• 한국강구조학회 논문집
• /
• 제12권2호통권45호
• /
• pp.167-175
• /
• 2000

본 논문에서는 내후성강재의 고장력볼트 마찰이음부 미끄럼계수 평가를 위한 실험연구를 수행하였다. 표면 상태는 흑피 부착표면을 수동 및 전동솔질로 청소한 경우, 숏브라스트 표면, 무기징크 하도 및 웨더코트를 적용한 경우들을 고려하였다. 또한, 각 표면 상태에 대하여 500 시간 동안 볼트축력 감소율을 측정하였다. 실험결과로부터 흑피표면을 전동솔질한 경우를 제외하면 미끄럼계수는 모두 0.4보다 컸다. 볼트축력 감소율은 표면상태에 따라 달랐으며 $3{\sim}8%$ 정도로서 10% 이내의 값을 보였다.

• 한국강구조학회 논문집
• /
• 제12권2호통권45호
• /
• pp.177-185
• /
• 2000

본 논문에서는 대기 중에 폭로한 내후성강재의 고장력볼트 마찰이음부 미끄럼계수 평가를 위한 실험연구를 수행하였다. 표면 상태는 흑피 부착된 시험체와 숏브라스트로 흑피를 제거한 시험체를 각각 3개월 및 6개월 폭로한 후 수동솔질, 전동솔질 및 청소하지 않은 표면 등을 고려하였다. 또한, 6개월 폭로 시험편의 각 표면 상태에 대하여 600 시간 동안 볼트축력 감소율을 측정하였다. 실험으로부터 모든 시험체에서 폭로 기간에 따라 미끄럼 계수는 증가하였으며 흑피부착 표면을 전동솔질로 청소한 경우를 제외하곤 모두 0.6 이상의 값을 보였다. 볼트 축력 감소율 역시 초기 비폭로 시험체에 비해 폭로한 시험 체에서 증가하였으며 최대 감소율은 약 10%에 이르렀다.

• 제어로봇시스템학회논문지
• /
• 제21권8호
• /
• pp.713-717
• /
• 2015

In this paper, we propose camber monitoring system which is using on hot rolling process. In roughing mill which is one of the rolling part in hot rolling process, steel plate can be bended in width direction under the imbalance of rolling condition. This bending of steel plate in width direction is called as camber. In order to measure the camber, first, cameras which are installed over transport pathway of steel plate take pictures of whole shape of steel plate. And location value of steel plate edge is extrated from these pictures by edge detection algorithm. But, there are a lot of noises which are generated by such as water sprays, dusts, peripheral equipments in these pictures, and these noises make edge detection difficult. In order to solve this kind of problem, we developed a direction selective edge detection algorithm, and applicated in our camber monitoring system. As a result, we got stable results in spite of process noises.

• 건축사
• /
• 통권531호
• /
• pp.60-67
• /
• 2013

• 경영과학
• /
• 제21권3호
• /
• pp.101-113
• /
• 2004

In the rapidly propagating Internet based electronic transaction environment. the importance of real time order confirmation has been more emphasized, In this paper, using data mining techniques, we develop intelligent operations decision model to allow real time order confirmation at the time the customer places an order with required delivery terms. Among various operation plannings used for order fulfillment. mill routing is the first interface decision point to link the order receiving at the marketing with the production planning for order fulfillment. Though linear programming based mathematical optimization techniques are mostly used for mill routing problems, some early orders should wait until sufficient orders are gathered for optimization. And that could effect longer order fulfillment lead-time, and prevent instant order confirmation of delivery terms. To cope with this problem, we provide the intelligent decision model to allow instant order based mill routing decisions. Data mining techniques of decision trees and neural networks. which are more popular in marketing and financial applications, are used to develop the model. Through diverse computational trials with the industrial data from the steel company. we have reported that the performance of the proposed approach is effective compared to the present heuristic only mill routing results. Various issues of data mining techniques application to the mill routing problems having linear programming characteristics are also discussed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.74-80
• /
• 1999

Work roll wear in the cold rolling of mild steel strip is strongly affected by rolling materials, rolling conditions such as roll arrangement in the cold rolling mill and lubrication. The tests were performed to find the effects of roll arrangement n the cold rolling mill on the work roll wear under the same lubricating conditions. The obtained results are as follows:If the distance of cold rolling is about 60km, the surface roughness of its was reduced by half(Ra 0.49${\mu}{\textrm}{m}$) and Pc(peak count) also was decreased to 60 ea/cm.It is easier for CC(Continuous casting) to make a slip on rolling than IC(Ingot casting). It is due to surface mirror in which first residual product appears and iron powder included Al2O3 is sticked. Because bending degree of 4Hi-rolling mill is higher than 6Hi-rolling mill, the first surface mirror was occurred to its center-point which is loaded strongly. 6Hi-rolling mill shape-controlled by intermediate roll doesn't need the initial crown to work roll. Therefore, fatigue and wear would appear a little bit.

• 소음진동
• /
• 제4권1호
• /
• pp.43-50
• /
• 1994

Chatter vibration of a rolling machine in steel plants has a significant effect on thickness quality of the products. The cause and mechanism of the mill chattering is addressed through measurement of vibration and dynamic torque. An FFT system and an FM telemetry system are employed to collect data at several locations of possible damages. The results reveal the followings as sources of the mill vibration. The first is defects in roller bearings of a work roll chock. The second is instability of an oil film bearing in a backup roll chock, which has been investigated with a theoretical model describing the phenomenon. Dynamic torque is not the direct cause of mill vibration but rather influenced by the vibration. Appropriate treatment methods are suggested to address each of the above sources.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.69-72
• /
• 2002

The geometry parameter of tool such as rake angle and clearance angle is defined clearly to solve the difference in communication between design and measurement stage. Using the developed simulation program, wheel is properly determined and end mill can be manufactured accurately. The performance test with well defined end mill provides sufficient information to decide optimal geometry. For machining hardened steel, end mills are designed and manufactured. Optimal rake angle and clearance angle is obtained from performance test. A specific software for automatic end mill production is developed far simulation and fur generation of NC code as Cad/CAM system.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.488-493
• /
• 2003

This paper presents new skill in tube-mill processing getting the increase in production efficiency and quality in response to the recent request of high grade pipe. In this study, researchers developed the method to improve the precision of pipe and tool life in tube-mill processing. Optimum tool shape is devised by analyzing various simulation and mechanism in cutting process. In order to verify the confidence of the proposed machining technology, it is applied to the real processing machinery in the field.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.132-141
• /
• 1999

No. 1 PL(Pickling Line) and No. 1 TCM(Tandem Cold Rolling Mill) at Pohang works started up in 1977 and have been operating successfully keeping high productivity for productivity thin gauge sheat such as BP, CR and silicon steel. On the other hand, customer's requirements of quality level are rasing higher continuously, so that Pohang works has combined and revamped No. 1 PL and No. 1 TCM in order to improve labor productivity, thickness accuracy and shape control capability, and so on in the period of 1977∼1999. This paper introduce the applied facilities, technologies and recent operations after revamping.