• Journal of the Korean Applied Science and Technology
• /
• v.28 no.1
• /
• pp.6-9
• /
• 2011

Step feed process was analyzed stoichiometrically for the optimal operation conditions in this study. In case of optimal operation conditions, minimum R (sludge recycling) value, r (internal recycling ratio) value, and n (influent allocation ratio) value for the step feed process to acquire the maximum TN removal efficiency were identified by theoretical analysis. Maximum TN removal efficiency, based on stoichiometric reaction, can be obtained by controlling n value for the step feed process.

• Journal of the Korean Society for Precision Engineering
• /
• v.6 no.3
• /
• pp.24-31
• /
• 1989

By use of the machining center, step-feed drilling was operated under the variety of conditions as to materials, tools and cutting conditions. Based on this study the following conclusions can be drawn : 1) The cutting force can be diminished by utilizing the step-feed working; specially the most effective was it for the brass among the carbon steel, the brass, and the cast iron. 2) Tool life can be enlarged more than double when three-step-feed working is used. 3) For the constant cutting-depth(30mm), the most optimal number of stepping is 3.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.12
• /
• pp.46-53
• /
• 1996

Micro drilling is one of the most important machining types and its necessity becomes more and more increasing in the whole field of industry. Micro drilling, however, has few the case of practical application, because it requests high techniques : manufacturing micro drill, treating chip, producting precise hole shape and progressing machining effeciency. Micro drilling has a technical problem: drill breakage from the lack of drill rigdity and the interuption of chip. It is, therefore, essential to select the proper cutting conditions and the step fed for the method solving the lack of rigidity and the interruption of chip. Especially, step feed is very efficient to avoid the breakage of drill, but bring about reducing of cutting efficiency. The study on step feed must be requested more than the present in the near future. The purpose of this paper is to investigate experimentally about cutting conditions which affect on tools and round errors and to estimate about the effect of step feed as well as optimal step feed size to solve the breakage of drill.

• Korean Journal of Poultry Science
• /
• v.21 no.4
• /
• pp.257-266
• /
• 1994

Three protein feeding systems for egg-type pullets involving conventional step-down protein 18-15-12%), step-up protein(12-15-18%) and single-stage low protein (13-13-13%) with an iso-energy level of 2,900 ME kcal /kg were compared to examine the effect on pullet growth and subsequent laying performance. During the growing period, pullets subjected to the step-up and single-stage low protein feeding systems were lighter in body weight and consumed less feed and netabolizable energy than those on the conventional step-down protein feeding system(P<0.05). 3ut the pullets on the step-up protein diet consumed more protein, and those on the single-stage low protein diet consumed less protein than those on the step-down protein diet(P<0.05). Also, he feed cost was less in pullets on the single-stage low protein diet than in those on the other systems(P<0.05). During the laying period, sexual maturity was later in hens reared on the step-up and single-stage low protein diets than in those on the step-down protein diet(P<0.05), however, average hen-day egg production and egg weight were not significantly affected by the protein feeding systems in the growing period. Daily feed intake and feed required per egg were significantly reduced in hens on the single-stage low protein diet compared to those on conventional protein feeding system(P<0.05). It was concluded that the 13% single-stage low protein feeding system produced smaller pullets with less feed, energy, protein, and feed cost during the growing period, and hens reared on that system consumed less feed during the laying period without any impairment of production compared to the conventional rearing system.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.1
• /
• pp.62-70
• /
• 2005

Step-feed process for biological nitrogen removal were analyzed numerically for the each unit and final total nitrogen(TN) effluent by water quality management(WQM) model and the results were compared data from these wastewater treatment plants. No bugs and logic error were occurred during simulation work. All of the simulation results tried to two times were obtained and both results were almost same as this model has become good reappearance. It was concluded that most of nitrogen removal occurred in the first oxic tank. Thus the controlling of the first anoxic tank may be more important in term of nitrogen removal. Also each unit of simulation result was kept good relationship with that of measured data. Accordingly this WQM model has good reliance. Finally, WQM model can predict final TN effluent within ${\pm}6.0mg/{\ell}$.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.66-69
• /
• 2008

In this paper, The author present a load current feed-forward compensator by method that improve voltage controller of Step-down Chopper to get stable output voltage to sudden change of load current. To confirm the characteristicsof a presented load current feed -forward compensator compared each transfer function of whole system that load current feed-forward compensator is added with transfer function of whole system that existent voltage controller is included using Mason gains formula in Root locus and Bode diagram. As a result the pole of system is improved, extreme point of the wave and system improves, and size of peak value and phase margin of break frequency in resonance frequency confirmed that is good. Therefore, presented control technique could confirm that reduce influence by perturbation and improves stationary state and dynamic characteristics in output of Step-down Chopper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.675-680
• /
• 2010

This study was investigated to complement nitrogen removal of low concentration influent municipal sewage. The following are the results of the effect of Internal Recircularion and Step Feed rates on Treatment efficiency at a BOD low concentration influent municipal sewage. Up to 90.0% of BOD, 87.8% of COD, 71.0% of T-N, 75.3% of T-P were removed on average at a low concentration influent. Whereas BOD and T-P were removed without any relations to Step Feed rates, T-N was influenced. Nitrogen removal efficiencies in 80% of Step Feed rates was 65%, which was caused by the lack of Carbon Source for denitrification. Nitrogen removal efficiency in 40% of Step Feed rates was 58%, which means it was not removed but dischared. Consequently, the efficiency was 73%, 80%, and 78% in 70%, 60% and 50% of Step Feed rates, which was concluded as the best range of Step Feed rates. Nitrogen removal efficiency increased under the condition of Internal Recircularion. At over 150% of Internal Recircularion rate, the efficiencies were not affected any more. It is believed that lots of Recircularion caused inflow of DO to anoxic tank. Therefore, the most appropriate Internal Recircularion rate can be concluded as 50~150%.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.19 no.5
• /
• pp.143-149
• /
• 2009

The hash function ARIRANG is one of the 1st round SHA-3 candidates. In this paper, we present preimage attacks on ARIRANG with step-reduced compression functions. Our attack finds a preimage of the 33-step OFF(Original FeedForward1) variants of ARIRANG, and a preimage of the 31-step MFF(Middle FeedForward1) variants of ARIRANG. Its time complexity is about $2^{241}$ for ARIRANG-256 and $2^{481}$ for ARIRANG-512, respectively.

• Korean Journal of Poultry Science
• /
• v.49 no.4
• /
• pp.273-279
• /
• 2022

The objective of this study was to evaluate an in vitro procedure to estimate the crude protein (CP) digestibility of feed ingredients and mixed diets in broiler chickens. The apparent ileal digestibility (AID) of the CP was measured using 23-d-old male broilers. Three experimental diets, containing three feed ingredients, namely soybean meal (SBM), canola meal (CM), and corn distiller's dried grains with solubles (DDGS), were used as the sole source of CP. A 2-step in vitro procedure was used to estimate in vivo CP digestibility; all the experiments were performed in triplicate. In step 1, the feed ingredient and mixed diet samples were incubated for 4 h at 40 °C with a pH 2.0 pepsin solution, and in step 2, the flasks were incubated for 12 h at 40 °C with a pH 6.8 pancreatin solution. Following incubation, all the samples were filtered; the undigested residues were collected and pooled together to analyze the undigested CP concentration. The in vitro CP digestibility of mixed diets and feed ingredients were 93.2% and 93.0% for SBM, 86.8% and 86.7% for CM, and 83.8% and 79.1% for DDGS, respectively. The coefficients of determination (R2) between the CP digestibility values for the feed ingredients and the in vitro CP digestibility values for the feed ingredients or respective mixed diets were 0.87 or 0.67. The results of the study demonstrated that the in vitro CP digestibility values obtained from the respective mixed diets were better estimates than the values obtained from the individual feed ingredients to predict the AID of CP in feed ingredients fed to broiler chickens.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.1
• /
• pp.81-88
• /
• 1999

This paper was carried out to know the influence of advanced austempered ductile cast iron (ADI) on the tool life and mechanical properties of drilling machinability. For manufactured method of ADI, the spheroidal graphite cast iron were austenized at 90$0^{\circ}C$ for 1 hour and then austempered for 2 hour at 37$0^{\circ}C$ in the salt bath. And interrelationship has been investigated between tool life and mechanical characteristics of specimen material on drilling condition when the ordinary and step-feed drilling are carried out to drill holes of specimens. Tensile strength and hardness of ADI decrease and elongation of ADI increases with the increase austempered temperature. It is known that about 2 times of tool life in the case of step-feed decreases compared with ordinary feed due to the high hardness of ADI and hardness ascribed to the fact that retained austenite became to martensite state due to cutting heat in drilling. Under the constant feed rate 0.1mm/rev relation between hardness and length of end tip after drilling can be formularized to Hv=$788.46L^{-0.096}$ for the cutting speed 6.1m/min.