• 대한조선학회지
• /
• 제16권3호
• /
• pp.25-33
• /
• 1979

The relation between the welding conditions and welding distortions were studied with the weld parameters, current, welding speed and plate thickness, and the form of the distortions were derived theoretically. To derive these formulas, the temperature distribution on the plane normal to the direction of the weld line was assumed to be parabolic. Both the theoretical studies for the transverse shrinkage and angular distoction were compared with the experiments. The experiments were performed on the fundamental cases of a bead welds on rectangular mild steel plates. It was found that the distoction formulas were in good agreement with the results of the experiments. The formulas for the calculation of the distortion were established for the case of bead on plate weld using rectangular mild steel plate and the KS E4313, $4mm\phi$ welding rod.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.613-616
• /
• 2006

The purpose of the this study of to define the critical corrosion amount of the steel cause the cracking of concrete cover. The major variables of the critical corrosion amount are concrete strength and thick of the concrete cover. In this experiment, the constant of stress concentration is added by a new variable. As a result of the experiment, it is confirmed to less decrease in the critical corrosion amount following the constants of stress concentration increased. Besides, electric currents were measured through a generator of constant voltage. When connecting constant voltage with corrosion circuit, it was discovered that magnitude of the change come out similarly between displacement on the concrete cover and electric current according to time.

• Structural Engineering and Mechanics
• /
• 제13권2호
• /
• pp.171-186
• /
• 2002

Static and dynamic penetration tests of reinforced concrete (RC) slab specimens are described and discussed. The experimental study was aimed at a better understanding of mechanisms that are involved in dynamic penetration, through their identification in static tests, and by establishing their relative influence in similar dynamic cases. The RC specimens were $80{\times}80-cm$ square plates, and they were made of 30 MPa concrete. The non-deforming steel penetrator was a 50-mm diameter steel rod with a conical nose of 1.5 aspect ratio. Impact penetration tests were carried out with an air gun, which launched the projectiles at velocities of up to 300 m/sec. The static tests were conducted using a closed loop displacement control actuator, where the penetrator was pushed at a constant rate of displacement into the specimen. The static tests reveal important mechanisms that govern the penetration process and therefore contribute to a better understanding of RC barriers resistance to non-deforming projectiles impact.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1373-1383
• /
• 2018

Experimental study was conducted to investigate the seismic behavior of roof joint. Eight full-scale specimens were tested considering the effects of axial force, joint height, hole shape of base plate and edge distance of concrete on the failure mode and resistance capacity of roof joint. With the increase of axial force, the hysteretic curves were fuller. The mechanical model of roof joint change from bending to shear. With the increase of joint height, the ultimate strength of roof joint decreased. If the hole shape of base plate changed from circle to loose, the slip behavior of roof joint appeared and the ultimate strength of roof joint decreased. The damage of edge concrete may occur if the edge distance of concrete was not big enough.

• 대한기계학회논문집A
• /
• 제40권3호
• /
• pp.297-304
• /
• 2016

세라믹(AD-90 alumina, $B_4C$) 타일이 삽입된 금속 블록(4340-steel)에 텅스텐 합금(tungsten alloy)의 긴 운동에너지탄을 수직 고속 충돌시키는 수치해석을 수행하였다. 본 연구를 수행하기에 앞서 두 가지의 반무한판 충돌 모델의 침투 깊이에 대해서 검증을 하였다. 세라믹 재료는 JH-2 (Johnson-Holmquist) 모델을 적용하였고 계산된 침투 깊이를 실험값과 비교하여 만족할만한 결과를 얻었다. 앞서 언급한 판에 대해서 세라믹 타일의 세 가지 두께별로 금속판에 삽입된 위치를 다르게 하여 충돌 시뮬레이션을 수행하였다. 긴 관통자의 잔류속도, 잔류질량 그리고 잔류운동에너지를 얻어 세라믹 타일의 위치가 구조물의 방호 성능에 어떠한 영향을 미치는지 알아보았다. 그리고 단순 금속 블록 대비 세라믹 타일을 사용하는 경우의 질량 효율이 어떻게 되는지 확인해보았다. 마지막으로 이들을 토대로 질량효율 관점에서 최적 방호구조에 대한 평가를 수행하였다.

• Structural Engineering and Mechanics
• /
• 제87권2호
• /
• pp.137-149
• /
• 2023

In this study, to explore the working performance of the CFST split spherical node wind power tower, two groups of CFST split spherical joint plane towers with different web wall thicknesses and a set of space systems were analyzed. The tower was subjected to a low-cycle repeated load test, and the hysteresis and skeleton curves were analyzed. ABAQUS finite element simulation was used for verification and comparison, and on this basis parameter expansion analysis was carried out. The results show that the failure mode of the wind power tower was divided into weld tear damage between belly bar, high strength bolt thread damage and belly rod flexion damage. In addition, increasing the wall thickness of the web member could render the hysteresis curve fuller. Finally, the bearing capacity of the separated spherical node wind power tower was high, but its plastic deformation ability was poor. The ultimate bearing capacity and ductility coefficient of the simulated specimens are positively correlated with web diameter ratio and web column stiffness ratio. When the diameter ratio of the web member was greater than 0.13, or the stiffness ratio γ of the web member to the column was greater than 0.022, the increase of the ultimate bearing capacity and ductility coefficient decreased significantly. In order to maximize the overall mechanical performance of the tower and improve its economy, it was suggested that the diameter ratio of the ventral rod be 0.11-0.13, while the stiffness ratio γ should be 0.02-0.022.

• 열처리공학회지
• /
• 제8권3호
• /
• pp.213-221
• /
• 1995

Temperature distribution, transformation and residual stresses generated during the quenching process of carbon steel. It follows many difficulties in the analytical considerations on those quenching process because of the coupling effects on temperature and metallic structures. In this paper one of the basic study on the quenching stresses was carried out for the case of the round steel bar specimen(SM45C) with 40mm both in its diameter and length. The temperature distributions considering strain hysteresis were numerically calculated by finite element technique. In calculating the transient temperature field, the heat flux between water and rod surface was determined from the heat transfer coefficient. The gradient of temperature is almost same to geometric of specimen. At early stage of the quenching process, the abrupt temperature gradient has been shown in the surface of the specimen.

• 콘크리트학회논문집
• /
• 제19권5호
• /
• pp.577-584
• /
• 2007

Steel microfiber (SMF)가 알칼리-실리카 반응 (ASR)에 미치는 영향을 두 가지 종류 (부순 오팔과 직경이 일정한 pyrex 막대)의 반응 골재를 사용하여 알아보았다. ASR에 의한 균열은 기준 모르타르에서 쉽게 발견되었으나 SMF 모르타르의 균열은 아주 제한적이었다. SMF의 균열 진전 제어 메커니즘을 통하여 ASR에 의한 모르타르의 강도 저하와 팽창을 효과적으로 막을 수 있었고, ASR 생성물들의 유동성이 저하됨을 알 수 있었다. ASR 생성물의 성분을 microprobe 분석과 ICP 분광계를 이용하여 알아보았다. SMF의 구속 효과는 액체상태인 ASR 생성물의 높은 나트륨이 온과 규소이온의 농도를 초래하였으며, 높은 이온의 농도는 ASR 알칼리-실리카 반응성을 저하하는 원인으로 생각되어 진다.

• Corrosion Science and Technology
• /
• 제16권5호
• /
• pp.235-240
• /
• 2017

Regional cathodic protection has significant impact on pipeline integrity management. After risk analyses of a newly built gas distribution station constructed in an area with large dwelling density, risk score was high because of potential threat caused by galvanic corrosion. Except reinforced steel in concrete, there are four kinds of metal buried under earth: carbon steel, galvanized flat steel, zinc rod and graphite module. To protect buried pipeline from external corrosion, design and construction of regional cathodic protection was proposed. Current density was measured with potential using potential dynamic test and boundary element method (BEM) was used to calculate current requirement and optimize best anode placement during design. From our calculation on the potential, optimized conditions for this area were that an applied current was 3A and anode was placed at 40 meters deep from the soil surface. It results in potential range between $-1.128V_{CSE}$ and $-0.863V_{CSE}$, meeting the $-0.85V_{CSE}$ criterion and the $-1.2V_{CSE}$ criterion that no potential was more negative than $-1.2V_{CSE}$ to cause hydrogen evolution at defects in coating of the pipeline.

• Steel and Composite Structures
• /
• 제33권5호
• /
• pp.755-765
• /
• 2019

This study examined geometric and physical nonlinear analyses of beams and arches specifically from rolled profiles used in mining and underground constructions. These profiles possess the ability to create plastic hinges owing to their robustness. It was assumed that displacements in beams and arches fabricated from these profiles were comparable with the size of the structure. It also considered changes in the shape of a rod cross-section and the nonlinearities of the structure. The analyses were based on virtual unit moments, effective flexural rigidity of used open sections, and a secant method. The use of the approach led to a solution for the "after-critical" condition in which deformation increased with decreases in loads. The solution was derived for static determinate beams and static indeterminate arches. The results were compared with results obtained in other experimental tests and methods.