• 한국구조물진단유지관리공학회 논문집
• /
• 제13권4호통권56호
• /
• pp.116-125
• /
• 2009

최근 건설 기술 발달에 따라 공기 단축을 위하여 세그먼트를 공장 제작하고 현장에서 용접 또는 볼팅 등의 방법으로 접합을 하는 시공이 이루어지고 있으며, 확대되고 있는 추세이다. 이때 강과 콘크리트로 구성된 합성부재의 용접시, 용접열이 약 20,000$^{\circ}C, 용접부 주변 온도가 1,300$^{\circ}C 이상이 될 정도로 높은 온도가 생성 된다. 이때 높은 온도로 인하여 용접부와 맞닿아 있는 콘크리트의 강도 감소가 발생하며, 경우에 따라서 국부적으로 강도감소가 매우 큰 곳도 존재하게 되어 구조물 거동에 영향을 미칠 수 있다. 본 연구에서는 이를 방지하기 위해 강재와 콘크리트 사이에 보강재를 삽입하여 용접열에 의한 콘크리트의 강도 감소를 방지하는 방법을 제시하였다.

• 콘크리트학회논문집
• /
• 제14권5호
• /
• pp.734-741
• /
• 2002

중앙부 철골조와 단부 RC조로 이루어진 혼합구조보인 RS 보와 RC 기둥으로 이루어진 접합부의 비탄성 거동 및 내진성능을 구명하기 위하여 반복가력에 의한 접합부 실험을 진행하였다. 본 연구는 RC-RS 접합부의 모멘트비를 변수로 하여 두 개의 내부접합부와 한 개의 외부접합부 등 총 3개의 시험체를 제작하여 실험을 진행하였다. 실험결과, 강도와 연성능력은 충분히 발휘하였으나, 접합부의 강성은 부족한 결과를 나타내었다. 이는 RS 보를 구성하는 철골보와 RC 보를 연결하는 강재매입구간에서의 철골 보의 미끄러짐에 의한 변위의 증가로 인하여 강성의 저하가 발생한 것으로 판단된다. 또한 Hawkins의 제안안에 의한RC-RS 접합부의 내진성능을 평가해 본 결과, 접합부의 초기강성의 부족으로 부재각 0.5 %에서의 공칭강도의 발현은 만족하지 못하였으나, 그외의 내진성능 평가지표인 강도유지능력, 상대 에너지소산비 및 종국후 초기강성비나 초기강도비 등의 측면에서는 우수한 능력을 발휘하였다. 따라서 구조물에서 RC-RS 접합부를 적용할 경우, RC 코어 월과 같은 초기 횡 강성을 보완할 수 있는 적절한 구조시스템과 병행하여 적용하면 강진지역의 구조물에도 충분히 적용이 가능하다고 판단된다.

• 콘크리트학회논문집
• /
• 제23권6호
• /
• pp.711-722
• /
• 2011

횡보강근이 적게 포함된 보통강도 철근콘크리트 보-기둥 접합부에서 강섬유의 보강효과에 관한 실험적 연구를 진행하였다. 이를 규명하기 위해 총 10개의 접합부 실험체를 제작하였으며, 접합부 횡보강근량과 강섬유 혼입률($V_f$ = 0%, 1%, 1.5%)을 주요변수로 실험하였다. 실험은 총 19싸이클의 반복주기하중의 형태로 가력되었으며 각 싸이클의 반복회수는 2싸이클씩 준정적 지진하중의 형태로 적용되었다. 실험 결과를 통해 보통 강도 철근콘크리트 보-기둥 접합부에 강섬유를 보강함으로써 횡보강근 감소에 따른 피해정도를 어느 정도 줄일 수 있다는 결론을 얻었고, 또한 강섬유 보강으로 접합부 전단강도를 증가시킬 수 있고 동시에 에너지소산능력을 향상시킬 수 있다는 결론을 도출하였다. 보다 정량적인 평가를 위해 이 연구의 시험체들과 기존의 보-기둥 접합부 RC 시험체들에서 측정된 최대 접합부 전단강도값과 ACI 352R-02의 설계기준식, Jiuru et al.의 제안식, 그리고 Kim et al.의 제안식을 비교 분석하였다. 이러한 분석 결과 Jiuru et al.의 전단강도 제안식이 실험 결과를 과대평가하는데 반해 Kim et al.의 전단강도 제안식은 모든 시험체에 대해 안정적인 결과와 적은 오차범위를 나타내었다. 따라서, 이 연구를 바탕으로 해서 적절한 접합부 배근상세와 함께 강섬유 보강 철근콘크리트 보-기둥 접합부에 대한 추가적인 연구가 진행된다면, 횡보강근의 감소를 통한 시공의 어려움 해소 및 내진성능의 향상이 가능할 것으로 판단된다.

• 국제초고층학회논문집
• /
• 제5권1호
• /
• pp.1-12
• /
• 2016

The 1100 foot [335 m] tall Wilshire Grand Center tower under construction in Los Angeles illustrates many key outrigger issues. The tower has a long, narrow floor plan and slender central core. Outrigger braces at three groups of levels in the tower help provide for occupant comfort during windy conditions as well as safety during earthquakes. Because outrigger systems are outside the scope of prescriptive code provisions, Performance Based Design (PBD) using Nonlinear Response History Analysis (NRHA) demonstrated acceptability to the Los Angeles building department and its peer review panel. Buckling Restrained Brace (BRB) diagonals are used at all outrigger levels to provide stable cyclic nonlinear behavior and to limit forces generated at columns, connections and core walls. Each diagonal at the lowest set of outriggers includes four individual BRBs to provide exceptional capacities. The middle outriggers have an unusual 'X-braced Vierendeel' configuration to provide clear hotel corridors. The top outriggers are pre-loaded by jacks to address long-term differential shortening between the concrete core and concrete-filled steel perimeter box columns. The outrigger connection details are complex in order to handle large forces and deformations, but were developed with contractor input to enable practical construction.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.14-17
• /
• 2004

A prefabricated composite hollow slab with perforated I-beams was suggested for the replacement of deteriorated concrete decks or the construction of new composite bridges with long-span slabs. Composite slabs with embedded I-beams have considerably higher stiffness and strength. For the application of prefabricated composite slabs to bridges, joints between slabs should satisfy the requirements of the ultimate limit state and the serviceability limit state. In this paper, three types of the detail for loop joints were selected and their structural performance in terms of strength and crack control was investigated through static tests on continuous composite slabs. A main parameter was the detail of the joint, such as an ordinary loop joint and loop joint with additional reinforcements. Even though there was no connection of the steel beams at the joints, the loop joints showed good performance in ultimate strength. In terms of crack control, the loop joint with additional reinforcements showed better performance. In ultimate limit state, the continuous composite slabs showed good moment redistribution and ductility.

• Transactions on Electrical and Electronic Materials
• /
• 제14권1호
• /
• pp.20-23
• /
• 2013

When applying superconducting wire to power machines, an investigation needs to be carried out on the characteristics of wire phase changes in connection with the insulating layer. This study examined trends in the increase of the wire's resistance and the characteristics of its recovery from quenching by a current-applied cycle at temperatures of 90 K, 180 K, and 250 K. The procedure was conducted based on the thickness and presence (or absence) of the insulating wire layers. To achieve this, YBCO thin-film wires with the same critical temperatures were prepared with copper and stainless steel stabilizing layers. At levels (-one, three, and five-), with superior performance, polyimide pressure-sensitive adhesive tape was attached to the wires at a very low temperature. The eight prepared test samples were wound around the linear frames. The wire's voltage and current created from the phase change characteristics were measured at the wire's prescribed temperature, using the four-point probe method. The wire's resistance and recovery characteristics were examined for each cycle at temperatures of 90 K, 180 K, and 250 K.

• Structural Engineering and Mechanics
• /
• 제26권5호
• /
• pp.569-589
• /
• 2007

This paper presents an analytical model for RC beam-column connections that takes into account bond deterioration between reinforcing steel and concrete. The model is based on the Lumped Damage Mechanics (LDM) theory which allows for the characterization of cracking, degradation and yielding, and is extended in this paper by the inclusion of the slip effect as observed in those connections. Slip is assumed to be lumped at inelastic hinges. Thus, the concept of "slip hinge", based on the Coulomb friction plasticity theory, is formulated. The influence of cracking on the slip behavior is taken into account by using two concepts of LDM: the effective moment on an inelastic hinge and the strain equivalence hypothesis. The model is particularly suitable for wide beam-column connections for which bond deterioration dominates the hysteretic response. The model was evaluated by the numerical simulation of five tests reported in the literature. It is found that the model reproduces closely the observed behavior.

• Steel and Composite Structures
• /
• 제22권2호
• /
• pp.323-352
• /
• 2016

The results of a series of finite element (FE) simulations and experimental studies are used to develop strength and stiffness models that predict the failure capacity and response characteristics of unstiffened extended endplate connections with circular and rectangular bolt configurations associated with deep girders. The proposed stiffness models are composed of multi-linear springs which model the overall extended endplate/column flange system deformation and strength of key-components. Comparison of model predictions with FE and experimental results available in the literature show that the proposed models accurately predict the strength and the response of extended endplate/column system with circular and rectangular bolt configurations. The effect of the bolt configuration (circular and rectangular) on the prying phenomenon encountered in the unstiffened extended endplate/column system was investigated. Based on FE results, extended endplate with circular bolt configuration has a more ductile behavior and exhibits higher total prying forces. The proposed models can be used to design connections that cover all possible failure modes for extended endplate with circular bolt configuration. This study provides guidelines for engineers to account for the additional forces induced in the tension bolts and for the maximum rotational capacity demand in the connection which are required for seismic analysis and design.

• 콘크리트학회논문집
• /
• 제15권4호
• /
• pp.625-633
• /
• 2003

For the construction of open-topped steel box girder bridges, prefabricated concrete slab could offer several advantages over cast-in-situ deck including good quality control, fast construction, and elimination of the formwork for concrete slab casting. However, precast decks without reinforcements at transverse joints between precast slabs should be designed to prevent the initiation of cracking at the joints, because the performance of the joint is especially crucial for the integrity of a structural system. Several prestressing methods are available to introduce proper compression at the joints, such as internal tendons, external tendons and support lowering after shear connection. In this paper, experimental results from a continuous composite bridge model with precast decks are presented. Internal tendons and external tendons were used to prevent cracking at the joints. Judging from the tests, precast decks in negative moment regions have the whole contribution to the flexural stiffness of composite section under service loads if appropriate prestressing is introduced. The validity of the calculation of a cracking load fur serviceability was presented by comparing an observed cracking load and the calculated value. Flexural behavior of the continuous composite beam with external prestressing before and after cracking was discussed by using the deflection and strain data.

• Structural Engineering and Mechanics
• /
• 제17권2호
• /
• pp.187-201
• /
• 2004

A shaking table test on a three-story one-bay steel frame model with metallic yield dampers and their parallel connection with oil dampers is carried out to study the dynamic characteristics and seismic performance of the energy dissipation system. It is found from the test that the combined energy dissipation system has favorable reducing vibration effects on structural displacement, and the structural peak acceleration can not evidently be reduced under small intensity seismic excitations, but in most cases the vibration reduction effect is very good under large intensity seismic excitations. Test results also show that stiffness of the energy dissipation devices should match their damping. Dynamic analysis method and mechanics models of these two dampers are proposed. In the analysis method, the force-displacement relationship of the metallic yield damper is represented by an elastic perfectly plastic model, and the behavior of the oil damper is simulated by a velocity and displacement relative model in which the contributions of the oil damper to the damping force and stiffness of the system are considered. Validity of the analytical model and the method is verified through comparison between the results of the shaking table test and numerical analysis.