• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.1
• /
• pp.85-90
• /
• 2010

Friction welding is a common practice to join axially symmetrical parts for automobile industry applications. The shaft for automobile reverse idle gear is generally produced by forging steel, SF 45. This method is not so good because of high cost of material and production. In this study, in order to investigate the possibility of application of SM 45C to SF 45 dissimilar friction welding, the dissimilar friction welded joints were performed using 20 mm diameter solid bar in forging steel(SF 45) to carbon steel(SM 45C). The optimal friction welding parameters were selected to ensure reliable quality welds on the basis of visual examination, tensile test, micro-Virkers hardness surveys of the bond of area and optical microstructure investigations for welded joint parts. Finally, post weld heat treatment(PWHT) of the high-frequency induction hardening was performed for the friction welded specimens under the optimal welding conditions. And then, the mechanical properties were compared for as-welded and PWHT in SM 45C to SF 45.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.99-101
• /
• 2008

At 21st century, material development concepts were changed to fulfill the environmental friendly demands. This study is to study the effect of pressurized nitrogen gas and manganese in high nitrogen austenitic stainless steel(HNS) in which N and Mn elements substitute the nickel element. 100kg HNS ingots were made by Pressurized Vacuum Induction Melting(P-VIM) and were forged according to free forging process. As forged HNS were hot and cold rolled by pilot scale rolling machine. Depending on the rolling condition, the mechanical properties of HNS were changed. The roll thrust and sheet folding showed asymmetry condition between work and drive side during cold and hot rolling. The purpose of this study are to improve workability the hot and cold rolling machine and to set the conditions for establishing the rolling process.

• Transactions of Materials Processing
• /
• v.19 no.1
• /
• pp.25-31
• /
• 2010

To achieve desired microstructure and mechanical property of a manufacturing product, heat treatment process is applied as a secondary process after forging. Especially, quenching process is used for improving strength, hardness, and wear resistance since phase transformation occurs owing to rapid heat transfer from the surface of the specimen. In the present paper, a study on surface temperature measurement for water quenching of eutectoid steel was investigated. In order to determine the temperature history in experiments, three different measuring schemes were used by varying installation techniques of K-type thermocouples. Depending on the measured temperature distribution at the surface of the specimen, convective heat transfer coefficients were numerically determined as a function of temperature by the inverse finite element analysis considering the latent heat generation due to phase transformation. Based on the inversely determined convective heat transfer coefficient, temperature, phase, and hardness distributions in the specimen after water quenching were numerically predicted. By comparing the experimental and computational hardness distribution at three different locations in the specimen, the best temperature measuring scheme was determined. This work clearly demonstrates the effect of temperature measurement on the final mechanical property in terms of hardness distribution.

• Journal of the Korean Society of Safety
• /
• v.21 no.4 s.76
• /
• pp.33-41
• /
• 2006

Material degradation should be considered to assess integrity and residual life of high temperature equipments. However, the property data reflecting degradation are not sufficient for practical use. In this study measuring properties for 1Cr-1Mo-0.25V forging steel generally used for turbine rotor was carried out. Degradation was simulated by isothermal ageing. heat treatment and variation of microstructure was observed. Mechanical properties such as tensile strength, impact energy, hardness and fracture toughness were measured. Assuming a semi-elliptical surface crack at the bore hole in a turbine rotor, material risk was estimated by using the aged material property data obtained in this study. Safety margin was decreased and life of the rotor was exhausted. This procedure can be used in assessing the residual life of a turbine rotor due to material degradation.

• Journal of Powder Materials
• /
• v.4 no.4
• /
• pp.243-251
• /
• 1997

Engine valve-shaped TiAl-Mn intermetallics containing 43.5 to 47.5at%Al (Mn/Al=0.036) are successively fabricated by reactive sintering the elemental powder mixtures near-net shaped by extrusion and die forging. A duplex structure consisted of lamellar grains and equiaxed $\gamma$ grains is developed for all compositions, and the areal fraction of the lamellar grains(or equiaxed $\gamma$ grains) decreases (or increases) with increasing Al content. As Al content increased, the elongation increases with accompanying decrease in yield strength and ultimate tensile strength at both room temperature and 80$0^{\circ}C$. This indicates that the suitable composition is Ti-45at%Al-1.6at%Mn in considering the balance of ambient and elevated tensile properties. The reactive-sintered Ti-45Al-1.6Mn alloy shows superior oxidation resistance not only to the plasma arc melted one but also to the heat resistance steel STR35(representative exhaust valve head material for automotive engine). The reactive-sintered Ti-45Al-1.6Mn alloy coated with an oxidizing scale exhibits a better wear resistance than induction hardened martensitic steel STR11(representative exhaust valve tip material for automotive engine).

• Applied Microscopy
• /
• v.7 no.1
• /
• pp.45-49
• /
• 1977

For obtaining high manganese steel plates, the study has been made on the optimum conditions in melting, forging, rolling and water toughning treatment practices. The optimum water toughning temperature and time was found to be $1030^{\circ}C$ and 30 min. respectively for the plates of 1 mm thickness. The argon atmosphere is very effective for the prevention of decarburization which can be easily occured in open air. There is a close relation between the degree of c 이 d working and the hardess. The greater the cold reduction ratio is, the smaller the grain size is and it results in the increase of hardness. The improvement of tensile and bending properties can be made by the addition of small amount of nickel, chromium and vanadium.

• 보존과학연구
• /
• s.13
• /
• pp.37-58
• /
• 1992

Iron artifacts from Busǒ Sansǒng inffered to late Baikjae periodwere studied on the aspects of metallugy. These materials were the largest size ever since excavated. From the analytical results these artifacts were found to be pureiron system without impurities or hypo-eutectoid steel system in below 0.3% in carbon contents. From the content of phosphorus in the range of 0.03∼0.05% as aim purity it was shown that charcoal were used for making these iron artifacts from sponge iron not fusion method. By observing metallugical structure it was found that iron artifacts was manufactured by repetitive folding and hammering forging method and some by heating method for adding carbon with cool water. This method were to improve the quality of the soften steel to harden one. In addition to those above repetitive hammering method eliminated the nonferrous materials such as slag inclusion and remained relatively pure ferrite.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.3
• /
• pp.47-49
• /
• 2008

The brake pipe is important part in automobile. The brake pipe have to prevent crack, fracture and defects for braking in safety. Especially, shape of ends of pipe has influence on ability of brake. Based on the procedure of process design, in this paper, the forming operation is designed by finite element method. Design variable and response value was selected shape of die and damage factor. To improve die that performed FEM and compared results of two types of die.

• Design & Manufacturing
• /
• v.9 no.1
• /
• pp.5-8
• /
• 2015

The company Daewoo Precision Industries imported fine blanking press of 40 tons from Switzerland with fine blanking tool in order to produce the fuse part of bomb in 1978 at first in Korea. About 1985 the first fine blanking tool for producing the door lock parts was manufactured in the company Gold Star (now LG). And then this technology was grown up with the growth of automobile industries in Korea. Now 31 companies are closely related to the fine blanking technology and there are total 146 fine blanking presses in Korea. The developments of fine blanking technology in industries have been oriented to the production of precise fine blanking parts, the reduction of die roll height on fine blanking parts, the production of complex fine blanking parts with progressive fine blanking tool including forming and forging technology, the production of high-strength steel fine blanking parts and so on. Some R&D activities in KITECH were introduced.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.68-71
• /
• 2003

Heat treatment is one of the critical manufacturing processes that determine the quality of a product. This paper presents experimental and analytical results for the quench of a ring gear in stagnant oil. The goal of this study is to develop heat transfer predicting model in an overall analysis of the quenching process. Thermal conductivities which are dependant on temperatures and convection coefficients which are obtained by inverse method are used to develop the accurate heat transfer model. The results of heat transfer model have a good agreement with experimental results.