• Korean Journal of Food Science and Technology
• /
• v.26 no.5
• /
• pp.567-572
• /
• 1994

Diglyceride was prepared by reaction of hydrogenated beef tallow and glycerol (GL) in the presence of a Pseudomonas lipase. Both substrates were mixed at the ratio of GL/Triglyceride of 0.5 which is the stoichiometric molar ratio for the complete conversion of triglyceride (TG) to diglyceride (DG). DG can be obtained by solid phase-glycerolysis of hydrogenated beef tallow without use of organic solvents or emulsifiers by careful control of reaction temperature. Optimized reaction temperature condition was as follows: An initial incubation at$60^{\circ}C$ for 2h followed by the first temperature shift down to $55^{\circ}C$ for 4h, and then the second shift down to $50^{\circ}C$ for up to 3 days. There was a large decrease in the content of TG during the first $60^{\circ}C$ incubation for 2h. Even a prolonged incubation at $60^{\circ}C$ could not make a change of the composition of the reaction mixture at liquid state. By controlling the temperature lower than $60^{\circ}C$, reaction mixtures were solidified. The reaction temperature at $50^{\circ}C$ below the melting temperature of hydrogenaed beef tallow gave an 71% optimum yield of DG after 72h enzymatic glycerolysis and about 73% of total DG was 1,3-DG.

• Current Photovoltaic Research
• /
• v.1 no.1
• /
• pp.38-43
• /
• 2013

$Cu(In,Ga)_3Se_5$ is a candidate material for the top cell of $Cu(In,Ga)Se_2$ tandem cells. This phase is often found at the surface of the $Cu(In,Ga)Se_2$ film during $Cu(In,Ga)Se_2$ cell fabrication, and plays a positive role in $Cu(In,Ga)Se_2$ cell performance. However, the exact properties of the $Cu(In,Ga)_3Se_5$ film have not been extensively studied yet. In this work, $Cu(In,Ga)_3Se_5$ films were fabricated on Mo-coated soda-lime glass substrates by a three-stage co-evaporation process. The Cu content in the film was controlled by varying the deposition time of each stage. X-ray diffraction and Raman spectroscopy analyses showed that, even though the stoichiometric Cu/(In+Ga) ratio is 0.25, $Cu(In,Ga)_3Se_5$ is easily formed in a wide range of Cu content as long as the Cu/(In+Ga) ratio is held below 0.5. The optical band gap of $Cu_{0.3}(In_{0.65}Ga_{0.35})_3Se_5$ composition was found to be 1.35eV. As the Cu/(In+Ga) ratio was decreased further below 0.5, the grain size became smaller and the band gap increased. Unlike the $Cu(In,Ga)Se_2$ solar cell, an external supply of Na with $Na_2S$ deposition further increased the cell efficiency of the $Cu(In,Ga)_3Se_5$ solar cell, indicating that more Na is necessary, in addition to the Na supply from the soda lime glass, to suppress deep level defects in the $Cu(In,Ga)_3Se_5$ film. The cell efficiency of $CdS/Cu(In,Ga)_3Se_5$ was improved from 8.8 to 11.2% by incorporating Na with $Na_2S$ deposition on the CIGS film. The fill factor was significantly improved by the Na incorporation, due to a decrease of deep-level defects.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.2
• /
• pp.151-157
• /
• 2005

A one-dimensional numerical model was developed to simulate vertical profiles of electron acceptors and their reduced species in benthic sediments. The model accounted for microbial degradation of organic matter and subsequent chemical reactions of interest using stoichiometric relationships. Depending on the dominant electron acceptors utilized by microorganisms, the benthic sediments were assumed to be vertically subdivided into six zones: (1) aerobic respiration, (2) denitrification, (3) manganese reduction, (4) iron reduction, (5) sulfate reduction, and (6) methanogenesis. The utilizations of electron acceptors in the biologically mediated oxidation of organic matter were represented by Monod-type expression. The mass balance equations formulated for the reactive transport of organic matter, electron acceptors, and their corresponding reduced species in the sediments were solved utilizing an iterative multistep numerical method. The ability of model to simulate a freshwater sediments system was tested by comparing simulation results against published data obtained from lake sediments. The simulation results reasonably agreed with field measurements for most species, except for ammonia. This result showed that the C/N ratio (106/16) in the sediments is lower than what the Redfield formula prescribes. Since accurate estimates of vertical profiles of electron acceptors and their reduced species are important to determine the mobility and bioavailability of trace metals in the sediments, the model has potential application to assess the stability of selected trace metals in the sediments.

• Journal of Adhesion and Interface
• /
• v.15 no.3
• /
• pp.100-108
• /
• 2014

In this work, a series of molar ratios composed with YD-128 and DDM were chosen based on the viscosity analysis. The mixtures of YD-128 and DDM with the different molar ratios were cured at $170^{\circ}C$ for 15 min followed by post cure at $190^{\circ}C$ for two hours. The thermal properties of the cured samples were investigated with DSC, TGA, DMA, and TMA. The conversion ratio of the mixtures of YD-128 and DDM (1 : 1.1) was calculated by dividing ${\Delta}H$ obtained from DSC experiments for each cured sample by ${\Delta}H$. The TGA data of the cured samples showed that the thermal stability and thermal degradation activation energy were proportional to the amount of DDM in the mixtures. However, the highest tan ${\delta}$, and the lowest thermal expansion data with DMA and TMA respectively were obtained from the stoichiometric mixture of YD-128 and DDM. Furthermore, the different ratio of mixtures were applied to test specimens to be cured at $170^{\circ}C$ to measure single lap shear strength with universal testing machine.

• Journal of the Korean Chemical Society
• /
• v.20 no.5
• /
• pp.323-332
• /
• 1976

The x or $x^0+x'$ values of the nonstoichiometric chemical formula $TiO_{2-x}$ or $Ti_{2-(x^0+x')}$ have been measured by a specially made magnetic quartz microbalance in a temperature range from 600 to $1300^{\circ}C$ under oxygen pressures of $1{\times}10^{-6} to 1 atm. The standard x or $x^0$ value of the rutile is 0.00148. The x values $under_xoxygen$ pressure of 1 atm decrease with temperatures and then the stoichiometric rutile (or x = 0) is formed at $1130^{\circ}C$. The x values varied between 0.00148 and 0.01719 at a temperature range from 600 to $1300^{\circ}C$ under $1{\times}10^{-9}{\sim}1{\times}10^{-2}$ atm oxygen pressures. The enthalpies of formation of the nonstoichiometric rutile, $H_f$, varied between 21.05 and 29.97 Kcal/mole under the above conditions. The 1/n values calculated from the plots of log X' vs. log $Po_2$ are -{\frac{1}{2}}{\sim}-{\frac{1}{4}} under low oxygen pressure range of $1{\times}10^{-6}\;to\;1{\times}10^{-4}$ atm. Many physical properties of the titanium dioxide, such as the stability of the rutile, Electrical conductivity, catalytic activity and defects, can be explained through the x values and the thermodynamic data calculated from the temperature and oxygen pressure dependences of the x' values.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.4
• /
• pp.301-305
• /
• 2007

The performance of polymer electrolyte membrane fuel cell could be decreased due to coolant leaked from connection part. Micro pump was used to put small amount of coolant and investigate the effect on fuel cell. The stoichiometric ratio of hydrogen/air was 1.5/2.0, both side of gas was fully humidified, and current density of $400mA/cm^2$ was used as standard condition in this experiment. Constant current method was used to check performance recovery from coolant effect in 3 cell stack. The performance was recovered when coolant was injected in cathode side. On the other hand, the performance was not recovered when coolant was injected in anode side. Ethylene glycol could be converted to CO in oxidation process and cause poisoning effect on platinum catalyst or be adhered on GDL and cause gas diffusion block effect resulting performance decrease. Water with nitrogen gas was supplied in anode side to check performance recovery. Polarization curve, cyclic voltammetry, electrochemical impedance spectroscopy was used to check performance, and gas chromatography was used to check coolant concentration. Constant current method was not enough in full recovery of performance. However, water injection method was proved good method in full recovery of performance.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.89-95
• /
• 2010

The chalcopyrite $Cu(In_xGa_{(1-x)})Se_2$ (CIGS) is considered to be one of the effective light-absorbing materials for thin film photovoltaic solar cells. We describe the electrodeposition of CIGS thin films in ambient laboratory conditions, and suggest the electrochemical conditions to prepare stoichiometric CIGS thin films of Ga/(In + Ga) = 0.3. In acidic solutions containing $Cu^{2+}$, $In^{3+}$, $Ga^{3+}$ and $Se^{4+}$ ions, the CIGS films of different Cu/In/Ga/Se chemical compositions were electrodeposited onto Mo/Glass substrate. The structure, morphology and chemical composition of electrodeposited CIGS films were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive X-ray spectroscopy (EDS), respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.1
• /
• pp.12-17
• /
• 1993

Growth runs of KTP single crystals were carried out by the hydrothermal method. KTP powders used for the crystal growth were prepared as a single phase by the solid state reaction of a stoichiometric mixture of $KH_2PO_4 and TiO_2$ at TEX>$800^{\circ}C$ and subsequently by the hydrothermal treatment at $250^{\circ}C$ 4m KF solution. The most effective solvents for the crystal growth of KTP were KF and K $K_2HPO_4$ solutions. Solubilities of KTP in these solutions were positive over the range $350~450^{\circ}C$.Seed crystals of good quality could be obtained by the horizontal temperature gradient method at temperatures over the range 380~430^{\circ}C$ in these solutions. The hydrothermal conditions for the high growth rates of seed crystals are as follows: growth method; vertical temperature gradient method, solvent; 4m KF or $K_2HPO_4$ solution, temperature region; $400~450^{\circ}C$, pressure region; $1000~1500kg/cm^2$, where solubility of KTP was large enough to proceed the growth. Under such conditions, seed crystals of KTP are grown at a rate of approximately 0.06-0.08mm/day in the direction of the c-axis. Morphologies of grown crystals tended to be bounded by (100), (011) and (201) faces.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.3
• /
• pp.93-98
• /
• 2005

The crystal growth of calcite at a low temperature range was carried out by the hydrothermal method using amorphous calcium carbonate which has excellent solubility in water. Amorphous calcium carbonate was prepared by the wet chemical reaction of a stoichiometric mixture of $CaCl_2\;and\;Na_2CO_3$. An important factor was the reaction temperature and time taken in preparation of the amorphous calcium carbonate. From the solubility results calculated by the weight loss method, $NH_4NO_3$ solutions were found to be the most promising solvents to grow calcite single crystals. The hydrothermal conditions for high growth rates of calcite single crystals were as follows: starting material: amorphous calcium carbonate, solvent: 0.01 m $NH_4NO_3$, temperature: $180^{\circ}C$, duration: 30 days. And properties of calcite single crystals were follows: dislocation density: $10^6{\sim}10cm^{-2}$, UV-visible transmittance: about 80% from 190 to 400 nm and birefringence: $0.17{\sim}0.18$. Also, it can be known from the FT-IR results that the absorption peak by injection of $HCO_3^-\;and\;OH^-$ ions was not shown.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.3
• /
• pp.104-107
• /
• 2005

[ $TiN_x$ ] powder have been fabrication by making of reaction between titanium powder and $Si_3N_4$ bowl during a planetary milling. Milling times were maintained for 1 hour, 5 hours, and 10 hours, respectively. The XRD result showed existence of non-stoichiometric compound of $TiN_{0.26}$ after 5 hours milling and coexistence of TiN with $TiN_{0.26}$ after 10 hours milling. Particle size distribution was investigated by particle size analyzer and microstructure was analyzed by FE-SEM. The size of titanium was decreased with increasing the milling time and the mean size of $TiN_x$ after 10 hours milling was increased by 200 nm.