reduced $NH_3$ slip levels to the average 15 ppm and maximum 49 ppm while keeping NOx reduction of 76%. With high and increasing SCR temperature, the $NH_3$ storage capacity decreases, which leads to $NH_3$ slip. The resulting $NH_3$ slip peak can be avoided by stopping or significantly reducing the urea injection during the SCR temperature gradient is over $30^{\circ}C/min$.

• Communications for Statistical Applications and Methods
• /
• v.18 no.1
• /
• pp.137-146
• /
• 2011

Long-term care insurance is a social insurance system that provides benefits to the elderly who have difficulty taking care of themselves for a period of at least 6 months. This system was started in July, 2008 and it is very important to set proper judgement ratings for the approval process. We try to develop and improve the judgement rating system using decision tree models. Our tree model is found to be more stable and efficient than the previous one.

• Tunnel and Underground Space
• /
• v.24 no.1
• /
• pp.11-20
• /
• 2014

This study analyzed the optimal routes of auxiliary vehicles in an open-pit mine that need to traverse the entire mine through many working points. Unlike previous studies which usually used the Dijkstra's algorithm, this study utilized a heuristic algorithm for the Traveling Salesman Problem(TSP). Thus, the optimal routes of auxiliary vehicles could be determined by considering the visiting order of multiple working points. A case study at the Pasir open-pit coal mine, Indonesia was conducted to analyze the travel route of an auxiliary vehicle that monitors the working condition by traversing the entire mine without stopping. As a result, we could know that the heuristic TSP algorithm is more efficient than intuitive judgment in determining the optimal travel route; 20 minutes can be shortened when the auxiliary vehicle traverses the entire mine through 25 working points according to the route determined by the heuristic TSP algorithm. It is expected that the results of this study can be utilized as a basis to set the direction of future research for the system optimization of auxiliary vehicles in open-pit mines.