• Journal of Electrical Engineering and Technology
• /
• 제7권6호
• /
• pp.845-851
• /
• 2012

Power system loads have a significant impact on a system. Although it is difficult to precisely describe loads in a mathematical model, accurately modeling them is important for a system analysis. The traditional load modeling method is based on the load components of a bus. Recently, the load modeling method based on measurements from a system has been introduced and developed by researchers. The two major components of a load modeling problem are determining the mathematical model for the target system and estimating the parameters of the determined model. We use the composite load model, which has both static and dynamic load characteristics. The ZIP model and the induction motor model are used for the static and dynamic load models, respectively. In this work, we propose the measurement-based parameter estimation method for the composite load model. The test system and related measurements are obtained using transient security assessment tool(TSAT) simulation program and PSS/E. The parameter estimation is then verified using these measurements. Cases are tested and verified using the sample system and its related measurements.

• International Journal of Concrete Structures and Materials
• /
• 제1권1호
• /
• pp.45-55
• /
• 2007

Ten beams bonded with glass fiber reinforced polymer (GFRP) laminates were tested under cyclic loading with the load range and the FRP reinforcement ratio as test parameters. The maximum load level during cyclic loading was 55%, 65% and 75% of the static flexural strength while the minimum load level was kept constant at 35%. Deflections of the beams at the end of 525000 cycles were found to increase by 16% and 44% when the maximum load level was increased from 55% to 65% and 75% of the static flexural strength, respectively. Beams with FRP reinforcement ratios of 0.64% and 1.28% were found to exhibit lesser deflections of about 15% and 20%, respectively, compared to a similar beam without FRP reinforcement. An analytical approach based on cycle-dependent effective moduli of elasticity of concrete and FRP reinforcement is presented and found to predict the deflections of the test beams well.

• Wind and Structures
• /
• 제19권5호
• /
• pp.565-583
• /
• 2014

Using synchronous surface pressures from the wind tunnel test, the three dimensional wind load models of high-rise buildings are established. Furthermore, the internal force responses of symmetric high-rise buildings in along-wind, across-wind and torsional directions are evaluated based on mode acceleration method, which expresses the restoring force as the summation of quasi-static force and inertia force components. Accordingly the calculation methods of equivalent static wind loads, in which the contributions of the higher modes can be considered, of symmetric high-rise buildings in along-wind, across-wind and torsional directions are deduced based on internal forces equivalence. Finally the equivalent static wind loads of an actual symmetric high-rise building are obtained by this method, and compared with the along-wind equivalent static wind loads obtained by China National Standard.

• 한국공간정보시스템학회:학술대회논문집
• /
• 한국공간정보시스템학회 2004년도 춘계 학술발표회 논문집 제1권1호(통권1호)
• /
• pp.245-251
• /
• 2004

This paper discuss the conditionally sampled actual wind pressure distributions causing peak quasi-static wind loads in the large span roofs using the wind pressures at many locations on dome models measured simultaneously in a wind tunnel. The actual extreme pressure distributions are compared itk load-response-correlation (LRC) method and the quasi-steady pressure distributions. Based on the results, the reason for the discrepancy in the LRC pressure distribution and the actual extreme pressure distribution are discussed. Futhermore, a brief discussion is made of the equivalent static wind load estimation for the large span roofs.

• 한국지반공학회논문집
• /
• 제23권12호
• /
• pp.5-11
• /
• 2007

국내에서는 조립토를 이용한 연약지반 처리공법 중 모래다짐말뚝공법이 많이 활용되고 있으나, 모래자원의 고갈과 단가상승으로 인해 적용이 제한되고 있어 대체공법이 필요한 실정이다. 본 연구에서는 육상부 현장에 시험시공된 단일쇄석다짐말뚝에 대한 정재하시험을 수행하였다. 시험시 말뚝의 직경을 700mm로 고정하구 재하판의 면적을 변화시켰으며, 치환율 20, 30, 40%에 대하여 정재하시험을 실시하였다. 그 결과를 토대로 하여 단일쇄석다짐말뚝의 지지력 증가효과를 평가하였다. 치환율이 증가할수록 침하량이 작아지는 경향을 보였다. 또한, 치환율이 고려된 단일쇄석다짐말뚝의 항복지지력 공식을 제안하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.324-337
• /
• 2010

For the development of load and resistance factor design, reliability analysis is required to calibrate resistance factors in the framework of reliability theory. The distribution of measured-to-predicted pile resistance ratio was constructed based on only the results of load tests conducted to failure for the assessment of uncertainty regarding pile resistance and used in the conventional reliability analysis. In other words, successful pile load test (piles resisted twice their design loads without failure) results were discarded, and therefore, were not reflected in the reliability analysis. In this paper, a new systematic method based on Bayesian theory is used to update reliability index of driven steel pile piles by adding more pile load test results, even not conducted to failure, into the prior distribution of pile resistance ratio. Fifty seven static pile load tests performed to failure in Korea were compiled for the construction of prior distribution of pile resistance ratio. Reliability analyses were performed using the updated distribution of pile resistance ratio and the total load distribution using First-order Reliability Method (FORM). The challenge of this study is that the distribution updates of pile resistance ratio are possible using the load test results even not conducted to failure, and that Bayesian update are most effective when limited data are available for reliability analysis or resistance factors calibration.

• 한국지반공학회논문집
• /
• 제30권8호
• /
• pp.25-37
• /
• 2014

국내 외 하중저항계수설계법의 저항계수 보정 시 수집된 데이터베이스의 신뢰성을 향상시키기 위하여 저항편향계수 산정 단계에서 저항편향치의 ${\pm}2{\sigma}$ 범위의 데이터만을 선택하거나 가정된 확률분포 검정을 만족하도록 꼬리(tail)부분의 데이터를 제거하는 방법을 적용하고 있다. 그러나 이들 방법에서는 데이터베이스 내에 우연히 포함된 저품질의 데이터를 확인할 수 없는 단점이 발견되었다. 본 연구에서는 정재하시험의 품질, 원지반의 공학적 특성, 쇄석다짐말뚝의 제원 등의 품질기준을 이용하여 데이터베이스 구축 단계에서 수행할 수 있는 품질평가법을 제안하였으며, 국내 외 문헌 및 정재하시험 보고서로부터 65개소의 정재하시험 데이터를 수집하여 데이터베이스의 구축 및 품질평가를 수행하였다. 데이터베이스의 품질 평가 상태에 따른 저항편향계수와 변동계수, 저항계수를 비교한 결과, 기존의 데이터베이스 처리과정과 품질평가법을 병행할 경우에 저항편향계수의 불확실성이 감소되며, 신뢰도 높은 LRFD 저항계수 보정에 효과적인 것으로 판단된다.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.261-272
• /
• 2021

This study investigates the structural characteristics of oil-free, gas beam foil journal bearings (GBFJBs) for use in high speed motors. Mathematical modeling was carried out, and reaction force modeling for static load was performed to predict the structural characteristics of the GBFJB. Mathematical modeling and reaction force modeling for static load are performed to predict the structural characteristics of GBFJBs. The reaction force of the test bearing against static loads was measured during experiments and compared with the predicted results. The measured experimental data reveal the nonlinear stiffness characteristics of the GBFJB against varying displacement and agree well with the predictions. Dynamic load tests using an exciter allow to identify the vibration characteristics of the GBFJB. Test results show that the vibration displacement, dynamic force, and acceleration measured on the test bearing are most dominant at the applied dynamic load (synchronization) frequency. Futhermore, the test results show that the hysteresis area recorded during the dynamic tests increases with the excitation amplitude and frequency, and that the beam stick phenomena occurr at high excitation frequencies. The single degree of freedom (DOF) vibration model aids to identify the stiffness and damping coefficient of the GBFJB, which decrease as the excitation frequency increases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.404-409
• /
• 2005

This paper describes the result of structure analysis and load test for bogie frame. The purpose of the analysis and test is to evaluate an safety which body structure shall be considered fully sufficient rigidity so as to satisfy proper system function under maximum load. Bogie system consists of bogie frame, suspensions, wheel-sets, braking system and transmission system. Among these component, the bogie frame is most significant component subjected to the vehicle and passenger loads. The evaluation method is used the JIS E 4207 specification throughout the FEM analysis and static load test. The analysis and test results have been very safety and stable for design load conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.34-38
• /
• 2005

This paper describes the result of load test of a bogie frame. The purpose of test is to evaluate the safety which bogie frame shall be considered fully sufficient rigidity so as to satisfy proper system function under maximum load. Bogie system consist of the bogie frame, suspensions, wheel-sets, a brake system and a transmission system. Among these component, the bogie frame is most significant component subjected to the vehicle and passenger loads. The evaluation method is used the JIS E 4207 specifications throughout the static load test. The test results have shown the bogie frame to be safe and stable under design load conditions.