• Steel and Composite Structures
• /
• 제34권1호
• /
• pp.17-34
• /
• 2020

This paper investigates the flexural behavior of concrete beams reinforced longitudinally with either steel bars, molded glass-fiber reinforced polymer (GFRP) grating mesh or pultruded glass-fiber reinforced polymer (GFRP) grating mesh, under four-point bending. The variables included in this study were the type of concrete (normal weight concrete, perlite concrete and vermiculite concrete), type of the longitudinal reinforcement (steel bars, molded and pultruded GFRP grating mesh) and the longitudinal reinforcement ratio (between 0.007 and 0.035). The influences of these variables on the load-midspan deflection curves, bending stiffness, energy absorption and failure modes were investigated. A total of fifteen beams with a cross-sectional dimension of 160 mm × 210 mm and an overall length of 2400 mm were cast and divided into three groups. The first group was constructed with normal weight concrete and served as a reference concrete. The second and third groups were constructed with perlite concrete and vermiculite concrete, respectively. An innovative type of stirrup was used as shear reinforcement for all beams. The results showed that the ultimate load of the beams reinforced with pultruded GFRP grating mesh ranged between 19% and 38% higher than the ultimate load of the beams reinforced with steel bars. The bending stiffness of all beams was influenced by the longitudinal reinforcement ratio rather than the type of concrete. Failure occurred within the pure bending region which means that the innovative stirrups showed a significant resistance to shear failure. Good agreement between the experimental and the analytical ultimate load was obtained.

• 한국산학기술학회논문지
• /
• 제17권2호
• /
• pp.214-219
• /
• 2016

그레이팅은 건축, 토목에서 배수의 주목적으로 하는 구조물이다. 본 연구 에서는 가로형 그레이팅보다 유속에 대한 저항성을 감소시킨 구조인 세로형 그레이팅의 3가지 모델(35.3형, 40형, 43형)을 시뮬레이션하여, 응력 분포 및 변형에 대해 연구하고 최적의 격자 간격의 그레이팅을 설계함이 목적이다. 세로형과 가로형 그레이팅에 하중에 대한 최대 응력 및 변형을 비교 분석하여 보다 나은 제품을 확인하였다.

• 대한기계학회논문집A
• /
• 제38권8호
• /
• pp.905-910
• /
• 2014

본 논문에서 연구한 스틸그레이팅이란 배수로 덮개로 오수 또는 우수의 경사진 유입로를 형성하여 견고성을 증가시키고, 배수를 원활히 하며, 배수관로 내부의 악취 확산을 방지할 수 있는 배수로 덮개를 말한다. 근래에 생활수준 향상 등으로 인해 도시의 악취 문제가 대두되고 있다. 하지만 기존 제품들은 잦은 고장 등으로 인해 악취 저감 기능을 상실하고 이로 인한 행정력과 예산 낭비를 초래하고 있다. 또한 악취 저감 스틸그레이팅 수요 증가에 따라 예산 절감의 필요성이 대두되고 있다. 따라서 본 연구에서는 다구찌 기법과 솔리드웍스를 이용하여 강성적 측면과 배수 성능적 측면에서 스틸그레이팅의 설계 파라미터를 동시적으로 최적화시키고자 하였다.

• Steel and Composite Structures
• /
• 제9권6호
• /
• pp.569-584
• /
• 2009

Corrosion of steel rebars in bridge decks which are faced to harsh conditions, is a common problem in construction industries due to the porosity of concrete. In this research, the behavior of one-way concrete slabs reinforced with Glass fiber reinforced polymer (GFRP) molded grating is investigated both theoretically and experimentally. In the analytical method, a closed-form solution for load-deflection behavior of a slab under four-point bending condition is developed by considering a concrete slab as an orthotropic plate and defining stiffness coefficients in principal directions. The available formulation for concrete reinforced with steel is expanded for concrete reinforced with GFRP molded grating to predict ultimate failure load. In finite element modeling, an exact nonlinear behavior of concrete along with a 3-D failure criterion for cracking and crushing are considered in order to estimate the ultimate failure load and the initial cracking load. Eight concrete slabs reinforced with steel and GFRP grating in various thicknesses are also tested to verify the results. The obtained results from the models and experiments are relatively satisfactory.

• 한국산업융합학회 논문집
• /
• 제24권4_2호
• /
• pp.501-507
• /
• 2021

In this study, In order to prevent the safety accidents caused by the sliding, to develop the non-slip grating, the stability judgment based on the span length of the grating and the gap of the bearing bar is performed. The structural analysis of Grating was carried out in accordance with the provisions set out in Grating's load-bearing test conditions. As the span length increases, the deflection increases and the stress and span length tend to be proportional to each other. It was shown that the larger the span, the linear increase in stress and exponential increase in deformation of grating. The maximum stress of grating was approximately 58.2 MPa, indicating a very stable safety rate of about 4.3 compared to the yield strength of the grating material. Based on these results, it will be able to be utilized as the basic data for determining the optimal dimensions of non-slip grading by performing optimal designs in the future.

• 국제학술발표논문집
• /
• The 3th International Conference on Construction Engineering and Project Management
• /
• pp.1189-1194
• /
• 2009

A gutter-shaped U grating is a facility that is installed at the sides of a road to provide pedestrians with a rainwater-free road. The previous studies on this facility focused mainly on the progress of the efforts that are being made to improve its performance and interception efficiency so as to prevent damages in regional areas due to the heavy rains caused by climate change. The studies on its maintenance, however, are still inadequate. Therefore, this study was conducted to analyze and compare the life cycle costs and performance evaluations of the steel and magic gratings, which are installed in apartments. The results of the study show that the replacement period and rate of gratings differ depending on where they are installed. The initial capital investment cost of a magic grating installed at a road where many vehicles pass is quite high, but in terms of its maintenance and entire-life-cycle costs, its total expenses are lower than those of a steel grating. The results of this study are expected to serve as preliminary data for the selection of an adequate grating that is suitable for particular places in the design phase of construction projects.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2007년도 정기총회 및 학술발표대회
• /
• pp.454-457
• /
• 2007

이 논문은 도로의 침수를 방지하기위하여 집주정 스틸 그레이팅의 설계 방안을 검토하였다. 현재 사용되고 잇는 스틸 그레이팅은 단지 모양만을 고려하여 사용하고 있으며, 차량 하중 등에 대한 고려를 하지 않고 있다. 따라서, 도로설계시 반드시 하중에 대한 검토와 도로표준시방서 등의 검토해야 한다.

• 한국산업융합학회 논문집
• /
• 제25권3호
• /
• pp.357-363
• /
• 2022

In this study, in order to develop an non-slip metal grating, the stability of the grating according to the span of the grating and the gap and height of the bearing bar was evaluated. The optimal shape design of the grating was performed using the results of determining the stability of the grating. The purpose of this study is to determine the stability according to the spacing and height of the bearing bar by applying the design pressure at the design stage to develop the anti-skid grating, and to design the optimal shape for cost reduction. In the optimal design, the target variable was set as the mass, and the optimal design of the grating was performed based on about 20%. Regardless of the height of the bearing bar of the grating, the stress and deformation of the span and the grating showed a proportional tendency to each other, and it was found that the stress decreased as the height of the bearing bar increased. Based on the structural analysis results, an optimal design was performed using mass as the objective variable, and the existing 2mm thickness was changed to 1.6mm, reducing the mass by about 19%. The stress increased by about 4.4% compared to the maximum stress of the existing grating, but the minimum safety factor was 3.1, indicating that the optimally designed grating was stable.

• 대한기계학회논문집
• /
• 제6권3호
• /
• pp.197-203
• /
• 1982

The fatigue crack propagation behavior or non-heat-treatment and thermally aged type 304 stainless steel was investigated on the basis of linear elastic fracture mechanics. This Study was concentrated on the relations between the crack propagation rate and the stress intensity factor range. The following results are obtained : The precision measurement and observation of fatigue crack propagation behavior is studied with moire grating. The effect of thermally aged type 304 stainless steel is investigated under small load. In the equation da/dN=c(.DELTA. k)/SUP m/, factor m of thermally aged steel is a little higher than non-heat-treatmented steel and its limit is m=1.35-4.2.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.440-447
• /
• 2005

In this study, strain measurement and its applicability to estimated deflection curve using fiber bragg grating sensors was conducted. For this purpose, reinforced concrete beams were made and sensors were attached both on the surface of the beams and inside steel. Two types of sensors were used to detect strain on the beams and steel : fiber bragg grating sensors, electric resistance strain sensors. So fatigue test is done with measuring strain of specimen. In addition, this experiments estimates the optimum deflection curve that converts strain curve data measured by FBG sensors into deflection.