• Nuclear Engineering and Technology
• /
• 제52권8호
• /
• pp.1677-1688
• /
• 2020

In the sodium-cooled fast reactor, the steam generator is a heat exchange device between sodium and water, which may cause leakage, resulting in a sodium-water reaction accident, which in turn affects the safe operation of the entire nuclear reactor. To this end, the electromagnetic vortex flowmeter is used to detect leakage of the steam generator and its signal processing method is studied in this paper. The hydraulic experiment was carried out by using water instead of liquid sodium, and the sensor output signal of the electromagnetic vortex flowmeter under different gas injection volumes was collected. The bubble noise signal is reflected by the base line of the sensor output signal. According to the relationship between the proportion of the bubble noise signal in the sensor output signal and the gas injection volume, a signal processing method based on the energy ratio calculation is proposed to detect whether the water contains bubbles. The gas injection experiment of liquid sodium was conducted to verify the effectiveness of the signal processing method in the detection of bubbles in sodium, and the minimum detectable leak rate of water in the steam generator was detected to be 0.2 g/s.

• 대한기계학회논문집A
• /
• 제30권8호
• /
• pp.993-1000
• /
• 2006

Operating experience of steam generators has shown that cracks of various morphology frequently occur in the steam generator tubes. These cracked tubes can stay in service if it is proved that the tubes have sufficient safety margin to preclude the risk of burst and leak. Therefore, integrity assessment using exact limit load solutions is very important for safe operation of the steam generators. This paper provides global and local limit load solutions for surface cracks in the steam generator tubes. Such solutions are developed based on three-dimensional (3-D) finite element analyses assuming elastic-perfectly plastic material behavior. For the crack location, both axial and circumferential surface cracks, and for each case, both external and internal cracks are considered. The resulting global and local limit load solutions are given in polynomial forms, and thus can be simply used in practical integrity assessment of the steam generator tubes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.181-182
• /
• 2014

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.109-110
• /
• 2005

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2880-2886
• /
• 2020

A small leak occurring on the surface of a fuel rod due to damage exposes UO₂ to a steam atmosphere. During this time, fission gas trapped inside the fuel rod leaks out, and the gas leakage can be increased due to UO₂ oxidation. Numerous studies have focused on the steam oxidation and its thermodynamic calculation in UO₂. However, the thermodynamic calculation of the UO₂ oxidation in a pressurized water reactor (PWR) environment has not been studied extensively. Moreover, the kinetics of the oxidation of UO₂ pellet also has not been investigated. Therefore, in this study, the thermodynamics of UO₂ oxidation under steam injection due to a damaged fuel rod in a PWR environment is studied. In addition, the diminishing radius of the UO₂ pellet with time in the PWR environment was calculated through an experiment simulating the initial time of steam injection at the puncture.

• 한국압력기기공학회 논문집
• /
• 제16권1호
• /
• pp.42-48
• /
• 2020

The effect of improving the tensile and J-R fracture toughness properties of SA508 Gr.1a on the LBB margin for the main steam pipe is investigated. The material properties and microstructure images of the existing main steam piping material SA106 Gr.C used in domestic nuclear power plants and the newly selected material SA508 Gr.1a were compared. For each material, LBB margins were calculated and compared through finite element analysis and crack instability evaluation. The LBB margin of the improved SA508 Gr.1a is found to be greatly improved compared to that of the existing SA106 Gr.C and SA508 Gr.1a. This is because of the increased material's strength and J-R fracture toughness compared to the previous materials. In order to analyze the effect of physical property change on the LBB margin, the sensitivity of each LBB margin according to the variation of tensile strength and J-R fracture toughness was analyzed. The effect of the change in tensile strength was found to be greater than that of the change in fracture toughness. Therefore, an increase in strength significantly influenced the improvement of the LBB margin of the improved SA508 Gr.1a.

• 한국분무공학회지
• /
• 제9권4호
• /
• pp.24-30
• /
• 2004

Feedwater flowing tube side of number 5 high pressure feedwatrr heaters was heated by extracting steam from high pressure turbine and draining water from moisture separators and number 6 high pressure feedwater heaters and supplied into steam generators. Because the extracting steam from the high pressure turbine is two phase fluid of high temperature, high pressure, and high speed and flows to inverse direction after impinging to impingement baffle. the shell wall of the number 5 high pressure feedwater heater may be affected by flow accelerated corrosion. On May 14, 1999, Point Beach Nuclear Plant (PBNP) with operating at full power experienced a steam leak from rupture of shell side of number 4B feedwater heater. Also, d domestic nuclear power plant experienced a severe wall thinning of shell side of number 5A and 5B feedwater heaters. This paper describes the fluid mixing analysis study using PHOENICS code in order to get at the root of the shell wall thinning of the feedwater heaters. The sections included in the fluid mixing analysis model are around the number 5h feedwater heater shell including the extracting pipeline. To identify the relation between the local velocities and wall thinning. the local velocities according to the analysis results were compared with the distribution of the shell wall thickness by ultrasonic test.

• 대한기계학회논문집A
• /
• 제34권9호
• /
• pp.1217-1225
• /
• 2010

소듐을 냉각재로 사용하는 고속로의 증기발생기에서는 소듐과 물의 화학적 반응을 최소화하는 것이 중요한 문제이다. 소듐과 물의 반응 가능성을 줄여 증기발생기의 신뢰성을 향상시키기 위한 한가지 방안으로 이중벽관을 전열관으로 사용하는 증기발생기를 개발하고 있다. 이 증기발생기에서 중요한 현안은 이중벽관에서의 열전달 성능을 향상시키는 문제와 원자로 운전 중에 소듐과 물 반응사고가 일어나기 전에 전열관의 파손을 감지하는 기술을 개발하는 것이다. 이 논문에서는 이 현안을 극복할 수 있는 방안을 제시하였고, 이 기술을 활용하여 증기발생기의 개념을 설계하였다. 또한 이 개념에 적용되는 이중벽관을 설계 및 예비 제작하여 기계적 시험을 수행하였다.

• Korean Chemical Engineering Research
• /
• 제57권1호
• /
• pp.28-41
• /
• 2019

본 연구는 소듐냉각고속로 원형로 소듐-물 반응 압력완화계통의 성능 해석을 목적으로 한다. 증기발생기의 전열관 파단에 의한 대규모 물 누출 사고 발생 시, 증기발생기 전열관 내측의 물을 급수덤프탱크로 배출하고 전열관 외측의 소듐 및 반응생성물을 소듐덤프탱크로 배출 할 때 유체의 거동을 해석하여 계통 설계요건의 적절성을 평가하였다. 증기발생기 쉘 측의 액체와 중간열전달계통 내 소듐이 모두 배출되는데 소요되는 시간은 약 50초이고, 증기발생기 전열관 측의 급수가 모두 배출되는데 소요되는 시간은 약 2.5초로 계산되었다. 증기발생기와 중간열전달계통 내 유체가 덤프탱크로 배출되는 동안 전열관 측의 압력은 쉘 측의 압력보다 높게 유지되어 쉘 측의 소듐이 전열관 측으로 역류하는 현상은 없는 것으로 해석되었다. 본 연구의 결과는 SFR 원형로 소듐-물반응압력완화계통의 성능 평가에 대한 기초자료로 활용할 예정이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1992년도 추계학술대회논문집; 반도아카데미, 20 Nov. 1992
• /
• pp.81-86
• /
• 1992

원자력발전소 1차 계통 내의 건전성 감시를 위한 설비로는 음향누설 감시계 통(Acoustic Leak Monitoring System: ALMS), 금속파편 감시계통(Loose Parts Monitoring System: LPMS) 및 원자로내부구조물 진동감시계통 (Internals Vibration Monitoring System: IVMS)등이 있다. 현재, 국내의 여 러 원전에는 이들중 일부 계통들이 선택적으로 설치되어 운전중이며, 영광 3,4호기에서는 국내 최초로 이들 3개의 계통을 종합한 핵증기공급계통 건전 성감시계통(Nuclear Steam Supply System Integrity Monitoring System: NIMS)을 설계하였다. 특히, 영광 3,4호기 NIMS에서는 각 계통에 의해 감지 된 1차 계통 내의 이상상태를 하나의 분석컴퓨터(Analysis Computer)를 사 용하여 해석하는 종합결함 탐지해석 기법을 도입하였다.