• Journal of Aerospace System Engineering
• /
• v.14 no.1
• /
• pp.21-27
• /
• 2020

Aircraft should be equipped with various external stores for mission performance. Since these external stores may cause structural instability of aircraft, an evaluation of the effects between the aircraft and the external stores is required. For this purpose, an aircraft dynamic characteristics analysis reflecting an external store was performed, and the finite element model for the analysis of aircraft dynamic characteristics should simulate the dynamic characteristics of the component as accurately as possible while using a minimum of the nodes and elements. In this study, a stick model was constructed for dynamic characteristics analysis of the external fuel tank and installation pylon using MSC Patran/Nastran. For the calculation of the equivalent stiffness of the stick model, a simple beam theory was applied to construct the stick model of each part, and the validity of each stick models was confirmed by mode comparison with the fine model. Additionally, the model analysis of the stick model assembly, simulating a pylon equipped with an external fuel tank was performed to confirm that the basic modes required for the analysis of aircraft dynamic characteristics are well extracted. Finally, it was confirmed that the developed stick model assembly could be used for analysis of aircraft dynamic characteristics by comparing the errors in modes between the fine model assembly and the stick model assembly.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.830-832
• /
• 2014

In this study, friction stick-slip vibration're interpretation of the phenomenon, we used a statistical model of friction. In a previous study using a definite friction factor, but to a dynamic simulation using a constantly changing during the integration time by a Monte Carlo simulation method, not the average coefficient of friction and the dynamic friction coefficient and a constant value in this study.

• Journal of Industrial Technology
• /
• v.24 no.B
• /
• pp.207-214
• /
• 2004

An active stick which supplies force feedback to the operator is developed in this study. A mathematical model of the active stick is derived, and compared with the experimental result. It turns out that the frictional torque due to the mechanical contacts of several parts of the stick is one of the major barriers to achieve high precision operation of the stick. The frictional effect of the stick is cancelled out by using a friction observer. The efficacy of the friction observer is verified through the numerical simulation. Because of the observer dynamics, there are some limitations in exact recovering the static friction and Stribeck effect. However, the friction observer follows the real friction on the average. It's anticipated that the application of the friction observer to the closed loop control of the active stick improves the performance of the displacement versus force characteristics, which will be proved experimentally in the further study.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.233-236
• /
• 1996

This paper describes a liner state-space model for a flexible stick balencer. The method employed to generate the model utilizes a separable formulation of assumed modes to represents the transverse displacement due to bending Lagrangian dynamics are applied to determine the kinetic and potential energies for the system. The resultant dynamic equations are then organized into a state space model and linearized using Taylor series expansion method. A minimum order observer is designed to estimate unmeasurable states.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.90.6-90
• /
• 2002

An active stick which has the variable force-feel characteristics is developed. A combined position and force control strategy is mechanized using a 2-axis built-in force sensor and LVDT. The 2-axis force sensor which measures the stick force felt by the operator is developed by using strain gages and appropriate instrumental amplifiers. A mathematical model of the active stick dynamics is derived, and compared with the experimental results. The frictional torque of the stick due to the mechanical contacts of several parts makes the experimental frequency responses to be dependent on the magnitude of excitation signal, and the precision closed loop control to be difficult. A friction observe...

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.250-251
• /
• 2014

This paper investigates the stick-slip phenomena on spinning shaft. The modeling of the shaft is considered only torsional direction with nonlinear friction. The friction is adopted a negative friction-velocity slope. Based on the model, a nonlinear equation of motion is derived and analyze the stick-slip phenomena. In order to analyze the time dependent response, the nonlinear formulations are numerically solved by nonlinear Newmark method. The numerical results reveal the stick-slip phenomena on the spinning shaft system.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.55-60
• /
• 2002

In many dynamic systems, there are unwanted oscillation which may arise the reduction of performance. Especially in low sliding speed condition, the stick-slip is an important issue because it because unstable motion as well as inaccurate position control in the system. Most previous works on the stick-slip are, however, only concerned with simple modeling under the condition of constant normal force. The normal force and the amount of hydraulic oil are variable with a cylinder stroke in the telescopic boom. This paper presents the pressure variations during stick-slip with the cylinder of telescope boom. Pressure variations by stick-slip has a similar pattern to that of single mass-spring model. The stick-slip is gradually decreased by means of increased flow rate.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.1-15
• /
• 1998

Currently, computational analysis is a popular technology in automobile engineering. Finite element analysis is an excellent method for body analysis. For finite element analysis, accurate modeling is very important to obtain precise information. Stick modeling is a convenient way in that it is easy and simple. When a stick model is utilized, the joints are modified in the tuning process. A tuning method for the joint has been developed. The joints are modeled by designated beam elements. An optimization method called "Goal Programming" is employed to impose the target values. With the tuned joints, the entire optimization has been carried out. Using the "Recursive Quadratic Programming" algorithm, the optimization process determines the configuration of the entire structure and sizes of all the sections. For example, the structure of an electrical vehicle is modeled and analyzed by the method. The stick model works well since the structure is made of aluminium frames. Although the example handles an electrical vehicle, this method can be applied to general vehicle structures.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.514-517
• /
• 2015

Creative selfie stick design using freecad, ansys.

• Journal of the Korea Computer Graphics Society
• /
• v.21 no.1
• /
• pp.23-31
• /
• 2015

We present a method for creating realistic 2D stick figure animations easily and rapidly using captured motion data. Stick figure animations are typically created by drawing a single pose for each frame manually for the entire time interval. In contrast, our method allows the user to summarize an action (e.g. kick, jump) for an extended period of time into a single image in which one or more action lines are drawn over a stick figure to represent the moving directions of body parts. In order to synthesize a series of time-varying poses automatically from the given image, our system first builds a deformable character model that can make arbitrary deformations of the user's stick figure drawing in 2D plane. Then, the system searches for an optimal motion segment that best fits the given pose and action lines from pre-recorded motion database. Deforming the character model to imitate the retrieved motion segment produces the final stick figure animation. We demonstrate the usefulness of our method in creating interesting stick figure animations with little effort through experiments using a variety of stick figure styles and captured motion data.