• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.1
• /
• pp.81-88
• /
• 2020

Flight data recorder is a equipment that records data required for investigation of aircraft accidents and should be developed in compliance with the ED-112A standard. Unlike general data storage device, flight data recorder must be able to recover data after an aircraft accident, requiring a housing and a memory board to protect data in extreme environments. To attain this performance, we designed a housing that can withstand the test by analyzing the physical environment of the impact, shear/tensile, penetration resistance and static crush test of the crash survival test and minimized the size and weight compared to the existing one in consideration of the installation of the aircraft in this paper. Insulation material and thermal block material were applied to endure high and low temperature fire so that the internal temperature does not rise above 150℃ even in 260℃, 10 hour environment. In addition, the memory board is designed to minimize the size and we devise a hoping programming method to prevent continuous data loss of more than 16 seconds. Through this, Crash protected memory module that satisfies ED-112A was completed.

• Resources Recycling
• /
• v.26 no.1
• /
• pp.69-77
• /
• 2017

Used small household appliances(small e-waste) consists of a variety of complex materials and components. The small e-waste is mainly composed of plastics and an important potential source of waste plastic. The black plastics, particularly are very difficult to separate by resin type and therefore these are mainly recycled in the form of a mixtures. In the present study, the sorting technologies such as gravity and electro static separation, near-infrared ray(NIR) and IR/Raman optical sorting separation on mixture of black plastics were analyzed and their limitations on sorting process were also investigated. The Laser Induced Breakdown Spectroscopy(LIBS) spectrum of each black plastics was used for identification of black plastics by resin type, and after analyzing the normalization operation, Principal Component Analysis(PCA) was carried out. The spectrum data was optimized through PCA process. In order to improve the identification accuracy and sorting efficiency of black plastics, it is necessary to design a classifier with high efficiency and to improve the performance and reliability of the classifier by applying the field of intelligent algorithms.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.3-8
• /
• 2009

The traction system has been mainly used for rehabilitation and correction of patients with spine or gait diseases in orthopedics or at home. Some problems could occur in human body when patients forced their training using the traction system. So it needs to measure a traction force and control the training time. However, most of products on market have no sensor measuring traction force. Thus we designed and made a sensor detecting traction force using strain gauge, amplifier for transition to output signal and experiment devices for performance test. We carried out experiment of a sensor detecting a traction force and measured electric responses of it with respect to traction loads. Maximum error was within about 1% for experiments in static condition and the average error was about 0.7% for experiments in dynamic condition. We concluded that it is possible to use the developed sensor for measurement of traction force since the maximum output variation of a sensor detecting a traction force was about 0.3% in $0^{\circ}C-60^{\circ}C$ temperature condition.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.12
• /
• pp.455-462
• /
• 2016

Wireless sensor networks have been researched to gather data about events on sensor fields from sources at sinks. Multipath routing is one of attractive approaches to reliably send data against the problem of frequent breakages on paths from sources to sinks due to node and link failures. As mobile events such as humans, animals, and vehicles are considered, sources may be continuously generated according to the movement of the mobile event. Thus, mobile events provide new challenging issue in multipath routing. However, the research on multipath routing mainly focus on both efficient multipath construction from sources to static sinks and fast multipath reconstruction against path breakages. Accordingly, the previous multipath routing protocols request each source continuously generated by a mobile event to construct individual multipath from the source to sinks. This induces the increase of multipath construction cost in the previous protocols in proportion to the number of source. Therefore, we propose efficient multipath routing protocol for supporting continuous sources generated by mobile events. In the proposed protocol, new source efficiently reconstructs its multipath by exploiting the existing multipath of previous sources. To do this, the proposed protocol selects one among three reconstruction methods: a local reconstruction, a global partial one, and a global full one. For a selection decision, we provide an analytical energy consumption cost model that calculates the summation of both the multipath reconstruction cost and the data forwarding cost. Simulation results show that the proposed protocol has better performance than the previous protocol to provide multipath routing for mobile events.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.8
• /
• pp.317-326
• /
• 2013

In this paper, we present an effective method for comparing control flow graphs which represent static structures of binary programs. To compare control flow graphs, we measure similarities by comparing instructions and syntactic information contained in basic blocks. In addition, we also consider similarities of edges, which represent control flows between basic blocks, by edge extension. Based on the comparison results of basic blocks and edges, we match most similar basic blocks in two control flow graphs, and then calculate the similarity between control flow graphs. We evaluate the proposed edge extension method in real world Java programs with respect to structural similarities of their control flow graphs. To compare the performance of the proposed method, we also performed experiments with a previous structural comparison for control flow graphs. From the experimental results, the proposed method is evaluated to have enough distinction ability between control flow graphs which have different structural characteristics. Although the method takes more time than previous method, it is evaluated to be more resilient than previous method in comparing control flow graphs which have similar structural characteristics. Control flow graph can be effectively used in program analysis and understanding, and the proposed method is expected to be applied to various areas, such as code optimization, detection of similar code, and detection of code plagiarism.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2402-2408
• /
• 2009

This study conducted a static tensile test in order to prevent the lowering of load carrying capacity caused by critical sections made by over bolt holes in the base plate and the cover plate of steel member joints using high-tension bolts. The change of the load carrying capacity of joints was examined by comparison of the maximum load on joint fracture obtained from the tensile test with critical section rate and design strength. According to the results, the rate of decrease in strength was higher when the critical section rate was high, and in particular, decrease in strength was affected much more by critical sections in the base plate than by those in the cover plate. In high-tension bolt joints using over bolt holes for the base plate and the cover plate, load carrying performance was somewhat lower than that in joints using standard bolt holes, but the maximum tensile strength on facture was over 15% higher than design fracture strength. According to the results of this study, the use of over bolt holes in high-tension bolt joints had an insignificant effect on the lowering of load carrying capacity, so the allowance of over bolt holes in the joints of steel members is expected to enhance to the economy and efficiency of the works.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.8-15
• /
• 2021

This paper describes a design method using an optimization technique to satisfy the longitudinal handling quality of high maneuverable jet aircraft. The dynamic inversion technique was applied to the target aircraft, and the control gain optimization satisfied the longitudinal short-period handling quality, however, the stability margin was not considered. If the stability margin is not satisfied, it is necessary to directly readjust the gains through trial and error methods for improvement. To improve this, an additional compensator and an optimization constraint were added to the control gain optimization procedure. In addition, the degree of handling quality satisfaction with the optimization result was reevaluated, and additional control evaluation criteria for the convergence of the time response and the steady state error that the flight performance requirement set as the optimization constraint cannot be reflected, and the results are described.

• Fire Science and Engineering
• /
• v.33 no.2
• /
• pp.145-154
• /
• 2019

The purpose of this study is to analyze the self-status of fire service personnel to identify their effect on self-efficacy and job satisfaction, and to improve the performance of their tasks in the field and perform their tasks efficiently. A survey of 177 current firefighters in the southern city of Gyeonggi Province conducted a correlation analysis and regression analysis through SPSS 22.0. The first study found that in relation to the self-status factor and the self-efficacy factor of firefighting services, the self-efficacy is rather high and the self-regulating effect is very high. Second, the effects of the self-status factor on the self-efficacy were significant in order of type Adult (A), type Free Child (FC), and type Adapted Child (AC). Third, analysis of correlation between self-status factors and job satisfaction factors showed inadequate correlation in all job satisfaction factors for Critical Parent (CP) types, and static correlation in all job satisfaction for Nurturing Parent (NP) types. Type Adapted Child (AC) was less satisfying to itself, to itself, to pay, to promote, to co-workers. Thus, the current strategic approach based on rationality needs to be strengthened by lowering the authority of the Critical Parent (CP) function in terms of self-status factors and enhancing the Adapted Child (AC) function in the lower satisfaction level of the parent.

• Journal of Navigation and Port Research
• /
• v.43 no.3
• /
• pp.172-178
• /
• 2019

Although the needs for providing resilient PNT information are increasing, threats due to the intentional RFI or space weather change are challenging to resolve. eLoran, which is a terrestrial navigation system that use a high-power signal is considered as a best back-up navigation system. Depending on the user's environment in the eLoran system, the user may use one of E-field or H-field antennas. H-field antenna, which has no restriction on setting stable ground and is relatively resistant to noise of general electronic equipment, is composed of two loops, and shows anisotropic gain pattern due to the different measurement at the two loops. Therefore, the H-field antenna's phase estimation value of signal varies depending on its direction even at the static environment. The error due to the direction of the signal should be eliminated if the user want to estimate the own position more precisely. In this paper, a method to compensate the error according to the geometric distribution between the H-field antenna and the transmitting station is proposed. A model was developed to compensate the directional error of H-field antenna based on the signal generated from the eLoran signal simulator. The model is then used to the survey measurement performed in the land area and verify its performance.

• Journal of Navigation and Port Research
• /
• v.43 no.1
• /
• pp.23-32
• /
• 2019

In this paper, we proposed a multi-chain Time of Arrival (ToA) positioning method to estimate positions using all received Loran-C signals from multiple chains without constraining to a single chain. Conventionally, we have to choose only one chain among several available chains for position estimation using Loran-C. Therefore, the number of signals to be used for positioning is limited to three to five. In general, if more signals are used for positioning estimation, its performance tends to be improved in terms of accuracy and availability. To validate the proposed method for multi-chain Loran-C, we firstly carried out a static positioning test in land. By analyzing the test results, we confirmed that the proposed method works well under a multi-chain Loran-C scenario. Subsequently, another mobile positioning test was conducted on board a vessel under a practical application scenario. From this second test, we successfully demonstrated that the multi-chain ToA positioning method even in situations where the conventional single-chain Loran-C approach fails for positioning.