• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.9-18
• /
• 2000

Combustion and emission characteristics in a direct injection diesel engine is closely related to the intake port system. It is therefore important to understand the swirl flow characteristics formed by a helical intake port. However there are still many uncertainties. The purpose of this experimental study is to investigate the effects of the valve eccentricity ratio and the inlet flow conditions of a helical intake port on the characteristics of an in-cylinder swirl flow. A steady state flow test rig consisted of ISM(impulse swirl meter), LFM(laminar flow meter) and cylinder head with a helical intake port was used. The swirl ratio(Rs) and mean flow coefficient(Cf(mean)) with inlet flow conditions were measured. The results of these experiment can be summarized as follows. Swirl flow characteristics of a helical intake port are affected by the inlet flow conditions, and especially they are much affected by the length of a manifold runner and the rotational angle of a curved manifold runner.

• 드라이브 ㆍ 컨트롤
• /
• 제15권4호
• /
• pp.39-47
• /
• 2018

Recently, as environmental regulations for earth-moving equipment have been tightening, advanced systems such as electronic control, have been introduced for energy savings. An IMV (Independent Metering Valve) consisting of four 2-way valves, is an electro-hydraulic control systems that provides more flexible controllability, and potential for energy savings in excavators, when compared to the conventional 4-way spool valve system. To fully maximize use of an IMV, the bi-directional flow control valve that can regulate a large amount of flow in both directions, should be adopted. The hydraulic circuit of an IMV applied to an excavator from an overseas construction equipment company, reveals the flow control valve with the compound of proportional solenoid valve for first stage, and 2-way spool valve for the second stage. Moreover, the two spools are interconnected by a feedback spring, presumed to compensate for flow force acting on the second stage spool. This paper addresses the static analysis of flow control valve in an IMV to investigate the improvement of robustness, against flow force by the feedback spring. From the steady-state analysis of flow control valve model, it can be concluded that the feedback spring facilitates maintaining linearity of spool displacement for control input, and relatively constant flow for load disturbance.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권6호
• /
• pp.273-284
• /
• 2002

In this paper, computer simulations of the physical Phenomena occurring in the arc region before and after current zero were carried out to evaluate the dielectric recovery characteristics of two types of double-flow nozzles. A commercial CFD Program "PHOENICS" is used for the simulation and the user-coded subroutines to consider the arcing phenomena were added to this program by the authors. The computed results were verified by the comparison with the test results presented by the research group of BBC. In order to investigate the state of the arc region after current zero, the simulation was carried out with four steps. They are cold gas flow analysis, steady state arc simulation, transient arc simulation before current zero, transient hot gas flow simulation after current zero. The semi-experimental arc radiation model is adapted to consider the radiation energy transport and Prandtl′s mixing length model is employed as the turbulence model. The electric field and the magnetic field were calculated with the same grid structure used for the simulation of the flow field. The streamer criterion was introduced to evaluate the dielectric recovery characteristics after current zero. Compared with the results obtained by assuming the current zero state in the former studies, it has been found that the results obtained by considering the state before current zerowere more accurate.

• 한국유체기계학회 논문집
• /
• 제8권4호
• /
• pp.14-19
• /
• 2005

Average Bi-directional flow tube was suggested to measure single and two phase flow rate. Its working principle is similar with Pilot tube, however, it makes it possible to eliminate the cooling system which is normally needed to prevent from flashing in the pressure impulse line of Pilot tube when it is used in the depressurization condition. 3-dimensional steady state flow analyses using FLUENT 5.4 code were performed to validate the application of the average bi-directional flow tube in case of water and air flow. In this study, sensitivity studies have been performed to optimize the design features of the average bi-directional flow tube which can be applied for the various experimental conditions. For Re numbers above 1000, the k values are nearly constant regardless of the Re numbers and flow types and calculation results and experimental data coincides quite well. The current FLUENT calculation results suggest that linearity of the k values in various design features of the average BDFT is highly promising, which means that it is quite reasonable to select the typical design of the average BDFT for the convenience of the experimental conditions.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.180-186
• /
• 2004

Average Bi-directional flow tube was suggested to measure single and two phase flow rate. Its working principle is similar with Pilot tube, however, it makes it possible to eliminate the cooling system which is normally needed to prevent from flashing in the pressure impulse line of Pilot tube when it is used in the depressurization condition. 3-dimensional steady state flow analyses using FLUENT 5.4 code were performed to validate the application of the averagebi-directional flow tube in case of water and air flow In this study, sensitivity studies have been performed to optimize the design features of the average hi-directional flow tube which can be applied for the various experimental conditions. For Re numbers above 1000, the k values are nearly constant regardless of the Re numbers and flow types and calculation results and experimental data coincides quite well. The current FLUENT calculation results suggest that linearity of the k values in various design features of the average BDFT is highly promising, which means that it is quite reasonable to select the typical design of the average BDFT for the convenience of the experimental conditions.

• 한국진공학회지
• /
• 제19권4호
• /
• pp.243-248
• /
• 2010

진공용 기체 유동측정 표준기로 사용하고자 소닉노즐을 ISO 9300에서 제시한 사양에 맞추어 목직경 0.03 mm와 0.2 mm의 소닉 노즐을 제작하였다. 한국표준과학연구원에서 진공용 유량측정 장치로 개발된 정적형 유량계를 이용하여 제작된 2종의 소닉노즐의 유출계수를 확장불확도 3% 이내로 교정하였다. 교정된 소닉노즐의 유량 측정범위는 약 0.6~1,800 cc/min 범위를 갖는 것으로 나타났으며, 사용유동 조건에 해당되는 레이놀드 수(Reynolds number) 범위는 26~12,100으로 확인되었다. 이러한 결과는 교정된 소닉노즐을 이용하여 진공공정에서 필요한 극 미세 유량의 정밀측정을 가능하게 한 새로운 연구결과로 판단된다. 교정된 소닉노즐을 이용하여 진공펌프의 배기속도 측정결과는 기 구축된 정적법을 이용한 배기속도 측정결과와 1% 이내의 오차범위내로 매우 잘 일치함을 보였다. 교정된 소닉노즐은 향후 반도체 및 디스플레이 공정에 사용되는 다양한 건식 진공펌프들의 배기속도를 현장에서 간단하게 평가할 수 있는 현장 성능평가 장치에 활용할 예정이며, 현재 공정현장에서 배기속도 측정에 널리 사용중인 MFC를 대체할 수 있을 것으로 예상된다.

• 대한수학회지
• /
• 제35권3호
• /
• pp.503-525
• /
• 1998

In the theory of retrial queues it is usually assumed that the flow of primary customers is Poisson. This means that the number of independent sources, or potential customers, is infinite and each of them generates primary arrivals very seldom. We consider now retrial queueing systems with a homogeneous population, that is, we assume that a finite number K of identical sources generates the so called quasi-random input. We present a survey of the main results and mathematical tools for finite source retrial queues, concentrating on M/G/1//K and M/M/c//K systems with repeated attempts.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.50-55
• /
• 2002

The transient numerical analysis was performed for vapor cooled current leads. The present numerical modeling considered that there is temperature difference between the copper lead and the helium vapor flow. This numerical modeling was compensated and validated by the experiment with commercially available 100 A current leads. The numerical modeling in this paper described thermal characteristics of overloaded current leads more accurately than the conventional steady state analysis. Proper design of overloaded current leads was suggested by indicating the appropriate overloading factor in the pulse mode operation.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 The Korea-Japan Joint Symposium
• /
• pp.114-114
• /
• 2003

Fiber bundles output from a draft operation have linear density irregularity. This study is dealing with modeling the dynamics of fiber bundle during roll drafting based on continuity, momentum balance, and a constitutive assumption. The simulation results from this model are compared with experimental results and analyzed by applying the concept of the Describing Function(DF). It can be confirmed that the simulation results agree well with experiments in a steady state, if the model parameters are good adjusted.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2005년도 학술발표회(1)
• /
• pp.191-192
• /
• 2005